Google Links

Follow the links below to find material targeted to the unit's elements, performance criteria, required skills and knowledge

Elements and Performance Criteria

1. Develop mould design
   • Establish original product concept or design from drawings, originals or consultation with the customer
   • Sketch out product prototype design and establish product sizes making appropriate allowance for material shrinkage
   • Identify areas where undercuts, cutbacks or other special features are required
   • Determine parting line
   • Determine material from which mould is to be made
2. Select mould material and prepare for mould production
   • Set up material for mould making, ensuring that the mould can be handled or moved without damage
   • Establish datum point and mark out design dimensions using geometric and lineal calculations
   • Determine correct cavity depths and contours
   • Ensure there is adequate ventilation and light to facilitate an appropriate work environment
3. Produce working mould
   • Fit appropriate protective equipment to prevent inhalation or irritation of by-products of the mould making process
   • Use appropriate tools to carve out mould cavity and detail
   • Accurately follow the design detail to produce a mould cavity to specification
   • Avoid undercuts which will prevent removal of the plaster product from the mould
   • Ensure appropriate degrees of taper are provided to facilitate product removal
   • Carve reliefs according to design and remove debris as the work proceeds
4. Complete mould
   • Clean down completed mould and clean up work area
   • Inspect mould surface for defects or irregularities
   • Compare design details with mould cavity to confirm accuracy of translation
   • Coat mould surface to preserve finish and allow to dry
5. Produce product prototype
   • Apply slipping agent to mould surface
   • Prepare and insert anchors or ties
   • Prepare plaster mixture and appropriate amount of glass fibre
   • Cast plaster mix and fibre into mould cavity, strike off and allow to set
   • Remove prototype from mould or mould from prototype
   • Check prototype for dimensional and detail accuracy
   • Compare prototype and mould to identify any faults or mould inaccuracies
   • Adjust or dress mould to remove imperfections and clean mould surface
   • Cast second prototype and recheck product and mould
   • Clean up mould and mark in accordance with organisation identification practice
6. Control hazards
   • Identify hazards in modelling work area
   • Assess the risks arising from those hazards
   • Implement measures to control those risks in line with procedures and duty of care
7. Respond to problems
   • Identify possible routine and non-routine problems in the equipment or process
   • Determine problems needing action
   • Determine possible fault causes
   • Rectify problem using appropriate solution within area of responsibility
   • Report problems outside area of responsibility to designated person

Required Skills

Required skills

Required skills include using and maintaining all required materials tools and parts recognising situations which could cause production problems and taking appropriate action implementing enterprises procedures and relevant regulatory requirements within appropriate time constraints and in a manner relevant to the operation of moulds and dies diagnosing and solving problems involved in the work communicating effectively with team members management and other departments reading and numeracy to interpret workplace documents and technical information

Required knowledge

Required knowledge includes specified quality standards characteristics of different materials requirements from drawings specifications or job sheets distinguish between causes of faults such as materials faults dimensional inaccuracies inappropriate allowance for material shrinkage damage to components

Evidence Required

The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria required skills and knowledge range statement and the Assessment Guidelines for the Training Package
Overview of assessment	The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency
Critical aspects for assessment and evidence required to demonstrate competency in this unit	Competence must be demonstrated in the ability to recognise situations requiring action and then in implementing appropriate corrective action Consistent performance should be demonstrated In particular look to see that OHS requirements are met quality improvement techniques are applied emergency procedures are understood and applied waste is minimised
Context of and specific resources for assessment	Assessment will require access to an operating plant over an extended period of time or a suitable method of gathering evidence of operating ability over a range of situations Assessment will occur over a range of situations which will include disruptions to normal smooth operation Simulation or case studiesscenarios may be required to allow for timely assessment of parts of this unit of competency Simulation should be based on the actual plant and will include walkthroughs of the relevant competency components A bank of scenarioscase studieswhat ifs and questions will be required to probe the reasoning behind observable actions
Method of assessment	In all plants it may be appropriate to assess this unit concurrently with relevant teamwork and communication units
Guidance information for assessment	Assessment processes and techniques must be culturally appropriate and appropriate to the language and literacy capacity of the candidate and the work being performed

---

Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Procedures	All operations are performed in accordance with standard procedures and work instructions
Moulds	Moulds may be manufactured from: plaster timber rubber metal a combination of these
Materials	Materials may include: additives body materials epoxy resins metal strapping plaster release agents rubber timber water
Equipment	Equipment may include: moulds chisels and hand held cutting tools hand and power tools jigs and fixtures personal safety equipment mixing equipment models weighing equipment
Typical problems	Typical problems may include: personal injuries complexities of mould design and shape lack of appropriate illumination
Occupational health and safety (OHS)	The identification and control of hazards and the application of OHS are to be in accordance with current, applicable legislation and regulations, and company procedures. All work is carried out at all times in accordance with these requirements

---