List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1 | Develop mould design | 1.1 | Establish original product concept or design from drawings, originals or consultation with the customer |
| 1.2 | Sketch out product prototype design and establish product sizes making appropriate allowance for material shrinkage |
| 1.3 | Identify areas where undercuts, cutbacks or other special features are required |
| 1.4 | Determine parting line |
| 1.5 | Determine material from which mould is to be made |
|
2 | Select mould material and prepare for mould production | 2.1 | Set up material for mould making, ensuring that the mould can be handled or moved without damage |
| 2.2 | Establish datum point and mark out design dimensions using geometric and lineal calculations |
| 2.3 | Determine correct cavity depths and contours |
| 2.4 | Ensure there is adequate ventilation and light to facilitate an appropriate work environment |
|
3 | Produce working mould | 3.1 | Fit appropriate protective equipment to prevent inhalation or irritation of by-products of the mould making process |
| 3.2 | Use appropriate tools to carve out mould cavity and detail |
| 3.3 | Accurately follow the design detail to produce a mould cavity to specification |
| 3.4 | Avoid undercuts which will prevent removal of the plaster product from the mould |
| 3.5 | Ensure appropriate degrees of taper are provided to facilitate product removal |
| 3.6 | Carve reliefs according to design and remove debris as the work proceeds |
|
4 | Complete mould | 4.1 | Clean down completed mould and clean up work area |
| 4.2 | Inspect mould surface for defects or irregularities |
| 4.3 | Compare design details with mould cavity to confirm accuracy of translation |
| 4.4 | Coat mould surface to preserve finish and allow to dry |
|
5 | Produce product prototype | 5.1 | Apply slipping agent to mould surface |
| 5.2 | Prepare and insert anchors or ties |
| 5.3 | Prepare plaster mixture and appropriate amount of glass fibre |
| 5.4 | Cast plaster mix and fibre into mould cavity, strike off and allow to set |
| 5.5 | Remove prototype from mould or mould from prototype |
| 5.6 | Check prototype for dimensional and detail accuracy |
| 5.7 | Compare prototype and mould to identify any faults or mould inaccuracies |
| 5.8 | Adjust or dress mould to remove imperfections and clean mould surface |
| 5.9 | Cast second prototype and recheck product and mould |
| 5.10 | Clean up mould and mark in accordance with organisation identification practice |
|
6 | Control hazards | 6.1 | Identify hazards in modelling work area |
| 6.2 | Assess the risks arising from those hazards |
| 6.3 | Implement measures to control those risks in line with procedures and duty of care |
|
7 | Respond to problems | 7.1 | Identify possible routine and non-routine problems in the equipment or process |
| 7.2 | Determine problems needing action |
| 7.3 | Determine possible fault causes |
| 7.4 | Rectify problem using appropriate solution within area of responsibility |
| 7.5 | Report problems outside area of responsibility to designated person |
Evidence required to demonstrate competence in this unit must be relevant to and satisfy the requirements of the elements and performance criteria and demonstrate the ability to:
read and interpret product specifications, designs, drawings/plans, material labels and safety data sheets (SDS)
establish product concept and develop mould design to meet specifications
determine datum point and mark out dimensions, contours and cavity depths
carve out mould to meet specifications
prepare mould, produce and demould prototype product
review prototype for conformity to specifications
make adjustments to mould to remedy faults and non-conformity
identify hazards and apply relevant hazard controls
apply safety procedures
apply housekeeping procedures
distinguish between causes of problems, including:
equipment failure/malfunction
wrong readings/measurements
materials faults
dimensional inaccuracies
inappropriate allowance for material shrinkage
damage to components
recognise and prioritise problems requiring action
resolve routine and non-routine problems
communicate effectively with team/work group and supervisors
complete workplace records
perform geometric and lineal calculations.
Must provide evidence that demonstrates knowledge relevant to their job sufficient to operate independently and to solve routine and non-routine problems, including knowledge of:
principles of fibrous plaster product moulding processes
types and application of mould making materials, including:
plaster
timber
rubber
metal
product specifications/materials properties that may affect mould design, materials and construction
quality requirements at each stage of construction
factors which may affect mould quality and appropriate remedies
non-routine problems that may arise, the range of possible causes and appropriate actions
organisation procedures relevant to the work environment/job role
hierarchy of control
hazards that may arise in the job/work environment and:
their possible causes
potential consequences
appropriate risk controls.
The unit should be assessed holistically and the judgement of competence shall be based on a holistic assessment of the evidence.
The collection of performance evidence:
should occur over a range of situations which include typical disruptions to normal, smooth operation of an operating plant
will typically include a supervisor/third-party report or other evidence, focusing on consistent performance and problem recognition and solving. A supervisor/third-party report must be prepared by someone who has a direct, relevant, current relationship with the person being assessed and who is in a position to form a judgement on workplace performance relevant to the unit of competency
must include the use of an appropriate industrial item/s of equipment requiring demonstration of operation, start-up and shutdown procedures and responding to problems
may use industry-based simulation for all or part of the unit particularly where safety, lack of opportunity or significant cost is an issue.
Assessment should occur in operational workplace situations. Where this is not possible or where personal safety or environmental damage are limiting factors assessment must occur in a sufficiently rigorous simulated environment that reflects realistic operational workplace conditions. This must cover all aspects of workplace performance, including environment, task skills, task management skills, contingency management skills and job role environment skills.
Assessment in a simulated environment should use evidence collected from demonstration of skills and one or more of:
walk-throughs
pilot plant operation
industry-based case studies/scenarios
‘what ifs’.
Knowledge evidence may be collected concurrently with performance evidence (provided a record is kept) or through an independent process such as workbooks, written assessments or interviews (provided a record is kept).
Assessment processes and techniques must be appropriate to the language, literacy and numeracy requirements of the work being performed and the needs of the candidate.
Conditions for assessment must include access to all tools, equipment, materials and documentation required, including relevant workplace procedures, product and manufacturing specifications associated with this unit.
The regulatory framework will be reflected in workplace policies and procedures and is not required to be independently assessed.
Foundation skills are integral to competent performance of the unit and should not be assessed separately.
Assessors must satisfy the assessor competency requirements that are in place at the time of the assessment as set by the VET regulator.
In addition the assessor or anyone acting in subject matter expert role in assessment shall demonstrate both technical competency and currency. If the assessor cannot demonstrate technical competency and currency they shall assess with a subject matter expert who does meet these requirements.
Technical competence can be demonstrated through one or more of:
relevant VET or other qualification/Statement of Attainment
appropriate workplace experience undertaking the type of work being assessed under routine and non-routine conditions
appropriate workplace experience supervising/evaluating the type of work being assessed under routine and non-routine conditions
Currency can be demonstrated through one or more of:
being currently employed undertaking the type of work being assessed
being employed by the organisation undertaking the type of work being assessed and having maintained currency in accordance with that organisation’s policies and procedures
having consulted/had contact with an organisation undertaking the type of work being assessed within the last twelve months, the consultation/contact being related to assessment
conducting on the job training/assessments of the type of work being assessed
being an active member of a relevant professional body and participating in activities relevant to the assessment of this type of work.