List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1 | Set up mould and accessories | 1.1 | Fit reinforcement and fittings according to work instructions |
| 1.2 | Pre-stress reinforcement as required |
| 1.3 | Strap pipes/accessories down as required |
| 1.4 | Inspect mould assembly is to specification |
| 1.5 | Check mould for defects and correct if required |
|
2 | Prepare equipment for the mix | 2.1 | Set up tools required |
| 2.2 | Set up vibrators to standard |
| 2.3 | Ensure concrete dispenser is in action |
| 2.4 | Ensure mix is to standard consistency |
|
3 | Cast concrete into moulds | 3.1 | Check casting schedule, job specification and drawings |
| 3.2 | Clean, seal and oil moulds as required |
| 3.3 | Pour mix into mould at correct speed |
| 3.4 | Vibrate according to standard operating procedures (SOPs) |
| 3.5 | Finish and cover mould as required |
| 3.6 | Clean mould and work site as required by good occupational hygiene practices |
|
4 | Rectify routine problems | 4.1 | Identify the range of faults that can occur during the operation |
| 4.2 | Determine and rectify fault causes in accordance with procedures/work instructions |
| 4.3 | Identify and rectify equipment failure causes in accordance with procedures/work instructions |
| 4.4 | Make sure appropriate records and log books of equipment operations are maintained to meet procedures/work instructions |
| 4.5 | Identify non-routine problems and report to designated person |
|
5 | Control hazards | 5.1 | Identify hazards from the job to be done |
| 5.2 | Identify other hazards in the work area |
| 5.3 | Assess the risks arising from those hazards |
| 5.4 | Implement measures to control those risks in line with procedures |
Evidence required to demonstrate competence in this unit must be relevant to and satisfy the requirements of the elements and performance criteria and demonstrate the ability to:
read and interpret job sheets, procedures, material labels and safety information
select and prepare moulds, accessories, equipment and materials to meet specifications
pre-stress reinforcement
monitor key variables, including:
mould condition
amount and grade of concrete
consistency of mix
placement of reinforcing and accessories
placement and stressing of strands
compaction/vibration
product integrity and conformance to specification
make adjustments to meet product quality and production output specifications
identify hazards and apply relevant hazard controls
apply safety procedures
apply housekeeping procedures
recognise out-of-specification products, process problems and materials faults
recognise routine and non-routine problems
identify when the operator is able to rectify problems, when assistance is required and who is the appropriate source for assistance
take action to resolve problems or report them to appropriate personnel
distinguish between possible causes of routine problems, including:
raw material/mix variations
mould anomalies
casting/operating conditions
process errors
communicate effectively with team/work group and supervisors
complete workplace records
do basic arithmetical manipulations, including additions, subtractions, divisions, fractions and percentages.
Must provide evidence that demonstrates knowledge relevant to their job sufficient to operate under routine only supervision and to solve routine problems, including knowledge of:
common types of moulds and their application
causes and impact of mould wear
problems resulting from mould leakage
importance of vibration on compaction
basic physics and chemistry relevant to the equipment/process/materials
role of reinforcement, types of reinforcement and significance of concrete cover
hazards from pre-stressed reinforcement
the potential effects of variations in raw materials and equipment operation/processes in relation to quality of product
factors which may affect product quality or production output and appropriate remedies
routine problems, their probable causes and relevant corrective actions
organisation procedures relevant to the work environment/job role
hierarchy of control
hazards that may arise in the job/work environment and:
their possible causes
potential consequences
appropriate risk controls.
The unit should be assessed holistically and the judgement of competence shall be based on a holistic assessment of the evidence.
The collection of performance evidence:
should occur over a range of situations which include typical disruptions to normal, smooth operation of an operating plant
will typically include a supervisor/third-party report or other evidence, focusing on consistent performance and problem recognition and solving. A supervisor/third-party report must be prepared by someone who has a direct, relevant, current relationship with the person being assessed and who is in a position to form a judgement on workplace performance relevant to the unit of competency
must include the use of an appropriate industrial item/s of equipment requiring demonstration of operation, start-up and shutdown procedures and responding to problems
may use industry-based simulation for all or part of the unit particularly where safety, lack of opportunity or significant cost is an issue.
Assessment should occur in operational workplace situations. Where this is not possible or where personal safety or environmental damage are limiting factors assessment must occur in a sufficiently rigorous simulated environment that reflects realistic operational workplace conditions. This must cover all aspects of workplace performance, including environment, task skills, task management skills, contingency management skills and job role environment skills.
Assessment in a simulated environment should use evidence collected from demonstration of skills and one or more of:
walk-throughs
pilot plant operation
industry-based case studies/scenarios
‘what ifs’.
Knowledge evidence may be collected concurrently with performance evidence (provided a record is kept) or through an independent process such as workbooks, written assessments or interviews (provided a record is kept).
Assessment processes and techniques must be appropriate to the language, literacy and numeracy requirements of the work being performed and the needs of the candidate.
Conditions for assessment must include access to all tools, equipment, materials and documentation required, including relevant workplace procedures, product and manufacturing specifications associated with this unit.
The regulatory framework will be reflected in workplace policies and procedures and is not required to be independently assessed.
Foundation skills are integral to competent performance of the unit and should not be assessed separately.
Assessors must satisfy the assessor competency requirements that are in place at the time of the assessment as set by the VET regulator.
In addition the assessor or anyone acting in subject matter expert role in assessment shall demonstrate both technical competency and currency. If the assessor cannot demonstrate technical competency and currency they shall assess with a subject matter expert who does meet these requirements.
Technical competence can be demonstrated through one or more of:
relevant VET or other qualification/Statement of Attainment
appropriate workplace experience undertaking the type of work being assessed under routine and non-routine conditions
appropriate workplace experience supervising/evaluating the type of work being assessed under routine and non-routine conditions
Currency can be demonstrated through one or more of:
being currently employed undertaking the type of work being assessed
being employed by the organisation undertaking the type of work being assessed and having maintained currency in accordance with that organisation’s policies and procedures
having consulted/had contact with an organisation undertaking the type of work being assessed within the last twelve months, the consultation/contact being related to assessment
conducting on the job training/assessments of the type of work being assessed
being an active member of a relevant professional body and participating in activities relevant to the assessment of this type of work.