List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. |
1 | Design and make models | 1.1 | Establish model design from drawings, originals or in consultation with the customer |
| 1.2 | Select and prepare appropriate materials for model construction |
| 1.3 | Make models ensuring the final product is to specification, and shrinkage is allowed for |
|
2 | Set up and produce block moulds | 2.1 | Select appropriate model to meet specification |
| 2.2 | Determine required sections and parting lines |
| 2.3 | Check mould meets work health and safety (WHS) needs |
| 2.4 | Mix materials as required |
| 2.5 | Fill mould with mould material as required |
| 2.6 | Remove mould from model when required strength has been achieved |
| 2.7 | Finish mould to specifications and register correctly |
|
3 | Prepare cases and frames | 3.1 | Consult manufacturing schedule to determine type of mould to be made |
| 3.2 | Select appropriate frame or frames |
| 3.3 | Mix materials as required |
| 3.4 | Fill block mould |
| 3.5 | Remove block mould from the case and frame when required strength has been obtained |
| 3.6 | Register and date cases according to procedures |
| 3.7 | Prepare block mould for use |
|
4 | Prepare and make working moulds | 4.1 | Select the appropriate case/frame |
| 4.2 | Mix and pour mould material as required |
| 4.3 | Remove mould from model when required strength has been obtained |
| 4.4 | Finish and register moulds to procedures |
| 4.5 | Stack and dry moulds to procedures |
| 4.6 | Store moulds to procedures |
|
5 | Prepare dies | 5.1 | Consult manufacturing schedule to determine type of die to be made |
| 5.2 | Select and prepare required master die |
| 5.3 | Mix and pour die material as required |
| 5.4 | Remove die from master die when required strength has been obtained |
| 5.5 | Mark and finish dies to enterprise specifications |
| 5.6 | Cure and store dies to procedures |
|
6 | Respond to problems | 6.1 | Identify possible routine and non-routine problems in the equipment or process |
| 6.2 | Determine problems needing action |
| 6.3 | Determine possible fault causes |
| 6.4 | Rectify problem using appropriate solution within area of responsibility |
| 6.5 | Report problems outside area of responsibility to designated person |
Evidence required to demonstrate competence in this unit must be relevant to and satisfy the requirements of the elements and performance criteria and demonstrate the ability to:
read and interpret drawings, production schedules, job sheets, procedures, material labels and safety information
establish specifications for devices, including:
models
block moulds
working moulds
dies
design and make models to specifications
produce block moulds, working moulds and dies
select and prepare and use materials, fittings, tools and equipment
monitor key variables, including:
raw materials/mix
shape
dimensions
shrinkage
strength
device integrity and conformance to specification of the moulding item
make adjustments/repairs to ensure device and meets quality and production output specifications
identify hazards and apply relevant hazard controls
handle/store devices
apply safety procedures
· apply housekeeping procedures
· recognise out-of-specification products, process problems and materials faults
resolve routine and non-routine problems
identify when the operator is able to rectify problems, when assistance is required and who is the appropriate source for assistance
take action to resolve problems or report them to appropriate personnel
distinguish between possible causes of routine problems, including:
incorrect materials
variations in materials
equipment malfunction
procedure errors
incorrect specifications
communicate effectively with team/work group and supervisors
complete workplace records
do basic arithmetical manipulations, including additions, subtractions, divisions, fractions and percentages.
Must provide evidence that demonstrates knowledge relevant to their job sufficient to fulfil their job role, including knowledge of:
principles of design as applicable to models
functions and limitations of devices, including:
models
block moulds
frames and cases
working moulds
dies and master dies
types of materials relevant to making the devices and their application, including:
plaster
timber
rubber
metal
fibreglass
product specifications/materials properties that may affect device design, materials and construction
quality requirements at each stage of construction
factors which may affect device quality and appropriate remedies
non-routine problems that may arise, the range of possible causes and appropriate actions
organisation procedures relevant to the work environment/job role
hierarchy of control
hazards that may arise in the job/work environment and:
their possible causes
potential consequences
appropriate risk controls.
The unit should be assessed holistically and the judgement of competence shall be based on a holistic assessment of the evidence.
The collection of performance evidence:
should occur over a range of situations which include typical disruptions to normal, smooth operation of an operating plant
will typically include a supervisor/third-party report or other evidence, focusing on consistent performance and problem recognition and solving. A supervisor/third-party report must be prepared by someone who has a direct, relevant, current relationship with the person being assessed and who is in a position to form a judgement on workplace performance relevant to the unit of competency
must include the use of an appropriate industrial item/s of equipment requiring demonstration of operation, start-up and shutdown procedures and responding to problems
may use industry-based simulation for all or part of the unit particularly where safety, lack of opportunity or significant cost is an issue.
Assessment should occur in operational workplace situations. Where this is not possible or where personal safety or environmental damage are limiting factors assessment must occur in a sufficiently rigorous simulated environment that reflects realistic operational workplace conditions. This must cover all aspects of workplace performance, including environment, task skills, task management skills, contingency management skills and job role environment skills.
Assessment in a simulated environment should use evidence collected from demonstration of skills and one or more of:
walk-throughs
pilot plant operation
industry-based case studies/scenarios
‘what ifs’.
Knowledge evidence may be collected concurrently with performance evidence (provided a record is kept) or through an independent process such as workbooks, written assessments or interviews (provided a record is kept).
Assessment processes and techniques must be appropriate to the language, literacy and numeracy requirements of the work being performed and the needs of the candidate.
Conditions for assessment must include access to all tools, equipment, materials and documentation required, including relevant workplace procedures, product and manufacturing specifications associated with this unit.
The regulatory framework will be reflected in workplace policies and procedures and is not required to be independently assessed.
Foundation skills are integral to competent performance of the unit and should not be assessed separately.
Assessors must satisfy the assessor competency requirements that are in place at the time of the assessment as set by the VET regulator.
In addition the assessor or anyone acting in subject matter expert role in assessment shall demonstrate both technical competency and currency. If the assessor cannot demonstrate technical competency and currency they shall assess with a subject matter expert who does meet these requirements.
Technical competence can be demonstrated through one or more of:
relevant VET or other qualification/Statement of Attainment
appropriate workplace experience undertaking the type of work being assessed under routine and non-routine conditions
appropriate workplace experience supervising/evaluating the type of work being assessed under routine and non-routine conditions
Currency can be demonstrated through one or more of:
being currently employed undertaking the type of work being assessed
being employed by the organisation undertaking the type of work being assessed and having maintained currency in accordance with that organisation’s policies and procedures
having consulted/had contact with an organisation undertaking the type of work being assessed within the last twelve months, the consultation/contact being related to assessment
conducting on the job training/assessments of the type of work being assessed
being an active member of a relevant professional body and participating in activities relevant to the assessment of this type of work.