Unit of Competency Mapping – Information for Teachers/Assessors – Information for Learners

AURETR033 Mapping and Delivery Guide
Develop and apply network electronic control system modifications

Version 1.0
Issue Date: March 2024


Qualification -
Unit of Competency AURETR033 - Develop and apply network electronic control system modifications
Description
Employability Skills
Learning Outcomes and Application This unit describes the performance outcomes required to develop, apply and validate significant modifications to existing network electronic control systems in order to vary or enhance performance. These systems include two-wire high and low speed (CAN-bus) and single wire low speed (LIN-bus) network circuits. The unit involves identifying the modification requirement, developing the modification specifications, applying and testing the modification, and completing workplace processes and documentation. Significant and non-routine modifications are those that require compliance with Australian Design Rules and Vehicle Safety Bulletins.It applies to those working in the automotive service and repair industry. The network electronic control systems include those of agricultural machinery, heavy commercial vehicles, light vehicles, marine vessels, mobile plant machinery, motorcycles or outdoor power equipment.No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
Duration and Setting X weeks, nominally xx hours, delivered in a classroom/online/blended learning setting.

Assessors must satisfy NVR/AQTF assessor requirements.

Competency is to be assessed in the workplace or a simulated environment that accurately reflects performance in a real workplace setting.

Assessment must include direct observation of tasks.

Where assessment of competency includes third-party evidence, individuals must provide evidence that links them to the network electronic control systems that they have modified, e.g. repair orders.

Assessors must verify performance evidence through questioning on skills and knowledge to ensure correct interpretation and application.

The following resources must be made available:

automotive service repair workplace or simulated workplace

workplace instructions

manufacturer network electronic control system specifications

ADRs and VSBs relating to network electronic control system modifications

two different vehicles, vessels, machinery or equipment requiring network electronic control system modification

diagnostic equipment for network electronic control system modification, including scan tools and oscilloscopes

tools, equipment and materials appropriate for completing network electronic control system modifications.

Prerequisites/co-requisites
Competency Field Electrical
Development and validation strategy and guide for assessors and learners Student Learning Resources Handouts
Activities
Slides
PPT
Assessment 1 Assessment 2 Assessment 3 Assessment 4
Elements of Competency Performance Criteria              
Element: Identify and confirm the modification requirement
  • Job requirements are determined from workplace instructions
  • Reasons for the modification are identified and confirmed with appropriate persons
  • Modification options are identified and reported to appropriate persons according to workplace procedures
  • Hazards associated with the work are identified and risks are managed
  • Legal and safety impacts of the modification are considered, as required, according to regulatory requirements
       
Element: Develop and validate the modification specification
  • Manufacturer specifications for the existing network electronic control systems are sourced and interpreted
  • Criteria for selecting the modification method and evaluating the outcomes are identified and documented
  • Proposed modification method is identified, selected and evaluated from available options
  • Selected option, including material choices and processes, is developed in detail and progressively assessed against established criteria
  • Modification specification is documented according to workplace procedures
       
Element: Apply and test the modification specification
  • Tools, test equipment and materials required to support the modification procedure are identified, selected and prepared for use
  • Selected modification method is carried out according to workplace procedures and safety requirements
  • Post-modification testing is carried out according to workplace procedures to confirm modification outcomes are as intended, and any problems detected as having been introduced during the modification process are rectified
  • Test results and other diagnostic findings are verified, as required, by using reliable alternative or optional processes
  • Variations needed during the modification process or as a result of testing are incorporated into the modification specification
  • Information and detail relating to the modification are documented and provided to the appropriate parties according to regulatory and commercial obligations
       
Element: Complete work processes
  • Final inspection is made to ensure work is to workplace expectations
  • Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
  • Tools and equipment are checked and stored, and any faulty electrical equipment is identified, tagged and isolated according to workplace procedures
  • Workplace documentation is processed according to workplace procedures
       
Element: Identify and confirm the modification requirement
  • Job requirements are determined from workplace instructions
  • Reasons for the modification are identified and confirmed with appropriate persons
  • Modification options are identified and reported to appropriate persons according to workplace procedures
  • Hazards associated with the work are identified and risks are managed
  • Legal and safety impacts of the modification are considered, as required, according to regulatory requirements
       
Element: Develop and validate the modification specification
  • Manufacturer specifications for the existing network electronic control systems are sourced and interpreted
  • Criteria for selecting the modification method and evaluating the outcomes are identified and documented
  • Proposed modification method is identified, selected and evaluated from available options
  • Selected option, including material choices and processes, is developed in detail and progressively assessed against established criteria
  • Modification specification is documented according to workplace procedures
       
Element: Apply and test the modification specification
  • Tools, test equipment and materials required to support the modification procedure are identified, selected and prepared for use
  • Selected modification method is carried out according to workplace procedures and safety requirements
  • Post-modification testing is carried out according to workplace procedures to confirm modification outcomes are as intended, and any problems detected as having been introduced during the modification process are rectified
  • Test results and other diagnostic findings are verified, as required, by using reliable alternative or optional processes
  • Variations needed during the modification process or as a result of testing are incorporated into the modification specification
  • Information and detail relating to the modification are documented and provided to the appropriate parties according to regulatory and commercial obligations
       
Element: Complete work processes
  • Final inspection is made to ensure work is to workplace expectations
  • Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected
  • Tools and equipment are checked and stored, and any faulty electrical equipment is identified, tagged and isolated according to workplace procedures
  • Workplace documentation is processed according to workplace procedures
       


Evidence Required

List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.

Elements

Elements describe the essential outcomes.

Performance Criteria

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.

1. Identify and confirm the modification requirement

1.1 Job requirements are determined from workplace instructions

1.2 Reasons for the modification are identified and confirmed with appropriate persons

1.3 Modification options are identified and reported to appropriate persons according to workplace procedures

1.4 Hazards associated with the work are identified and risks are managed

1.5 Legal and safety impacts of the modification are considered, as required, according to regulatory requirements

2. Develop and validate the modification specification

2.1 Manufacturer specifications for the existing network electronic control systems are sourced and interpreted

2.2 Criteria for selecting the modification method and evaluating the outcomes are identified and documented

2.3 Proposed modification method is identified, selected and evaluated from available options

2.4 Selected option, including material choices and processes, is developed in detail and progressively assessed against established criteria

2.5 Modification specification is documented according to workplace procedures

3. Apply and test the modification specification

3.1 Tools, test equipment and materials required to support the modification procedure are identified, selected and prepared for use

3.2 Selected modification method is carried out according to workplace procedures and safety requirements

3.3 Post-modification testing is carried out according to workplace procedures to confirm modification outcomes are as intended, and any problems detected as having been introduced during the modification process are rectified

3.4 Test results and other diagnostic findings are verified, as required, by using reliable alternative or optional processes

3.5 Variations needed during the modification process or as a result of testing are incorporated into the modification specification

3.6 Information and detail relating to the modification are documented and provided to the appropriate parties according to regulatory and commercial obligations

4. Complete work processes

4.1 Final inspection is made to ensure work is to workplace expectations

4.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected

4.3 Tools and equipment are checked and stored, and any faulty electrical equipment is identified, tagged and isolated according to workplace procedures

4.4 Workplace documentation is processed according to workplace procedures

Before competency can be determined, individuals must demonstrate they can perform the following according to the standard defined in this unit’s elements, performance criteria, range of conditions and foundation skills:

develop and apply one of the following significant and non-routine modifications on the network electronic control system of two different vehicles, vessels, machinery or equipment:

adapt or modify network electronic control system to a significantly changed capability

adapt network electronic control system for different work conditions

modify or install a significant network electronic control system for a special purpose.

Individuals must be able to demonstrate knowledge of:

work health and safety (WHS) and occupational health and safety (OHS) requirements relating to developing and applying network electronic control system modifications, including procedures for:

identifying hazards and controlling risks associated with wearing jewellery while working around high current wiring systems

using personal protective equipment (PPE) and hand tools

location and content of manufacturer specifications, workplace procedures and other relevant technical information relating to modifying network electronic control systems

principles and processes involved in planning and implementing modifications to network electronic control systems

types, functions, operation and limitations of the main automotive industry network electronic control systems being modified

types, functions, operation and limitations of diagnostic testing equipment required for network electronic control system modifications, including scan tools and oscilloscopes

requirements of Australian Design Rules (ADRs) and Vehicle Safety Bulletins (VSBs) relating to network electronic control system modifications

procedures for documenting and reporting the modification specifications and outcomes.


Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assignment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)


Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Elements

Elements describe the essential outcomes.

Performance Criteria

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold and italicised text is used, further information is detailed in the range of conditions section.

1. Identify and confirm the modification requirement

1.1 Job requirements are determined from workplace instructions

1.2 Reasons for the modification are identified and confirmed with appropriate persons

1.3 Modification options are identified and reported to appropriate persons according to workplace procedures

1.4 Hazards associated with the work are identified and risks are managed

1.5 Legal and safety impacts of the modification are considered, as required, according to regulatory requirements

2. Develop and validate the modification specification

2.1 Manufacturer specifications for the existing network electronic control systems are sourced and interpreted

2.2 Criteria for selecting the modification method and evaluating the outcomes are identified and documented

2.3 Proposed modification method is identified, selected and evaluated from available options

2.4 Selected option, including material choices and processes, is developed in detail and progressively assessed against established criteria

2.5 Modification specification is documented according to workplace procedures

3. Apply and test the modification specification

3.1 Tools, test equipment and materials required to support the modification procedure are identified, selected and prepared for use

3.2 Selected modification method is carried out according to workplace procedures and safety requirements

3.3 Post-modification testing is carried out according to workplace procedures to confirm modification outcomes are as intended, and any problems detected as having been introduced during the modification process are rectified

3.4 Test results and other diagnostic findings are verified, as required, by using reliable alternative or optional processes

3.5 Variations needed during the modification process or as a result of testing are incorporated into the modification specification

3.6 Information and detail relating to the modification are documented and provided to the appropriate parties according to regulatory and commercial obligations

4. Complete work processes

4.1 Final inspection is made to ensure work is to workplace expectations

4.2 Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected

4.3 Tools and equipment are checked and stored, and any faulty electrical equipment is identified, tagged and isolated according to workplace procedures

4.4 Workplace documentation is processed according to workplace procedures

This section specifies work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Bold italicised wording, if used in the performance criteria, is detailed below.

Safety requirements must include:

work health and safety (WHS) and occupational health and safety (OHS) requirements, including procedures for:

identifying hazards and controlling risks associated with wearing jewellery while working around high current wiring systems

using personal protective equipment (PPE) and hand tools.

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
Job requirements are determined from workplace instructions 
Reasons for the modification are identified and confirmed with appropriate persons 
Modification options are identified and reported to appropriate persons according to workplace procedures 
Hazards associated with the work are identified and risks are managed 
Legal and safety impacts of the modification are considered, as required, according to regulatory requirements 
Manufacturer specifications for the existing network electronic control systems are sourced and interpreted 
Criteria for selecting the modification method and evaluating the outcomes are identified and documented 
Proposed modification method is identified, selected and evaluated from available options 
Selected option, including material choices and processes, is developed in detail and progressively assessed against established criteria 
Modification specification is documented according to workplace procedures 
Tools, test equipment and materials required to support the modification procedure are identified, selected and prepared for use 
Selected modification method is carried out according to workplace procedures and safety requirements 
Post-modification testing is carried out according to workplace procedures to confirm modification outcomes are as intended, and any problems detected as having been introduced during the modification process are rectified 
Test results and other diagnostic findings are verified, as required, by using reliable alternative or optional processes 
Variations needed during the modification process or as a result of testing are incorporated into the modification specification 
Information and detail relating to the modification are documented and provided to the appropriate parties according to regulatory and commercial obligations 
Final inspection is made to ensure work is to workplace expectations 
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected 
Tools and equipment are checked and stored, and any faulty electrical equipment is identified, tagged and isolated according to workplace procedures 
Workplace documentation is processed according to workplace procedures 
Job requirements are determined from workplace instructions 
Reasons for the modification are identified and confirmed with appropriate persons 
Modification options are identified and reported to appropriate persons according to workplace procedures 
Hazards associated with the work are identified and risks are managed 
Legal and safety impacts of the modification are considered, as required, according to regulatory requirements 
Manufacturer specifications for the existing network electronic control systems are sourced and interpreted 
Criteria for selecting the modification method and evaluating the outcomes are identified and documented 
Proposed modification method is identified, selected and evaluated from available options 
Selected option, including material choices and processes, is developed in detail and progressively assessed against established criteria 
Modification specification is documented according to workplace procedures 
Tools, test equipment and materials required to support the modification procedure are identified, selected and prepared for use 
Selected modification method is carried out according to workplace procedures and safety requirements 
Post-modification testing is carried out according to workplace procedures to confirm modification outcomes are as intended, and any problems detected as having been introduced during the modification process are rectified 
Test results and other diagnostic findings are verified, as required, by using reliable alternative or optional processes 
Variations needed during the modification process or as a result of testing are incorporated into the modification specification 
Information and detail relating to the modification are documented and provided to the appropriate parties according to regulatory and commercial obligations 
Final inspection is made to ensure work is to workplace expectations 
Work area is cleaned, waste and non-recyclable materials are disposed of, and recyclable material is collected 
Tools and equipment are checked and stored, and any faulty electrical equipment is identified, tagged and isolated according to workplace procedures 
Workplace documentation is processed according to workplace procedures 

Forms

Assessment Cover Sheet

AURETR033 - Develop and apply network electronic control system modifications
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:


Assessment Record Sheet

AURETR033 - Develop and apply network electronic control system modifications

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: