AURVTN005 - Remove and replace adhesive attached components on vehicles
Assessor Resource
AURVTN005 Remove and replace adhesive attached components on vehicles
Assessment tool
Version 1.0 Issue Date: May 2024
This unit describes the performance outcomes required to remove and replace adhesive attached components on vehicles. It involves preparing for the task, selecting and using tools and equipment, removing and replacing mouldings, badges, transfers and decals, selecting adhesives according to manufacturer specifications, and completing workplace processes and documentation.
It applies to those working in the automotive body service and repair industry.
No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)
Evidence Required
List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements
Elements describe the essential outcomes.
Performance Criteria
Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.
1. Prepare to remove and replace adhesive attached components on vehicles
1.1 Job requirements are determined from workplace instructions
1.2 Removal and replacement information for adhesive attached components is sourced and interpreted from manufacturer specifications and workplace procedures
1.3 Mouldings and decals are sourced and inspected for quality
1.4 Hazards associated with the work are identified and risks are managed
1.5 Tools and equipment, including personal protective equipment (PPE), are identified and checked for serviceability
1.6 Work is planned and removal and replacement procedures are identified to prevent damage to vehicle
2. Remove adhesive attached components on vehicles
2.1 Removal of adhesive attached components is completed using approved equipment from manufacturer, including hot air guns
2.2 Reusable adhesive attached components are inspected and cleaned in preparation for replacement
2.3 Work is completed according to safety and environmental requirements and without causing damage to system and components, including adhesive attached components
3. Attach adhesive components on vehicles
3.1 Components to be replaced are checked and confirmed to be within manufacturer specifications
3.2 Adhesive is selected and applied according to product specification
3.3 Attached components are checked for fit and alignment, and to ensure that they are free of air bubbles
4. Complete work processes
4.1 Final inspection is made to ensure work meets workplace expectations and vehicle is presented ready for use
4.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
4.3 Tools and equipment are checked, reported if faulty, and stored according to workplace procedures
4.4 Workplace documentation is processed according to workplace procedures
Before competency can be determined, individuals must demonstrate they can perform the following according to the standard defined in this unit’s elements, performance criteria, range of conditions and foundation skills:
remove and replace three of the following adhesive attached components on vehicles:
protector mouldings
badges
transfers
decals.
Individuals must be able to demonstrate knowledge of:
work health and safety (WHS) and occupational health and safety (OHS) requirements relating to removing and replacing adhesive attached components on vehicles, including procedures for:
selecting and using personal protective equipment (PPE)
using manual handling and storage techniques
using tools and equipment
handling and storing adhesives
environmental requirements, including procedures for trapping, storing and disposing of waste materials
methods and techniques for removing different types of adhesive attached components, including suitable removal methods and tools
methods and techniques for replacing different types of adhesive attached components, including:
fastening methods: adhesive and mechanical methods
types and application of adhesives
procedures for final inspection of replaced adhesive attached components.
Assessors must satisfy NVR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.
Assessment must include direct observation of tasks.
Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the adhesive attached components they have removed and replaced on vehicles, e.g. repair orders.
Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.
The following resources must be made available:
automotive repair workplace or simulated workplace
workplace instructions
vehicles requiring removal and replacement of adhesive attached components
protector mouldings, transfers, badges and decals to be removed and replaced
tools, equipment and materials appropriate for removing and replacing adhesive attached components, including:
adhesive tape
required PPE.
Submission Requirements
List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here
Assessment task 1: [title] Due date:
(add new lines for each of the assessment tasks)
Assessment Tasks
Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.
Elements
Elements describe the essential outcomes.
Performance Criteria
Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.
1. Prepare to remove and replace adhesive attached components on vehicles
1.1 Job requirements are determined from workplace instructions
1.2 Removal and replacement information for adhesive attached components is sourced and interpreted from manufacturer specifications and workplace procedures
1.3 Mouldings and decals are sourced and inspected for quality
1.4 Hazards associated with the work are identified and risks are managed
1.5 Tools and equipment, including personal protective equipment (PPE), are identified and checked for serviceability
1.6 Work is planned and removal and replacement procedures are identified to prevent damage to vehicle
2. Remove adhesive attached components on vehicles
2.1 Removal of adhesive attached components is completed using approved equipment from manufacturer, including hot air guns
2.2 Reusable adhesive attached components are inspected and cleaned in preparation for replacement
2.3 Work is completed according to safety and environmental requirements and without causing damage to system and components, including adhesive attached components
3. Attach adhesive components on vehicles
3.1 Components to be replaced are checked and confirmed to be within manufacturer specifications
3.2 Adhesive is selected and applied according to product specification
3.3 Attached components are checked for fit and alignment, and to ensure that they are free of air bubbles
4. Complete work processes
4.1 Final inspection is made to ensure work meets workplace expectations and vehicle is presented ready for use
4.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
4.3 Tools and equipment are checked, reported if faulty, and stored according to workplace procedures
4.4 Workplace documentation is processed according to workplace procedures
This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Bold italicised wording, if used in the performance criteria, is detailed below.
Adhesive attached components must include:
protector mouldings
badges
transfers
decals
attachment clips.
Safety and environmental requirements must include:
work health and safety (WHS) and occupational health and safety (OHS) requirements, including procedures for:
selecting and using PPE
using manual handling and storage techniques
using tools and equipment
handling and storing adhesives
environmental requirements, including procedures for trapping, storing and disposing of waste materials.
must include:
attaching mouldings using two-way adhesive tape
attaching transfers and decals following product replacement instructions.
Product specification must include:
type
method
thickness.
Before competency can be determined, individuals must demonstrate they can perform the following according to the standard defined in this unit’s elements, performance criteria, range of conditions and foundation skills:
remove and replace three of the following adhesive attached components on vehicles:
protector mouldings
badges
transfers
decals.
Individuals must be able to demonstrate knowledge of:
work health and safety (WHS) and occupational health and safety (OHS) requirements relating to removing and replacing adhesive attached components on vehicles, including procedures for:
selecting and using personal protective equipment (PPE)
using manual handling and storage techniques
using tools and equipment
handling and storing adhesives
environmental requirements, including procedures for trapping, storing and disposing of waste materials
methods and techniques for removing different types of adhesive attached components, including suitable removal methods and tools
methods and techniques for replacing different types of adhesive attached components, including:
fastening methods: adhesive and mechanical methods
types and application of adhesives
procedures for final inspection of replaced adhesive attached components.
Assessors must satisfy NVR/AQTF assessor requirements.
Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.
Assessment must include direct observation of tasks.
Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the adhesive attached components they have removed and replaced on vehicles, e.g. repair orders.
Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.
The following resources must be made available:
automotive repair workplace or simulated workplace
workplace instructions
vehicles requiring removal and replacement of adhesive attached components
protector mouldings, transfers, badges and decals to be removed and replaced
tools, equipment and materials appropriate for removing and replacing adhesive attached components, including:
adhesive tape
required PPE.
Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.
Observation Checklist
Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice
Yes
No
Comments/feedback
Job requirements are determined from workplace instructions
Removal and replacement information for adhesive attached components is sourced and interpreted from manufacturer specifications and workplace procedures
Mouldings and decals are sourced and inspected for quality
Hazards associated with the work are identified and risks are managed
Tools and equipment, including personal protective equipment (PPE), are identified and checked for serviceability
Work is planned and removal and replacement procedures are identified to prevent damage to vehicle
Removal of adhesive attached components is completed using approved equipment from manufacturer, including hot air guns
Reusable adhesive attached components are inspected and cleaned in preparation for replacement
Work is completed according to safety and environmental requirements and without causing damage to system and components, including adhesive attached components
Components to be replaced are checked and confirmed to be within manufacturer specifications
Adhesive is selected and applied according to product specification
Attached components are checked for fit and alignment, and to ensure that they are free of air bubbles
Final inspection is made to ensure work meets workplace expectations and vehicle is presented ready for use
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
Tools and equipment are checked, reported if faulty, and stored according to workplace procedures
Workplace documentation is processed according to workplace procedures
Job requirements are determined from workplace instructions
Removal and replacement information for adhesive attached components is sourced and interpreted from manufacturer specifications and workplace procedures
Mouldings and decals are sourced and inspected for quality
Hazards associated with the work are identified and risks are managed
Tools and equipment, including personal protective equipment (PPE), are identified and checked for serviceability
Work is planned and removal and replacement procedures are identified to prevent damage to vehicle
Removal of adhesive attached components is completed using approved equipment from manufacturer, including hot air guns
Reusable adhesive attached components are inspected and cleaned in preparation for replacement
Work is completed according to safety and environmental requirements and without causing damage to system and components, including adhesive attached components
Components to be replaced are checked and confirmed to be within manufacturer specifications
Adhesive is selected and applied according to product specification
Attached components are checked for fit and alignment, and to ensure that they are free of air bubbles
Final inspection is made to ensure work meets workplace expectations and vehicle is presented ready for use
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected and stored
Tools and equipment are checked, reported if faulty, and stored according to workplace procedures
Workplace documentation is processed according to workplace procedures
Forms
Assessment Cover Sheet
AURVTN005 - Remove and replace adhesive attached components on vehicles
Assessment task 1: [title]
Student name:
Student ID:
I declare that the assessment tasks submitted for this unit are my own work.
Student signature:
Result: Competent Not yet competent
Feedback to student
Assessor name:
Signature:
Date:
Assessment Record Sheet
AURVTN005 - Remove and replace adhesive attached components on vehicles
Student name:
Student ID:
Assessment task 1: [title] Result: Competent Not yet competent
(add lines for each task)
Feedback to student:
Overall assessment result: Competent Not yet competent