Google Links

Follow the links below to find material targeted to the unit's elements, performance criteria, required skills and knowledge

Elements and Performance Criteria

1. Prepare for work.
   • Identify work requirements
   • Identify and control hazards
   • Coordinate with appropriate personnel
2. Prepare equipment for operation.
   • Check operation and function of prime movers by applying principles of operation and procedures
   • Check the operational area to ensure that any potential hazards which may affect the operation of the equipment are removed
   • Conduct required safety checks and pre-starts to determine or verify the operational condition of the equipment.
3. Start up prime movers.
   • Commission and bring on line prime mover protection devices and ancillary equipment as required by start-up
   • Start up prime mover according to procedures.
4. Monitor and assess prime mover systems.
   • Monitor fuel, energy systems and flows as required for prime mover use
   • Ensure adequate supplies of clean air at the stated rate or temperature are delivered to the prime mover to allow for successful operation to be achieved
   • Monitor lubrication systems to verify that operational parts are functioning efficiently and effectively, and to ensure that all moving parts are operating in a friction free and clean environment
   • Monitor and adjust cooling systems to allow for the most efficient operating temperature to be maintained throughout all operating conditions
   • Monitor governing systems to allow correct operational speeds of equipment to be maintained and regulated.
   • Take appropriate action as a result of monitoring observations.
5. Monitor operational maintenance requirements.
   • Conduct routine inspections and checks to ensure normal or stated prime mover operation is maintained
   • Identify equipment faults through observation of the operational equipment and periodic sampling and testing
   • Take appropriate action on items found
   • Record operational data to provide a historical record of the operating condition of equipment.
6. Isolate and de-isolate plant.
   • Isolate plant
   • Make safe for required work
   • Check plant is ready to be returned to service
   • Prepare plant for return to service.

Required Skills

This describes the essential skills and knowledge and their level required for this unit

Required skills

efficient and effective operation of plantequipment hazard analysis completing plant records communication problem solving

Required knowledge

The knowledge referred to in the Evidence Guide for this unit includes all items on a schematic of the prime mover and the function of each prime mover operating parameters and capacities prime mover operating principles including fuel injection lubrication cooling ignition induction and exhaust power supply equipment operation including flows pressures temperatures and speeds equipment terminology sampling and testing techniques process drawings eg PID PFS cause and effect safety systems and procedures job hazard analysis physics and chemistry relevant to the prime mover process parameters and limits eg temperature pressure flow duty of care obligations hierarchy of control communication protocols eg radio phone computer paper permissionsauthorities routine problems faults and their resolution relevant alarms and actions plant process idiosyncrasies correct methods of starting stopping operating and controlling flow corrective action appropriate to the problem cause function and troubleshooting of major internal components and their problems

Evidence Required

The Evidence Guide provides advice on assessment and must be read in conjunction with the Performance Criteria Required Skills and Knowledge the Range Statement and the Assessment Guidelines for the Training Package
Overview of assessment	Assessment of this unit should include demonstrated competence on actual plant and equipment in a work environment The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency Assessment will occur over a range of situations which will include disruptions to normal smooth operation Simulation may be required to allow for assessment of parts of this unit Simulation should be based on the actual plant and will include walkthroughs of the relevant competency components Simulations may also include the use of case studiesscenarios role plays and D virtual reality interactive systems In the case of evacuation training or of training for competencies practised in life threatening situations simulation may be used for the bulk of the training This unit requires an application of the knowledge contained in the use of the prime movers and its integral equipment to the level needed to maintain control and recognise and resolve problems This can be assessed through questioning and the use of whatif scenarios both on the plant during demonstration of normal operations and walkthroughs of abnormal operations and off the plant
Critical aspects for assessment and evidence required to demonstrate competency in this unit	Competence must be demonstrated in the ability to recognise and analyse potential situations requiring action and then in implementing appropriate corrective action The emphasis should be on the ability to stay out of trouble rather than on recovery from a disaster Consistent performance should be demonstrated In particular look to see that early warning signs of equipmentprocesses needing attention or with potential problems are recognised the range of possible causes can be identified and analysed and the most likely cause determined appropriate action is taken to ensure a timely return to full performance obvious problems in related plant areas are recognised and an appropriate contribution made to their solution These aspects may be best assessed using a range of scenarioscase studieswhatifs as the stimulus with a walkthrough forming part of the response These assessment activities should include a range of problems including new unusual and improbable situations which may have been generated from the past incident history of the prime mover incidents on similar prime movers around the world hazard analysis activities and similar sources
Context of and specific resources for assessment	As a general rule assessment will require access to an operating plant over an extended period of time or a suitable method of gathering evidence of operating competence over a range of situations A bank of scenarioscase studieswhatifs will be required as will a bank of questions which will be used to probe the reasoning behind the observable actions
Method of assessment	In all plants it may be appropriate to assess this unit concurrently with relevant teamwork and communication units
Guidance information for assessment	Assessment processes and techniques must be culturally appropriate and appropriate to the oracy language and literacy capacity of the assessee and the work being performed

---

Range Statement

The Range Statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the Performance Criteria, is detailed below. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs if the candidate, accessibility of the item, and local industry and regional contexts.
Codes of practice/ standards	Where reference is made to industry codes of practice, and/or Australian/international standards, the latest version must be used.
Context	This unit of competency includes all such items of equipment and unit operations which form part of the production/processing system. For your plant this may include (select relevant items): diesel, gas and petrol reciprocating engines turbine engines electric motors governing systems power supply safety and shutdown systems cooling systems.
Problems	Typical problems for your plant may include: variation in power/fuel supply vibration overheating fouling of turbine/engine/exchangers lubrication quality ancillary equipment failures. prime mover failure or malfunction electrical failure or malfunction mechanical failure/malfunction equipment design deficiencies quality measurement inaccuracy, eg analyzer, manual sampling deficiencies fuel quality.
Appropriate action	Appropriate action includes: determining problems needing action determining possible fault causes rectifying problem using appropriate solution within area of responsibility following through items initiated until final resolution has occurred reporting problems outside area of responsibility to designated person.
Procedures	Procedures may be written, verbal, computer-based or in some other form. They include: all work instructions standard operating procedures formulas/recipes batch sheets temporary instructions any similar instructions provided for the smooth running of the plant. For the purposes of this Training Package, 'procedures' also includes good operating practice as may be defined by industry codes of practice (eg Responsible Care) and government regulations.
Health, safety and environment (HSE)	All operations to which this unit applies are subject to stringent health, safety and environment requirements, which may be imposed through State or Federal legislation, and these must not be compromised at any time. Where there is an apparent conflict between Performance Criteria and HSE requirements, the HSE requirements take precedence.

---