List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
ELEMENT | PERFORMANCE CRITERIA |
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1. Prepare for installation of ribbon fibre | 1.1 Select safety equipment to protect self, co-workers and public in line with WHS and environmental requirements 1.2 Identify and obtain tools and appropriate equipment required for installation 1.3 Check physical conditions relevant to installation and confirm layout of equipment to be installed 1.4 Inform appropriate personnel of identified hazards on worksite 1.5 Locate other services from relevant authorities 1.6 Secure worksite with tests for dangerous gases and guards around open manholes 1.7 Obtain approval for alterations to design within organisational guidelines |
2. Check and secure existing optical fibre cable | 2.1 Following WHS practices, verify that cable was installed according to installation plan and inspect cable for signs of sheath damage 2.2 Maintain minimum bend ratios of cable according to manufacturer specifications while manoeuvring into position 2.3 Secure cable according to safe industry practice, avoiding damage to cable and sheath |
3. Install ribbon fibres into high density drawers and/or pivot sub-racks in internal cabinets | 3.1 Introduce cable into cabinet rack through appropriate route 3.2 Remove cable sheath and lay up ribbon loose tubes into sub-racks without damage to fibre 3.3 Remove loose tubes, clean ribbon fibres and prepare for splicing using organisational techniques 3.4 Splice ribbon fibres and secure into splice holders 3.5 Confirm that fibres are accurately spliced according to organisational specifications |
4. Install and splice ribbon cable in underground enclosures | 4.1 Select appropriate enclosure for function and cable type 4.2 Prepare cables for mid-span and butt splicing following vendor guidelines 4.3 Feed cable accurately into enclosure according to network owner guidelines 4.4 Lay up ribbon fibre in enclosure splice tray to allow accurate and efficient splicing 4.5 Cross-reference fibre numbering to match fibres accurately 4.6 Strip ribbon fibres to specifications 4.7 Splice ribbon fibres accurately 4.8 Apply heat-shrink sleeves to ensure protection of spliced ribbon fibres 4.9 Secure spliced ribbon fibres in splice holders |
5. Close and seal enclosure | 5.1 Check cable and ribbon fibre placement in splice trays conform to vendor and network owner specifications and adjust if necessary 5.2 Close and secure splice trays and fit enclosure cap 5.3 Heat shrink seals around cable entry ports when using heat shrinking techniques, according to vendor and network owner guidelines 5.4 Close and tighten seals around ribbon fibre cables when using mechanical sealing techniques, according to vendor and network owner guidelines 5.5 Check for signs of effective seal and re-seal if necessary |
6. Complete site reinstatement, reporting and sign off requirements | 6.1 Place sealed enclosure in pit and secure to vendor and network owner specifications 6.2 Identify signs of damage or potential damage to pit and cable and take steps to mitigate 6.3 Reinstate site to network owner specifications 6.4 Prepare and finalise reports, including test results and alterations to plans, according to network owner requirements 6.5 Advise client of work completion and obtain sign off |
Evidence of the ability to:
prepare cable for mid-span splicing – strip and coil
prepare cable for butt end splicing – strip and coil
install ribbon fibre cable into:
one heat shrink seal enclosure
one mechanical seal enclosure
one high density ribbon fibre termination drawer
splice ribbon fibre according to specifications
observe all network owner requirements and product practices to ensure optimal performance of cable systems
adapt techniques to a range of technical and environmental conditions.
Note: If a specific volume or frequency is not stated, then evidence must be provided at least once.
To complete the unit requirements safely and effectively, the individual must:
determine the applicable network owner standards, specifications and procedures for cable installation
determine the cable installation requirements, including:
causes of signal strength loss in optical fibre
colour coding and numerical coding of fibres
application of relevant safe operation of laser instruments
installation equipment
specify the industry and organisational policies and procedures when splicing optical fibre cable
identify manufacturer requirements for safe operation of optical fibre equipment
identify common hazards associated with the construction site
describe work health and safety (WHS) and environmental control processes and responsibilities on worksites
describe the safe handling of optical fibres and related equipment including:
hazards relating to handling of optical fibre and laser light source in the workplace
injuries:
damage to retina from lasers
damage to lungs from inhalation of fibre offcuts and particles
needle stick injury from fibres and offcuts
laser warning signs and labels relating to optical fibre components and equipment
safety requirements when handling and working with:
active equipment
laser light sources
optical fibre connectors
optical fibres
patch cords
describe the major feature and use of ribbon fibre, including:
bend ratios for ribbon fibre
procedures for handling and placing ribbon fibre in enclosures
procedures for physical handling of ribbon fibre cables
structure of ribbon fibre cables
splicing techniques for ribbon fibre
types and functions of ribbon fibre enclosures
describe the risks associated with confined spaces and determine the appropriate responses.
Gather evidence to demonstrate consistent performance in conditions that are safe and replicate the workplace. Noise levels, production flow, interruptions and time variances should be typical of those experienced in the telecommunications – cabling field of work and include access to special purpose tools, equipment and materials. These include:
optic fibre cabling and equipment
a range of cabinet types and other housings requiring cable-handling techniques
personal protective equipment
first aid and fire safety equipment
ribbon fibre cleaners, stripper and splicer
joint pressure testing equipment.
Assessors of this unit must satisfy the requirements for assessors in applicable vocational education and training legislation, frameworks and/or standards.