Subjects
To be awarded the six (6) core units of competency fourteen (14) elective units of competency from Groups A and B, chosen as specified below. A minimum of one (1) unit must be selected from Group A The balance of units, to a maximum of thirteen (13), may be chosen from Groups A and B, with a maximum of nine (9) from Group B2. Up to six (6) of the elective units of competency can be chosen from other qualifications in this Training Package, other endorsed Training Packages and accredited courses, as specified in Groups B1 and B2. Note: Where prerequisite units apply, they must be counted in the total number of units required for achievement of the qualification. | ||
Core units of competency | ||
Unit code | Unit title | |
Participate in environmentally sustainable work practices | ||
Work safely | ||
Apply workplace procedures | ||
Clean workplace or equipment | ||
Communicate in the workplace | ||
Select one (1) of the following units. Note that only | ||
Unit code | Unit title | Prerequisites |
Make measurements | ||
Read dials and indicators | ||
Elective units of competency Group A - Specialist electives | ||
Unit code | Unit title | Prerequisites |
Perform physical tests | ||
Operate process control systems | ||
Set up and tune a process | ||
Process raw meal into product | ||
Prepare moulds and dies | ||
Set up and tune glazing equipment | ||
Set up and optimise glass forming process | ||
Set up and optimise glass furnace process | ||
Set up and optimise secondary process | ||
Produce architectural precast concrete | ||
Produce structural precast concrete | ||
Design and construct moulds for fibrous plaster products | ||
Model fibrous plaster products | ||
Set up and optimise finishing process | ||
Group B - Other electives Group B1 | ||
Unit code | Unit title | Prerequisites |
Interpret technical drawing | ||
Facilitate the implementation of OHS for a work group | ||
Issue work permits | ||
Identify and implement opportunities to maximise production efficiencies | ||
Identify equipment faults | ||
Contribute to development of plant documentation | ||
Develop and adjust a production schedule | ||
Provide coaching/mentoring in the workplace | ||
Use structured problem solving tools | ||
Perform basic tests | ||
Carry out stock control | ||
Contribute to assessment | ||
Provide work skill instruction | ||
Up to two (2) relevant units may be chosen from this Training Package, other endorsed Training Packages and accredited courses where those units are available at Certificate III or IV. | ||
Group B2 | ||
Unit code | Unit title | Prerequisites |
Conduct local risk control | ||
Apply cost factors to work practices | ||
Interpret product costs in terms of customer requirements | ||
Apply 5S procedures | ||
Monitor process capability | ||
Apply quality standards | ||
Use planning software systems in operations | ||
Undertake root cause analysis | ||
Contribute to the application of a proactive maintenance strategy | ||
Follow emergency response procedures | ||
Use equipment | ||
Operate equipment | ||
Use enterprise computers or data systems | ||
Work in accordance with an issued permit | ||
Monitor and control work permits | ||
Observe permit work | ||
Enter confined space | ||
Work in a team | ||
Achieve work outcomes | ||
Process and record information | ||
Monitor process operations | ||
Undertake minor maintenance | ||
Manage conflict at work | ||
Sample and test materials and product | ||
Collect routine site samples | ||
Select and prepare materials | ||
Operate local control system | ||
Shift materials safely by hand | ||
Operate equipment to blend/mix materials | ||
Operate grinding equipment | ||
Prepare for production | ||
Process greenware/green products | ||
Operate an autoclave | ||
Heat accelerate the curing of precast concrete | ||
Operate crushing equipment | ||
Operate a calcining kiln | ||
Operate slip casting equipment | ||
Operate manual glazing equipment | ||
Prepare materials for clay and ceramic production | ||
Finish products after firing | ||
Hand mould products | ||
Operate a firing kiln | ||
Operate extrusion equipment | ||
Operate pressing equipment | ||
Operate glass melting process | ||
Operate process ovens | ||
Operate blown insulation equipment | ||
Operate float forming equipment | ||
Operate fibre forming equipment | ||
Operate container forming equipment | ||
Operate glass printing equipment | ||
Operate primary annealing equipment | ||
Operate glass finishing equipment | ||
Operate on-line stacking and assembly equipment | ||
Schedule, cut and bend reinforcement | ||
Finish green concrete products | ||
Cast moulded concrete products | ||
Finish cured concrete products | ||
Spin concrete pipes | ||
Conduct benching operations | ||
Assemble, fabricate and place reinforcement | ||
Finish casting operation | ||
Demould concrete products | ||
Batch mix concrete | ||
Deliver concrete to site | ||
Prepare asphalt | ||
Operate forming equipment | ||
Produce fibrous plasterboard | ||
Use and maintain tools and equipment for refractory operations | ||
Prepare for, install and repair refractory brickwork/blockwork | ||
Prepare for and install mouldable refractory materials | ||
Prepare for and cast refractory materials | ||
Prepare for and apply shotcrete for installation | ||
Store materials for production | ||
Organise self | ||
Move materials | ||
Operate bulk materials handling equipment | ||
Deliver customer service | ||
Allocate and complete team tasks | ||
Drive medium rigid vehicle | ||
Drive heavy rigid vehicle | ||
Operate a forklift | ||
Note: Only one of Up to four (4) relevant units may be selected from this Training Package, other endorsed Training Packages and accredited courses, where those units are packaged in Certificates II, III or IV. | ||
