Assessor Resource

LMFFF3005B
Enhance finishes

Assessment tool

Version 1.0
Issue Date: March 2024


This unit covers the competency to cut and buff and to apply materials to a coated surface by hand to enhance the finish.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

Prerequisites

Nil


Employability Skills

This unit contains employability skills.




Evidence Required

List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.

The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Critical Aspects of Evidence

Interpret work order and locate and apply relevant information

Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment

Follow work instructions, operating procedures and inspection practices to:

minimise the risk of injury to self and others

prevent damage to goods, equipment and products

maintain required production output and product quality

On two occasions, one including a curved surface, enhance existing finishes by:

cutting down

pulling in

compounding and buffing

On two occasions wax and oil to achieve a satin finish

Maintain application equipment

Work effectively with others

Modify activities to cater for variations in workplace contexts and environment

Resource Implications

Hand finishing application equipment, compounds, waxes and oils and finishes requiring enhancement.

Method of Assessment

Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.

Assessment should be by direct observation of tasks and questioning on underpinning knowledge.

Assessment should be conducted over time may be in conjunction with assessment of other relevant units of competency.

Context of Assessment

Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.


Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)


Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Required skills

collect, organise and understand information related to coating materials, cleaning materials, work orders and safety procedures

communicate ideas and information to enable confirmation of work requirements and specifications, coordination of work with site supervisor, other workers and customers, and the reporting of work outcomes and problems

plan and organise activities, including the preparation and layout of the worksite and the obtaining of coating equipment and materials to avoid any back tracking, workflow interruptions or wastage

work with others and in a team by recognising dependencies and using cooperative approaches to optimise workflow and productivity

use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate paint and other material requirements

use pre-checking and inspection techniques to anticipate coating problems, avoid re-working and wastage

use the limited workplace technology related to coating, including tools, equipment and measuring devices

Required knowledge

identification of hand application techniques

the functions and safety requirements of hand and power tools, particularly in wet working environments

characteristics of compounds, waxes and oils in terms of toxicity, reactivity, flammability, required viscosity

the methods to prevent contamination of surfaces during and after finishing

workflow in relation to the application of finishing material

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Unit context

OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures

Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements

Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the enhancement of finishes

Surfaces may include but are not limited to:

solid timber

manufactured board

metal

Tools and equipment may include, but are not limited to:

abrasive papers

pulling/pullover rubber

cotton rags

steel wool

orbital sander pneumatic or low voltage

electric or pneumatic buff

rubber sanding block

Materials may include but are not limited to:

water

detergent

cutting compound

wax

oil

buffing creams

Personal protective equipment

Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices

Information and procedures

Workplace procedures relating to the use and operation of tools and equipment

Work instructions, including job sheets, plans, drawing and designs

Workplace procedures relating to reporting and communication

Manufacturers' specifications and operational procedures

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
Workplace information, including materials application, safety information and material safety data sheets, is used to inform work practices 
Characteristics of the surface and the required surface finish are identified from work orders or instructions 
Processing and application techniques, time and safety requirements are identified and used for work planning 
OHS requirements, including ventilation requirements and personal protection needs, are observed throughout the work 
Tools, equipment and accessories are identified and checked for safe and effective operation for the surface finishing task 
Surfaces are checked for contamination and correct preparation according to workplace procedures and standards 
Products with surface or other faults are identified and faults repaired as appropriate 
Finishing materials required are identified and prepared for the task 
Trial applications of surface materials are made to check equipment operation, materials consistency and specified surface finish 
Faults are identified and workplace procedures for rectification are followed 
Techniques for hand application of materials are identified 
Finishing materials are applied according to job instructions, material manufacturers' specifications and workplace procedures 
Finished products are inspected and approved for suitability for further processing 
Products which do not meet quality specifications are refinished or tagged for further investigation 
Equipment used is cleaned and inspected for serviceable condition and stored appropriately 
Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed 
Work area is cleaned and returned to approved condition 
Workplace records are completed 

Forms

Assessment Cover Sheet

LMFFF3005B - Enhance finishes
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:


Assessment Record Sheet

LMFFF3005B - Enhance finishes

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: