List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
1. Plan and prepare for reagents handling | 1.1. Access, interpret and apply reagents handling documentation and ensure the work activity is compliant 1.2. Obtain, read, interpret, clarify and confirm work instructions 1.3. Select, and check for faults, equipment/tools for work activities 1.4. Select and wear personal protective equipment appropriate for the activity 1.5. Identify and address potential risks, hazards and environmental issues, and implement control measures 1.6. Obtain and interpret emergency procedures, and be prepared for fire/accident/ emergency 1.7. Communicate with other personnel using approved communication methods 1.8. Select appropriate type of auxiliary equipment for work activities 1.9. Perform equipment pre-start checks 1.10. Select appropriate reagents 1.11. Use approved fume suppression and extraction methods |
2. Start-up equipment in sequence | 2.1. Carry out start-up procedures and complete start-up checks according to plant configurations and system requirements 2.2. Confirm plant is operational |
3. Mix reagents | 3.1. Safely mix reagents to required parameters 3.2. Continuously inspect plant and identify defects and potential problems |
4. Add reagents | 4.1. Add reagent according to specified dosage and recommended location 4.2. Complete all required written documentation clearly, concisely and on time |
5. Transfer and store reagents | 5.1 Transfer reagents 5.2. Store reagents in approved storage facility 5.3. Confirm sufficient quantities of reagents are maintained |
6. Shutdown in sequence and/or isolate equipment | 6.1. Shutdown or isolate equipment in sequence 6.2. Perform post shutdown or isolation checks 6.3. Communicate end of shift information verbally or in writing to oncoming shift |
7. Conduct housekeeping activities | 7.1. Clean and check tools and equipment 7.2. Maintain and store tools and equipment |
Evidence is required to be collected that demonstrates a candidate’s competency in this unit. Evidence must be relevant to the roles within this sector’s work operations and satisfy all of the requirements of the performance criteria of this unit and include evidence that the candidate:
locates and applies applicable, documentation, policies and procedures
implements requirements, procedures and techniques for the safe, effective handling of reagents activities including:
performing pre-start checks
diagnosing faults, identifying and addressing hazards
selecting and using lifting equipment (manual, cranes and loads)
using and selecting appropriate tools and equipment
identify and select safe work practices
works effectively with others to undertake and complete the handling of reagents that meets all of the required outcomes including:
using a range of communications techniques and equipment to convey information to others
maintaining written and verbal reporting requirements and procedures
communicating to confirm work/plans/specifications
passing on end of shift information
demonstrates completion of the handling of reagents that safely, effectively and efficiently meets all of the required outcomes on more than one (1) occasion including:
performing correct sequencing for starting up equipment
correctly operating and monitoring equipment including:
inspecting operations/plant
selecting, mix and add reagents to required parameters and specified dosage
transferring and storing reagents
inspecting plant and identify defects and potential problems
performing shutdown and isolation checks in sequence
The candidate must demonstrate knowledge in Handle reagents activities through:
identifying and managing risks and hazards
identifying, addressing and reporting environmental issues setting up work activity
complying with isolation and breakdown procedures and responsibilities
complying with work health and safety practices
complying with emergency procedures
maintaining equipment safety requirements
applying waste procedures
carrying out work according to reagents handling principles and systems
complying with WHS procedures
using operational procedures and checks
applying site safety requirements
applying hazardous goods and consequences of spills procedures
complying with site procedures
applying site safety requirements
selecting and checking for faults, tools and equipment to carry out tasks
monitoring operations
reporting defects
applying safe work practices
identifying contaminant
identifying and complying with equipment limitations and maintaining operating parameters
complying with equipment safety requirements
identifying repair requirements
applying isolation procedures
interpreting and applying metallurgical and technical data (basic)
applying operational procedures and checks
An assessor of this unit must satisfy the requirements of the NVR/AQTF or their successors; and Industry regulations for certification and licensing; and,
this unit must be assessed in the context of this sector’s work environment; and,
this unit must be assessed in compliance with relevant legislation/regulation and using policies, procedures, processes and operational manuals directly related to the industry sector for which it is being assessed; and,
assessment may be conducted in conjunction with the assessment of other Units of Competency; and,
assessment must confirm consistent performance can be applied in a range of relevant workplace circumstances; and,
assessors must demonstrate the performance evidence, and knowledge evidence as outlined in this Unit of Competency, and through the minimum years of current* work experience specified below in an Industry sector relevant to the outcomes of the unit; or,
where the assessor does not meet experience requirements a co-assessment or partnership arrangement must exist between the qualified assessor and an Industry subject matter expert. The Industry subject matter expert should hold the unit being assessed (or an equivalent unit) and/or demonstrate equivalence of skills and knowledge at the unit level. An Industry technical expert must also demonstrate skills and knowledge from the minimum years of current work experience specified below in the Industry sector, including time spent in roles related to the unit being assessed; and,
assessor and Industry subject matter expert requirements differ depending on the Australian Qualifications Framework Level (AQF) of the qualification being assessed and/or Industry Sector as follows:
Industry sector | AQF** Level | Required assessor or Industry subject matter expert experience |
Drilling, Metalliferous Mining, Coal Mining, Extractive (Quarrying) and Civil Construction | 1 | 1 Year |
2 | 2 Years |
Drilling, Coal Mining and Extractive (Quarrying) | 3-6 | 3 Years |
Metalliferous Mining and Civil Construction | 3-6 | 5 Years |
Other sectors | Where this Unit is being assessed outside of the Resources and Infrastructure Sectors assessor and/or Industry subject matter expert experience should be in-line with industry standards for the sector in which it is being assessed and where no Industry standard is specified should comply with any relevant regulation. |
*Assessors can demonstrate current work experience through employment within Industry in a role relevant to the outcomes of the Unit; or, for external assessors this can be demonstrated through exposure to Industry by conducting frequent site assessments across various locations.
**Where a unit is being delivered outside of a Qualification the first numeric character in the Unit code should be considered to indicate the AQF level