Work is generally undertaken in a team environment, but not exclusively.

Control systems can mean closed or open loop on continuous or step process control systems. All specifications are supplied via engineering/circuit drawings, data sheets, written or verbal instructions.

Band: B

Unit Weight: 6

This unit covers planning the commissioning procedure, assessing the control system performance, adjusting the control system, and undertaking commissioning modifications.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

Path 1

MEM09002B

Interpret technical drawing

MEM10002B

Terminate and connect electrical wiring

MEM10003B

Install and test electrical wiring and circuits up to 1000 volts a.c./1500 volts d.c.

MEM12002B

Perform electrical/electronic measurement

MEM12004B

Perform precision electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18048B

Fault find and repair/rectify basic electrical circuits

MEM18049C

Disconnect/reconnect fixed wired equipment up to 1000 volts a.c./1500 volts d.c.

MEM18051B

Fault find repair/rectify complex electrical circuits

Path 2

MEM09002B

Interpret technical drawing

MEM14005A

Plan a complete activity

MEM12002B

Perform electrical/electronic measurement

MEM12003B

Perform precision mechanical measurement

MEM12023A

Perform engineering measurements

MEM12024A

Perform computations

MEM12025A

Use graphical techniques and perform simple statistical computations

MEM16006A

Organise and communicate information

MEM16010B

Write reports

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18003C

Use tools for precision work

MEM18006C

Repair and fit engineering components

MEM18010C

Perform equipment condition monitoring and recording

MEM18016B

Analyse plant and equipment condition monitoring results

MEM18018B

Maintain pneumatic system components

MEM18019B

Maintain pneumatic systems

MEM18020B

Maintain hydraulic system components

MEM18021B

Maintain hydraulic systems

MEM18022B

Maintain fluid power controls

MEM18023B

Modify fluid power system operation

MEM18053B

Modify fluid power control systems

MEM18055B

Dismantle, replace and assemble engineering components

Path 3

MEM05001B

Perform manual soldering/desoldering - electrical/electronic components

MEM09002B

Interpret technical drawing

MEM12004B

Perform precision electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18054B

Fault find, test, calibrate instrumentation systems, equipment

MEM18055B

Dismantle, replace and assemble engineering components

MEM18057B

Maintain/service analog/digital electronic equipment

MEM18060B

Maintain, repair control instrumentation - single and multiple loop control systems

MEM18062B

Install, maintain and calibrate instrumentation sensors, transmitters and final control elements

MEM18067B

Tune control loops - multi controller or multi element systems

Path 4

MEM05001B

Manual soldering/desoldering - electrical/electronic components

MEM05002B

Perform high reliability soldering and desoldering

MEM09002B

Interpret technical drawing

MEM12004B

Perform precision electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18056B

Diagnose and repair analog equipment and components

MEM18057B

Maintain/service analog/digital electronic equipment

MEM18058C

Modify electronic equipment

MEM18059B

Modify electronic systems

MEM18065B

Diagnose and repair digital equipment and components

Path 5

MEM09002B

Interpret technical drawing

MEM12002B

Perform electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18055B

Dismantle, replace and assemble engineering components

MEM18086B

Test, recover, evacuate and charge refrigeration systems

MEM18088B

Maintain and repair commercial air conditioning systems and components

MEM18092B

Maintain and repair commercial and/or industrial refrigeration and/or air conditioning controls

Path 6

MEM09002B

Interpret technical drawing

MEM12002B

Perform electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18055B

Dismantle, replace and assemble engineering components

MEM18086B

Test, recover, evacuate and charge refrigeration systems

MEM18090B

Maintain and repair industrial refrigeration systems and components

MEM18092B

Maintain and repair commercial and/or industrial refrigeration and/or air conditioning controls

Path 7

MEM09002B

Interpret technical drawing

MEM12002B

Perform electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18055B

Dismantle, replace and assemble engineering components

MEM18086B

Test, recover, evacuate and charge refrigeration systems

MEM18089B

Maintain and repair central air handling systems

MEM18090B

Maintain and repair industrial refrigeration systems and components

MEM18093B

Maintain and repair integrated industrial refrigeration and/or large air handling system controls

Path 8

MEM09002B

Interpret technical drawing

MEM12002B

Perform electrical/electronic measurement

MEM12023A

Perform engineering measurements

MEM18001C

Use hand tools

MEM18002B

Use power tools/hand held operations

MEM18054B

Fault find, test, calibrate instrumentation systems, equipment

MEM18055B

Dismantle, replace and assemble engineering components

MEM18060B

Maintain, repair control instrumentation - single and multiple loop control systems

MEM18062B

Install, maintain and calibrate instrumentation sensors, transmitters and final control elements

MEM18064B

Maintain instrumentation system components

MEM18067B

Tune control loops - multi controller or multi element systems

This unit contains employability skills.

List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment	A person who demonstrates competency in this unit must be able to modify control systems. Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit	Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment	This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate. This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with modification of control systems or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment	Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning techniques should not require language, literacy and numeracy skills beyond those required in this unit of competency. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Required skills

Look for evidence that confirms skills in: obtaining, reading, interpreting and following information on written job instructions, specifications, standard operating procedures, charts, lists, drawings and other applicable reference documents obtaining necessary approvals checking system components against specification calibrating and checking test equipment to be used energising and checking the components and/or the control loop/system for correct supply checking and clarifying task-related information adjusting control loop/system components conducting appropriate measurements/tests carrying out authorised modifications to the control system and/or process components checking for conformance to specifications completing reports and documentation on commissioning activity undertaking numerical operations, geometry and calculations/formulae within the scope of this unit

Required knowledge

Look for evidence that confirms knowledge of: work to be undertaken control system format operational intent of the processes being controlled by the control system specifications of the control system and the processes being controlled regulatory and legislative requirements associated with the commissioning procedure procedures for commissioning the control system procedures to ensure that control characteristics, application and process specifications are achieved components of the operational processes installation specifications for each component of the operational processes measuring techniques and equipment appropriate to the measurements to be taken test equipment and techniques appropriate to the commissioning of the control calibration procedures for the selected test equipment procedures for energising components and/or the control loop/system supply requirements of components and the control loop/system recording requirements for readings/measurements taken adjustments that can be made to the control loop/system components effects of adjustments on the control characteristics and operational processes measurements/tests to be undertaken to verify control system and process operation reasons for selecting the chosen measurements/tests procedures to be followed if the operational specifications of the control system and/or process cannot be achieved effect of changes to control system components on system performance appropriate authority to approve any modifications reporting requirements associated with the commissioning of control systems requirements for recording modifications reasons for recording modifications hazard and control measures associated with modifying control systems, including housekeeping safe work practices and procedures

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Commissioning	Commissioning involves the development of a commissioning procedure, testing of operation and adjustment to conform to specification
Control system	Control systems can mean closed or open loop on continuous or step process control systems. Loop/system control can incorporate the use of pneumatics, electrical, electronics, hydraulics or a combination
System components	Control loop/system components incorporate all instruments and devices which make up or control a loop/system, including sensing devices, control devices, actuators and transducers

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Control system format and operational intent is determined and understood.
Commissioning procedures are effectively sequenced to meet requirement of components and control application.
Correct installation of system components is verified against specifications.
Appropriate test equipment is functional and calibrated before use.
Components or control loop/system is powered up and checked for correct supply in accordance with specifications.
All readings/measurements are correctly obtained, interpreted and recorded.
Control loop/system components are adjusted to meet control characteristics, application and process specifications utilising appropriate techniques.
Final verifications including any operational adjustments are made to ensure required performance.
Necessary modifications to change performance in order to meet manufacturers' or operational specifications or safety and legislative requirements are undertaken or actioned.
Reports on system/process characteristics are provided for warranty, handover, legislative, etc. purposes.
All modifications are documented and result is recorded to standard operating procedures.

Assessment Cover Sheet

MEM10007C - Modify control systems

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

MEM10007C - Modify control systems

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: