This unit describes the skills and knowledge required to prepare for work and sand and fill parquetry floors in preparation for applying coating or re-coating to the flooring. It involves operating split drum and/or belt floor sander, rotary or orbital sanding and edge sanding machines.

This unit applies to flooring technicians working in accordance with pre-determined work orders.

Licensing, legislative or certification requirements may apply to this unit and relevant State and local government agencies should be consulted to determine any necessary certification or licensing for undertaking flooring work. Access to construction sites requires certification of general induction training specified by the National Code of Practice for Induction for Construction Work (ASCC 2007).

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
Identify and follow work health and safety, legislative and organisational requirements
Read work documentation and identify job requirements
Identify surface suitability for fine sanding based on contamination and moisture content inspection, and complete pre-sanding requirements
Assess and confirm parquetry flooring condition and the extent of coarse, finish and fine sanding and filling required to meet job specifications
Select and check tools, equipment and materials for suitability, serviceability and safety prior to use
Isolate and/or encapsulate the job site to contain dust fallout from sanding operation
Plan sequence of work to ensure efficiency and quality of application
Set up, check and adjust sanding equipment and safety features in accordance with manufacturer instructions
Select and change equipment to meet requirements of the job
Select, attach and routinely check and change sanding belts or papers to ensure quality finish
Conduct trial runs to check machine operations and quality of finished work
Complete sanding systematically and effectively with the grain, against the grain and across the grain within the minimum required timeframe
Complete required routine lubrication and adjustments to the equipment
Clean and check final finish against quality and job requirements, and rectify deficiencies
Check ventilation before chemical fumes are released, and confirm all WHS and environmental protection requirements are met
Prepare filling material in accordance with manufacturer specifications
Make trial applications of fillers to check equipment operation, materials consistency, viscosity and specified colour
Identify faults and/or inconsistencies in colour and follow workplace procedures for rectification and adjustments
Apply filling material in accordance with manufacturer recommendations and observe drying times between coats
Sand between coats as required in accordance with manufacturer recommendations
Store and recycle unused materials in accordance with workplace procedures
Check, clean and store tools and equipment in accordance with workplace procedures
Clean work area and dispose of rubbish safely
Accurately complete required workplace documentation
Identify and follow work health and safety, legislative and organisational requirements
Read work documentation and identify job requirements
Identify surface suitability for fine sanding based on contamination and moisture content inspection, and complete pre-sanding requirements
Assess and confirm parquetry flooring condition and the extent of coarse, finish and fine sanding and filling required to meet job specifications
Select and check tools, equipment and materials for suitability, serviceability and safety prior to use
Isolate and/or encapsulate the job site to contain dust fallout from sanding operation
Plan sequence of work to ensure efficiency and quality of application
Set up, check and adjust sanding equipment and safety features in accordance with manufacturer instructions
Select and change equipment to meet requirements of the job
Select, attach and routinely check and change sanding belts or papers to ensure quality finish
Conduct trial runs to check machine operations and quality of finished work
Complete sanding systematically and effectively with the grain, against the grain and across the grain within the minimum required timeframe
Complete required routine lubrication and adjustments to the equipment
Clean and check final finish against quality and job requirements, and rectify deficiencies
Check ventilation before chemical fumes are released, and confirm all WHS and environmental protection requirements are met
Prepare filling material in accordance with manufacturer specifications
Make trial applications of fillers to check equipment operation, materials consistency, viscosity and specified colour
Identify faults and/or inconsistencies in colour and follow workplace procedures for rectification and adjustments
Apply filling material in accordance with manufacturer recommendations and observe drying times between coats
Sand between coats as required in accordance with manufacturer recommendations

Assessment Cover Sheet

MSFFL3098 - Sand and fill parquetry flooring

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

MSFFL3098 - Sand and fill parquetry flooring

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: