Google Links

Follow the links below to find material targeted to the unit's elements, performance criteria, required skills and knowledge

Elements and Performance Criteria

1. Plan the installation of pipework and pipework assemblies
   • Quantity and type of pipework and pipework assemblies are selected according to specifications.
   • The appropriate sequence for the installation of pipework and pipework assemblies is determined according to the installation type and specifications and other applicable factors.
   • The work area is prepared for installation of pipework and pipework assemblies.
2. Prepare pipework and pipework assemblies for assembly
   • Pipework is cleaned to standard operating procedures.
   • Pipework and assemblies are purged to standard operating procedures.
   • Pipework and assemblies are capped/sealed.
3. Install pipework and assemblies
   • Enclosures/hangers/support systems are installed without damage or distortion to the surrounding environment or other services.
   • Pipework and assemblies are installed without damage or distortion to pipework, assemblies or surrounding environment or other services.
   • Pipework is leak tested to standard operating procedures.
   • All ancillary devices and materials are installed to specification according to standard operating procedures.

Required Skills

Required skills

Look for evidence that confirms skills in interpreting and following information on specifications standard operating procedures and other applicable reference documents planning and sequencing installation preparing the site preparing joining surfaces purging pipework and assembly capping and sealing pipework and assembly installing enclosurehanging supporting assemblies assembling and installing pipework and ancillaries testing installed pipework and rectifying leaks

Required knowledge

Look for evidence that confirms knowledge of installation techniques site and safety requirements cleaning procedures and the applications and precautions for using solventscleaning material purging techniques applications and precautions cappingsealing pipework and assembly methods identification of locationlayout of pipework and assemblies and application and characteristics of enclosurehangingsupporting systems pipework ancillary installation and joining procedures leak testing applications and uses regulations and legislative requirements hazards and control measures use and application of personal protective equipment safe work practices and procedures

Evidence Required

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria required skills and knowledge range statement and the Assessment Guidelines for the Training Package
Overview of assessment	A person who demonstrates competency in this unit must be able to install pipework and pipework assemblies in accordance with standard operating procedures Competency in this unit cannot be claimed until all prerequisites have been satisfied
Critical aspects for assessment and evidence required to demonstrate competency in this unit	Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria including required knowledge and be capable of applying the competency in new and different situations and contexts
Context of and specific resources for assessment	This unit may be assessed on the job off the job or a combination of both on and off the job Where assessment occurs off the job that is the candidate is not in productive work then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team The assessment environment should not disadvantage the candidate This unit could be assessed in conjunction with any other units addressing the safety quality communication materials handling recording and reporting associated with installing pipework and pipework assemblies or other units requiring the exercise of the skills and knowledge covered by this unit
Method of assessment	Assessors should gather a range of evidence that is valid sufficient current and authentic Evidence can be gathered through a variety of ways including direct observation supervisors reports project work samples and questioning Questioning techniques should not require language literacy and numeracy skills beyond those required in this unit of competency The candidate must have access to all tools equipment materials and documentation required The candidate must be permitted to refer to any relevant workplace procedures product and manufacturing specifications codes standards manuals and reference materials
Guidance information for assessment

---

Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Pipework and pipework assemblies	Ferrous, non-ferrous, plastic, etc. Variety of sizes and or wall thickness Variety of joining systems such as collars, unions, flanges, etc.
Enclosures	Metal and PVC
Hangers and support systems	Pipe/tube bundle support, ties, unistrut, trays, ladder racks, ducts etc.
Leak test	Soapy water, water immersion, compressed air
Ancillary devices and materials	Insulation materials, valve control systems, etc.
Legislation and regulations	Building regulations, gas/fluid pipeline regulations

---