List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1 | Plan for regulating actions, keys and pedals | 1.1 | Work health and safety (WHS) requirements, legislative requirements and workplace practices relevant to regulating pianos are verified and complied with |
| | 1.2 | Customer requirements are received, analysed and confirmed with appropriate personnel |
| | 1.3 | Communication with others involved with the work is established and maintained to ensure efficient workflow, coordination, personnel cooperation and safety |
| | 1.4 | Written instructions are followed |
2 | Prepare to regulate | 2.1 | Correct posture for regulating is demonstrated which minimises fatigue and promotes muscular control |
| | 2.2 | Tools and equipment are selected consistent with the needs of the job |
| | 2.3 | Selected tools and equipment are checked for service ability and safety, and any faults repaired and reported according to workplace practices |
| | 2.4 | Personal protective equipment is correctly fitted and used |
3 | Align action components | 3.1 | Alignment of action rail is checked and adjusted |
| | 3.2 | Striking distance is adjusted to industry specifications |
| | 3.3 | Hammer running alignment and angling is adjusted |
| | 3.4 | Wippen alignment procedures are performed |
4 | Regulate keyboard | 4.1 | Lost motion is adjusted |
| | 4.2 | Set off is adjusted |
| | 4.3 | Checking distance is adjusted |
| | 4.4 | Dampers are regulated to industry specifications |
| | 4.5 | Damper spoon bending is adjusted to half striking distance |
| | 4.6 | Damper stop rail and jack stop rail are adjusted to industry specifications |
5 | Adjust pedals | 5.1 | Sustain pedal is adjusted to lift when the pedal is one third through its motion |
| | 5.2 | Soft pedal is adjusted to an acceptable lost motion |
| | 5.3 | Mute pedal is adjusted for hammers to clear felt in rest position but strike felt in lockdown position |
| | 5.4 | Sostenuto pedal is adjusted so relevant dampers are locked in position when note is played |
6 | Make final check and inspection | 6.1 | Upright piano is inspected for playability and performance |
| | 6.2 | Adjustments to actions and pedals are made as required |
7 | Clean up work area | 7.1 | All tools, materials and other equipment are checked, cleaned and returned to their appropriate location |
| | 7.2 | Work area is cleared and waste removed |
| | 7.3 | Workplace documentation is completed and filed |
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Regulate a minimum of three (3) actions, keys and pedals in upright pianos
Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements
Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures
Avoid backtracking, work flow interruptions or wastage
Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity
State or territory WHS legislation, regulations, standards and codes of practice relevant to the full range of processes for regulating upright piano actions, keys and pedals
Organisational and site standards, requirements, policies and procedures for regulating upright piano actions, keys and pedals
Reading and interpreting workplace documents, including work orders, work instructions and operator instructions
Environmental protection requirements relating to the disposal of waste material
Established lines of communication and protocols
Types, characteristics, uses, limitations and preparation of materials and equipment used in piano regulating
Types of tools and equipment used to regulate actions, keys and pedals and procedures for their safe use, operation and maintenance
Relevant problem identification and resolution
Set-up and operation of tools and equipment used for regulating actions, keys and pedals
Storage systems and labelling
Procedures for the recording, reporting and maintenance of workplace records and information
Appropriate mathematical procedures for estimation and measurement
Assessors must:
hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors
have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification
be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.
Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.
Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.
Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.
Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.
Access is required to hand and power tools used to regulate actions, keys and pedals of upright pianos, safety and personal protective equipment, holding and supporting equipment, and upright pianos.