Assessor Resource

UEPOPS251A
Conduct routine wind turbine maintenance

Assessment tool

Version 1.0
Issue Date: March 2024


2)

This unit is intended to augment formally acquired competencies. It is suitable for employment-based programs under an approved contract of training.

1)Scope:

1.1) Descriptor

This unit deals with the skills and knowledge required to conduct a range of routine maintenance functions associated with wind turbines.

You may want to include more information here about the target group and the purpose of the assessments (eg formative, summative, recognition)

Prerequisites

Prerequisite Unit(s)

4)

Competencies

4.1)

Granting of competency in this unit shall be made only after competency in the following unit(s) has/have been confirmed.

Where pre-requisite pathways have been identified. All competencies in the Common Unit Group must be have been completed.

There are no prerequisite units.

Literacy and numeracy skills

4.2)

Participants are best equipped to achieve this unit if they have reading, writing and numeracy skills indicated by the following levels. A description of what each level entails is provided in Section 2.3.1 Language, Literacy and Numeracy.

Reading

2

Writing

2

Numeracy

2


Employability Skills

5)

The required outcomes described in this unit of competency contain applicable facets of Employability Skills. The Employability Skills Summary of the qualification in which this unit of competency is packaged will assist in identifying Employability Skill requirements.




Evidence Required

List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.

9) This provides essential advice for assessment of the competency standard unit and must be read in conjunction with the Performance Criteria and the Range Statement of the competency standard unit and the Training Package Assessment Guidelines.

The Evidence Guide forms an integral part of this competency standard unit and shall be used in conjunction with all components parts of this unit and, performed in accordance with the Assessment Guidelines of this Training Package.

Overview of Assessment

9.1)

Longitudinal competency development approaches to assessment, such as Profiling, require data to be reliably gathered in a form that can be consistently interpreted over time. This approach is best utilised in Apprenticeship programs and reduces assessment intervention. It is the Industry’s preferred model for apprenticeships. However, where summative (or final) assessment is used it is to include the application of the competency in the normal work environment or, at a minimum, the application of the competency in a realistically simulated work environment. It is recognised that, in some circumstances, assessment in part or full can occur outside the workplace. However, it must be in accord with Industry and, Regulatory policy in this regard.

Methods chosen for a particular assessment will be influenced by various factors. These include the extent of the assessment, the most effective locations for the assessment activities to take place, access to physical resources, additional safety measures that may be required and the critical nature of the competencies being assessed.

The critical safety nature of working with electricity, electrical equipment, gas or any other hazardous substance/material carries risk in deeming a person competent. Hence, sources of evidence need to be ‘rich’ in nature to minimise error in judgment.

Activities associated with normal every day work have a bearing on the decision as to how much and how detailed the data gathered will contribute to its ‘richness’. Some skills are more critical to safety and operational requirements while the same skills may be more or less frequently practised. These points are raised for the assessors to consider when choosing an assessment method and developing assessment instruments. Sample assessment instruments are included for Assessors in the Assessment Guidelines of this Training Package.

Critical aspects of evidence required to demonstrate competency in this unit

9.2)

Before the critical aspects of evidence are considered all prerequisites shall be met.

Evidence for competence in this unit shall be considered holistically. Each Element and associated Performance Criteria shall be demonstrated on at least two occasions in accordance with the “Assessment Guidelines – UEP12”. Evidence shall also comprise:

A representative body of work performance demonstrated within the timeframes typically expected of the discipline, work function and industrial environment. In particular this shall incorporate evidence that shows a candidate is able to:

Implement Occupational Health and Safety workplace procedures and practices including the use of risk control measures as specified in the Performance Criteria and Range Statement

Apply sustainable energy principles and practices as specified in the Performance Criteria and Range Statement

Demonstrate an understanding of the Essential Knowledge and Associated Skills as described in 6) Essential Knowledge and Associated Skills of this unit

Demonstrate an appropriate level of employability skillsConduct work observing the relevant Anti-Discrimination legislation, regulations, polices and workplace procedures

Demonstrated performance across a representative range of contexts from the prescribed items below:

Knowledge and application of relevant sections of: Occupational, health and safety legislation; Statutory legislation; Enterprise/site safety procedures; Enterprise/site emergency procedures

Acquiring and analysing information relevant for recording

Maintaining records

Retrieving records

Dealing with an unplanned event by drawing on Essential Knowledge and Skills to provide appropriate solutions incorporated in the holistic assessment with the above listed items.

Context of and specific resources for assessment

9.3)

This unit should be assessed as it relates to normal work practice using procedures, information and resources typical of a workplace. This should include:

OHS policy and work procedures and instructions

Suitable work environment, facilities, equipment and materials to undertake actual work as prescribed by this competency standard unit

Competency Standards should be assessed in the workplace or simulated workplace and under the normal range of workplace conditions.

Assessment of this unit will be supported with documentary evidence, by means of endorsement stating type and application of work.

In addition to the resources listed above in Context of assessment’, evidence should show competency working in confined spaces, with different types of plant and equipment as well as different structural/construction types and method and in a variety of environments.

Method of assessment

9.4)

This unit shall be assessed by methods given in Section 1.3.00 Assessment Guidelines.

Note:

Competent performance with inherent safe working practices is expected in the Industry to which this competency standard unit applies. This requires that the specified Essential Knowledge and Associated Skills be assessed in a structured environment, which is primarily intended for learning/assessment and incorporates all necessary equipment and facilities for learners to develop and demonstrate the Essential Knowledge and Skills described in this unit.

Concurrent assessment and relationship with other units

9.5)

There are no recommended concurrent assessments with this unit, however in some cases efficiencies may be gained in terms of learning and assessment effort being concurrently managed with allied competency standard units where listed.

Nil


Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assingnment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)


Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

8) This describes the essential skills and knowledge and their level, required for this unit.

Evidence shall show that knowledge has been acquired of conducting routine wind turbine maintenance.

The extent of the Essential Knowledge and Associated Skills required follows:

KS01-PO251A Routine wind turbine maintenance

Evidence shall show that knowledge has been acquired for safe working practices of:

T1 Relevant Environmental, Occupational Health and Safety legislation and regulations

T2 Enterprise procedures

T3 Plant drawings and manufacturers manuals

T4 Introduction to and typical arrangements of wind farm power plant

T5 Relevant plant and equipment, its location and operating parameters

T6 Equipment and material required to perform the work

T7 Wind farm principles

T8 Wind turbine types and characteristics

T9 Routine maintenance techniques

T10 Hand and portable power tools

T11 Lubrication systems and oil conditioning systems

T12 Lifting techniques

T13 Working at heights principles

T14 Cleaning techniques

T15 Ladder safety

T16 Fitness requirements for climbing towers

KS02-PO251A Routine wind turbine maintenance

Specific skills needed to achieve the Performance Criteria:,

T1 Interpret plant drawings and manufacturers manuals

T2 Apply routine maintenance techniques

T3 Identify and select materials for the job

T4 Use hand and portable power tools

T5 Store and maintain tools and equipment

T6 Apply working at principles

10) This relates to the competency standard unit as a whole providing the range of contexts and conditions to which the Performance Criteria apply. It allows for different work environments and situations that will affect performance.

Routine maintenance may include lubrication, gland nipping, draining of water taps, filter cleaning and changing, greasing, filling of oil tanks, removing/replacing access covers, applying plastic metals, cleaning plant and equipment, degreasing, limited mechanical assembly, minor fabrication e.g. brackets, gaskets, changing globes and starters, switchboard indicator lenses, checking transformer oil levels, generator brush changes , changing of oil and air filters, cleaning of air and oil filters, battery inspection, recording of cell voltages.

Inspections should be planned with the appropriate parties to determine access, conditions and work requirements.

Materials may refer to lubricants, chemical, cleaning agents and emery paper.

Equipment may include pitch and yaw controls, pumps, fans, compressors, blowers, transmissions, pipe work, heat exchangers, tanks, printers, , recorders, battery cells, , generator brushes, air conditioners, transformers, switchboards and control panels.

Tools may include grease guns, hand tools, power tools and specialist tools.

Appropriate parties may refer to supervisor, tradesperson or operations personnel.

Work completion details and plans may include plant and maintenance records, job cards, check sheets, on device labelling updates and reporting and/or documenting equipment defects.

Work site environment may be affected by nearby plant or processes, e.g. chemical, heat, dust, noise, gas and oil.

Isolations can refer to electrical/mechanical or other associated processes.

Generic terms are used throughout this Training Package for vocational standard shall be regarded as part of the Range Statement in which competency is demonstrated. The definition of these and other terms are given in Section 2.1 Preliminary Information and Glossaries.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
Work requirements are identified from request/work orders or equivalent and clarified/confirmed with appropriate parties or by site inspection 
Occupational Health and Safety standards, statutory requirements, relevant Australian standards, codes of practice, manufacturers’ specifications, environmental requirements and enterprise procedures are identified, applied and monitored throughout the work procedure 
Resources required to satisfy the work plan are identified, obtained and inspected for compliance with the job specifications 
Relevant plans, drawings and texts are selected and interpreted in accordance with the work plan 
Correct size, type and quantity of materials/components are determined, obtained and inspected for compliance with the job specifications 
Work is planned in detail including sequencing and prioritising and considerations made, where appropriate, for the maintenance of plant security and capacity in accordance with system/site requirements 
Co-ordination requirements, including requests for isolations where appropriate, are resolved with others involved, affected or required by the work 
Potential hazards are identified and prevention and/or control measures are selected in accordance with the work plan and site procedures 
Work area is prepared in accordance with work requirements and site procedures 
Required isolations are confirmed where appropriate in accordance with enterprise requirements 
Routine maintenance is conducted in accordance with the work plan and site requirements 
Minor adjustments are undertaken in accordance with prescribed procedures and schedules and site requirements 
Faults are reported to the relevant parties in accordance with site/enterprise procedures 
Work is completed and appropriate personnel notified in accordance with site/enterprise requirements 
Work area is cleared of waste, cleaned, restored and secured in accordance with site/enterprise procedures 
Plant, tools and equipment are maintained and stored in accordance with site/enterprise procedures 
Work completion details are finalised in accordance with site/enterprise procedures 

Forms

Assessment Cover Sheet

UEPOPS251A - Conduct routine wind turbine maintenance
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:


Assessment Record Sheet

UEPOPS251A - Conduct routine wind turbine maintenance

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: