Unit of Competency Mapping – Information for Teachers/Assessors – Information for Learners

AUMATK007 Mapping and Delivery Guide
Install vehicle plant, equipment and systems

Version 1.0
Issue Date: April 2024


Qualification -
Unit of Competency AUMATK007 - Install vehicle plant, equipment and systems
Description
Employability Skills
Learning Outcomes and Application This unit describes the performance outcomes required to install the plant, equipment and systems required for the design, development and production of motor vehicles.It applies to those in an automotive manufacturing environment.No licensing, legislative or certification requirements apply to this unit at the time of publication.
Duration and Setting X weeks, nominally xx hours, delivered in a classroom/online/blended learning setting.
Prerequisites/co-requisites
Competency Field Common
Development and validation strategy and guide for assessors and learners Student Learning Resources Handouts
Activities 		Slides
PPT 		Assessment 1 Assessment 2 Assessment 3 Assessment 4
Elements of Competency Performance Criteria              
Element: Prepare for installation
  • Installation instructions and work plans are identified and confirmed with appropriate personnel and installation requirements are determined
  • Parts, plant and equipment required for installation are obtained according to workplace procedures and within scope of responsibilities
  • Workplace procedures for installing vehicle plant, equipment and systems are identified
  • Work site is prepared according to installation plan and requirements of the manufacturer of the component parts, plant and equipment
  • Compliance of prepared work site with design drawings, work specifications, and work health and safety (WHS) requirements is determined
       
Element: Conduct installation
  • Pre-installation of parts, plant, equipment, fixtures and additional low voltage wiring is completed according to the installation plan and work specifications
  • Parts, plant, equipment, fixtures and additional low voltage wiring are installed according to installation plan and work specifications
  • Parts, plant, equipment, fixtures and additional low voltage wiring installations are checked against technical and safety requirements
       
Element: Finalise installation
  • Installation is checked against design specifications, workplace quality standards, manufacturer instructions and WHS requirements
  • Installation faults are reported and rectified according to workplace procedures
  • Installation reports are completed according to workplace procedures
       


Evidence Required

List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.

Elements

Performance Criteria

Elements describe the essential outcomes

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold italicised text is used, further information is detailed in the range of conditions section

1. Prepare for installation

1.1 Installation instructions and work plans are identified and confirmed with appropriate personnel and installation requirements are determined

1.2 Parts, plant and equipment required for installation are obtained according to workplace procedures and within scope of responsibilities

1.3 Workplace procedures for installing vehicle plant, equipment and systems are identified

1.4 Work site is prepared according to installation plan and requirements of the manufacturer of the component parts, plant and equipment

1.5 Compliance of prepared work site with design drawings, work specifications, and work health and safety (WHS) requirements is determined

2. Conduct installation

2.1 Pre-installation of parts, plant, equipment, fixtures and additional low voltage wiring is completed according to the installation plan and work specifications

2.2 Parts, plant, equipment, fixtures and additional low voltage wiring are installed according to installation plan and work specifications

2.3 Parts, plant, equipment, fixtures and additional low voltage wiring installations are checked against technical and safety requirements

3. Finalise installation

3.1 Installation is checked against design specifications, workplace quality standards, manufacturer instructions and WHS requirements

3.2 Installation faults are reported and rectified according to workplace procedures

3.3 Installation reports are completed according to workplace procedures

Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assignment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Elements

Performance Criteria

Elements describe the essential outcomes

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold italicised text is used, further information is detailed in the range of conditions section

1. Prepare for installation

1.1 Installation instructions and work plans are identified and confirmed with appropriate personnel and installation requirements are determined

1.2 Parts, plant and equipment required for installation are obtained according to workplace procedures and within scope of responsibilities

1.3 Workplace procedures for installing vehicle plant, equipment and systems are identified

1.4 Work site is prepared according to installation plan and requirements of the manufacturer of the component parts, plant and equipment

1.5 Compliance of prepared work site with design drawings, work specifications, and work health and safety (WHS) requirements is determined

2. Conduct installation

2.1 Pre-installation of parts, plant, equipment, fixtures and additional low voltage wiring is completed according to the installation plan and work specifications

2.2 Parts, plant, equipment, fixtures and additional low voltage wiring are installed according to installation plan and work specifications

2.3 Parts, plant, equipment, fixtures and additional low voltage wiring installations are checked against technical and safety requirements

3. Finalise installation

3.1 Installation is checked against design specifications, workplace quality standards, manufacturer instructions and WHS requirements

3.2 Installation faults are reported and rectified according to workplace procedures

3.3 Installation reports are completed according to workplace procedures

This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Bold italicised wording, if used in the performance criteria, is detailed below.

Instructions must include:

installation and work plans

job sheets, job specifications and design drawings

manufacturer instructions for the use of equipment and materials

work plans

workplace procedures to install plant and equipment.

Installation requirements must include:

physical resources

staffing.

Workplace procedures must include:

quality and continuous improvement programs

recording and reporting installation outcomes

WHS requirements.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
Installation instructions and work plans are identified and confirmed with appropriate personnel and installation requirements are determined 
Parts, plant and equipment required for installation are obtained according to workplace procedures and within scope of responsibilities 
Workplace procedures for installing vehicle plant, equipment and systems are identified 
Work site is prepared according to installation plan and requirements of the manufacturer of the component parts, plant and equipment 
Compliance of prepared work site with design drawings, work specifications, and work health and safety (WHS) requirements is determined 
Pre-installation of parts, plant, equipment, fixtures and additional low voltage wiring is completed according to the installation plan and work specifications 
Parts, plant, equipment, fixtures and additional low voltage wiring are installed according to installation plan and work specifications 
Parts, plant, equipment, fixtures and additional low voltage wiring installations are checked against technical and safety requirements 
Installation is checked against design specifications, workplace quality standards, manufacturer instructions and WHS requirements 
Installation faults are reported and rectified according to workplace procedures 
Installation reports are completed according to workplace procedures 

Forms

Assessment Cover Sheet

AUMATK007 - Install vehicle plant, equipment and systems
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

AUMATK007 - Install vehicle plant, equipment and systems

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: