Google Links

Follow the links below to find material targeted to the unit's elements, performance criteria, required skills and knowledge

Elements and Performance Criteria

1. Design and make models
   • Establish model design from drawings, originals or in consultation with the customer
   • Select and prepare appropriate materials for model construction
   • Make models ensuring the final product is to specification, and shrinkage is allowed for
2. Set up and produce block moulds
   • Select appropriate model to meet specification
   • Determine required sections and parting lines
   • Check mould meets occupational health and safety (OHS) needs
   • Mix materials as required
   • Fill mould with mould material as required
   • Remove mould from model when required strength has been achieved
   • Finish mould to specifications and register correctly
3. Prepare cases and frames
   • Consult manufacturing schedule to determine type of mould to be made
   • Select appropriate frame or frames
   • Mix materials as required
   • Fill block mould
   • Remove block mould from the case and frame when required strength has been obtained
   • Register and date cases according to procedures
   • Prepare block mould for use
4. Prepare and make working moulds
   • Select the appropriate case/frame
   • Mix and pour mould material as required
   • Remove mould from model when required strength has been obtained
   • Finish and register moulds to procedures
   • Stack and dry moulds to procedures
   • Store moulds to procedures
5. Prepare dies
   • Consult manufacturing schedule to determine type of die to be made
   • Select and prepare required master die
   • Mix and pour die material as required
   • Remove die from master die when required strength has been obtained
   • Mark and finish dies to enterprise specifications
   • Cure and store dies to procedures
6. Respond to problems
   • Identify possible routine and non-routine problems in the equipment or process
   • Determine problems needing action
   • Determine possible fault causes
   • Rectify problem using appropriate solution within area of responsibility
   • Report problems outside area of responsibility to designated person

Required Skills

Required skills

Required skills include using and maintaining all required materials tools and parts recognising situations which could cause production problems and taking appropriate action implementing enterprises procedures and relevant regulatory requirements within appropriate time constraints and in a manner relevant to the operation of moulds and dies diagnosing and solving problems involved in the work predicting hazards that may arise from mould or die design or preparation communicating effectively with team members management and other departments reading and numeracy to interpret workplace documents and technical information

Required knowledge

Required knowledge includes specified quality standards characteristics of different materials requirements from drawings specifications or job sheets distinguish between causes of faults such as materials dimensions allowance for shrinkage damage to components

Evidence Required

The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria required skills and knowledge range statement and the Assessment Guidelines for the Training Package
Overview of assessment	The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency
Critical aspects for assessment and evidence required to demonstrate competency in this unit	Competence must be demonstrated in the ability to recognise situations requiring action and then in implementing appropriate corrective action Consistent performance should be demonstrated In particular look to see that OHS requirements are met quality improvement techniques are applied emergency procedures are understood and applied waste is minimised
Context of and specific resources for assessment	Assessment will require access to an operating plant over an extended period of time or a suitable method of gathering evidence of operating ability over a range of situations Assessment will occur over a range of situations which will include disruptions to normal smooth operation Simulation or case studiesscenarios may be required to allow for timely assessment of parts of this unit of competency Simulation should be based on the actual plant and will include walkthroughs of the relevant competency components A bank of scenarioscase studieswhat ifs and questions will be required to probe the reasoning behind observable actions
Method of assessment	This unit has no prerequisite competencies Individual enterprises may choose to add prerequisites and corequisites relevant to their processes
Guidance information for assessment	Assessment processes and techniques must be culturally appropriate and appropriate to the language and literacy capacity of the candidate and the work being performed

---

Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Procedures	All operations are performed in accordance with standard procedures and work instructions
Materials	Materials may include: additives body materials epoxy resins metal strapping plaster plastic release agents rubber slip timber water
Equipment	Equipment may include: block moulds and working moulds cases and frames hand and power tools jigs and fixtures master dies mixing equipment models weighing equipment
OHS	The identification and control of hazards and the application of OHS are to be in accordance with current, applicable legislation and regulations, and company procedures. All operations are subject to stringent OHS requirements and these must not be compromised at any time. Where there is an apparent conflict between performance criteria and OHS requirements, the OHS requirements take precedence

---