Assessor Resource

UEGNSG806
Maintain SCADA controlled flow and pressure equipment and electronic gas measurement equipment

Assessment tool

Version 1.0
Issue Date: May 2024


This unit involves the skills and knowledge required to maintain supervisory control and data acquisition system (SCADA) controlled gas distribution and transmission station facilities in accordance with relevant legislation, codes of practice, regulations and workplace procedures.

It includes gas station maintenance of equipment, including remotely operated and controlled valves, air loaded and SCADA controlled regulators, Coriolis, and ultrasonic and electronic meters.

This unit applies to the following types of gas stations, subject to work health and safety (WHS)/occupational health and safety (OHS) and duty of care requirements being met for the workplace:

compressor stations

custody transfer stations

inlets and city gates

scraper stations

gas storage facilities

SCADA controlled main line valves

The skills and knowledge described in this unit require a licence or permit to practice in the workplace where work is carried out on electrical installations which are designed to operate at voltages greater than 50 V a.c. or 120 V d.c.

Competency development activities in this unit are subject to regulations directly related to licencing.

Additional and/or other conditions may apply in some jurisdictions subject to regulations related to electrical work. Practice in the workplace and during training is also subject to WHS/OHS regulations.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)


Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Range is restricted to essential operating conditions and any other variables essential to the work environment.

Non-essential conditions may be found in the UEG Gas Industry Training Package Companion Volume Implementation Guide.

equipment must include the following:

remotely operated valves, types: double block and bleed

remote telemetry units (RTU’s) and controllers

actuators: pneumatic, electric and I To P convertors

pressure controllers

meters: Coriolis and ultrasonic

Note: Fault finding is limited to the component level.

constants and variables must include the following:

monitoring, adjusting and controlling

regulation of flow and pressure

gas measurement

recording and reporting

regulation of the system

equipment

organisational and statutory requirements

third-party issues referred to appropriate person/s must include the following:

low voltage electrical work

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
WHS/OHS and environmental control measures for the gas station site are identified, obtained and applied 
 
 
 
 
 
 
 
 
 
 
 
WHS/OHS risk control measures, schedule of work and workplace procedures for carrying out work activities are followed 
 
 
 
 
 
 
 
 
 
 
 
 
 
WHS/OHS risk control work completion measures and procedures are followed 
 
 
 
 

Forms

Assessment Cover Sheet

UEGNSG806 - Maintain SCADA controlled flow and pressure equipment and electronic gas measurement equipment
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:


Assessment Record Sheet

UEGNSG806 - Maintain SCADA controlled flow and pressure equipment and electronic gas measurement equipment

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: