This unit involves the skills and knowledge required to install gas flow, measuring and pressure regulating devices in accordance with relevant legislation, codes of practice, regulations and workplace procedures.

It includes installing of gas valves, pressure controllers, regulators and meters in gas facilities and stations.

This unit applies to the following types of gas stations, subject to all work health and safety (WHS)/occupational health and safety (OHS) and duty of care requirements being met for the workplace:

pressure reduction stations, district and customer regulator sets

compressor stations

meter stations and customer meter sets

custody transfer stations

inlets and city gates

scraper stations

gas storage facilities

main line valves.

The skills and knowledge described in this unit require a licence or permit to practice in the workplace where work is carried out on electrical installations which are designed to operate at voltages greater than 50 V a.c. or 120 V d.c.

Competency development activities in this unit are subject to regulations directly related to licencing.

Additional and/or other conditions may apply in some jurisdictions subject to regulations related to electrical work. Practice in the workplace and during training is also subject to WHS/ OHS regulations.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Range is restricted to essential operating conditions and any other variables essential to the work environment. Non-essential conditions may be found in the UEG Gas Industry Training Package Companion Volume Implementation Guide.
work must be conducted in at least three (3) of the following types of gas facilities/stations:	district and customer metering and regulator sets distribution line and path valves pressure reduction stations, district and customer regulator sets compressor stations meter stations and customer meter sets custody transfer stations inlets and city gates scraper stations gas storage facilities non-supervisory control and data acquisition (SCADA) main line valves
equipment must include the following:	valves: manual, ball, plug, double black and bleed pressure controllers actuators at least two (2) types of regulators: diaphragm, sleeve and hydraulic plug at least two (2) types of meters: small capacity union connected positive displacement meters, diaphragm, rotary and turbine Note: fault finding is limited to the component level.
constants and variables must include the following:	monitoring, adjusting and controlling regulation of flow and pressure gas measurement recording and reporting regulation of the system equipment organisational and statutory requirements
third-party issues referred to appropriate person/s must include the following:	low voltage electrical work

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice	Yes	No	Comments/feedback
WHS/OHS and environmental control measures for the site are identified, obtained and applied
WHS/OHS risk control measures, schedule of work and workplace procedures for carrying out work are followed
WHS/OHS risk control, work completion measures and workplace procedures are followed

Assessment Cover Sheet

UEGNSG807 - Install gas flow, measuring and pressure regulating devices

Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

UEGNSG807 - Install gas flow, measuring and pressure regulating devices

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: