Unit of Competency Mapping – Information for Teachers/Assessors – Information for Learners

MSFGG3015 Mapping and Delivery Guide
Fabricate and install shower screens and wardrobe doors

Version 1.0
Issue Date: May 2024


Qualification -
Unit of Competency MSFGG3015 - Fabricate and install shower screens and wardrobe doors
Description
Employability Skills
Learning Outcomes and Application This unit of competency covers planning, fabricating and installing shower screens and wardrobe doors fitted with safety vinyl backed mirror or textured vinyl coated board in residential and commercial locations.Licensing, legislative or certification requirements may apply to this unit and relevant state/territory and local government agencies should be consulted to determine any necessary certification or licensing for undertaking glass and glazing work. Access to construction sites requires certification of general induction training specified by the National Code of Practice for Induction for Construction Work (ASCC 2007).
Duration and Setting X weeks, nominally xx hours, delivered in a classroom/online/blended learning setting.

Assessors must:

hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors

have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification

be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.

Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.

Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.

Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.

Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.

Access is required to shower screen/wardrobe door glass and mirror, aluminium framing material, fixtures, waterproof sealant, workplace operating procedures, personal protective equipment and a fabrication and installation location.
Prerequisites/co-requisites
Competency Field
Development and validation strategy and guide for assessors and learners Student Learning Resources Handouts
Activities 		Slides
PPT 		Assessment 1 Assessment 2 Assessment 3 Assessment 4
Elements of Competency Performance Criteria              
Element: Identify work requirements
  • Work requirements for the type of shower screen/wardrobe door to be fabricated and installed are identified from work instructions, including the identification of its pattern or plan
  • Work health and safety (WHS) requirements for fabrication and installation of shower screens and wardrobe doors, including personal protective equipment, are observed throughout the work
  • The process for fabricating and installing shower screens and wardrobe doors is identified
  • Glass fixing method and joining devices or materials are identified in accordance with specifications or type of materials to be used and Australian Standards
  • Quantities of materials required are calculated from plans/work instructions or by measuring the fixture opening
  • Tools and equipment appropriate to the fixing method are identified
       
Element: Prepare for work
  • Work sequence is determined in a logical order to suit the job and workplace procedures
  • Tools, equipment and materials are selected and checked prior to use to ensure they are appropriate for the work, serviceable and in a safe condition
  • Components of the shower screen/wardrobe door are checked against specifications or job order for size, quantity, finish and profile
       
Element: Fabricate and install shower screen/wardrobe door
  • If required, aluminium frame is fabricated in accordance with workplace procedures or industry practice
  • Fittings are attached to screen in accordance with workplace procedures or industry practice
  • Shower screen/wardrobe door is installed in shower opening/wardrobe in accordance with workplace procedures or industry practice
  • Shower screen is waterproof sealed in accordance with workplace procedures or industry practice
       
Element: Complete work
  • Shower screen/wardrobe door is inspected for quality of work and repaired, re-fabricated or reinstalled, as required, in accordance with workplace procedures
  • Material which can be reused is collected and stored and waste and scrap material are removed for disposal or recycling, as required
  • Work area is cleaned and rubbish disposed of, as appropriate
  • Tools, equipment and unused materials are cleaned and removed and stored appropriately
  • Workplace documentation is completed in accordance with workplace requirements including calculating the cost of glass, fittings, materials and labour
       


Evidence Required

List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.

Elements describe the essential outcomes.

Performance criteria describe the performance needed to demonstrate achievement of the element.

1

Identify work requirements

1.1

Work requirements for the type of shower screen/wardrobe door to be fabricated and installed are identified from work instructions, including the identification of its pattern or plan

1.2

Work health and safety (WHS) requirements for fabrication and installation of shower screens and wardrobe doors, including personal protective equipment, are observed throughout the work

1.3

The process for fabricating and installing shower screens and wardrobe doors is identified

1.4

Glass fixing method and joining devices or materials are identified in accordance with specifications or type of materials to be used and Australian Standards

1.5

Quantities of materials required are calculated from plans/work instructions or by measuring the fixture opening

1.6

Tools and equipment appropriate to the fixing method are identified

2

Prepare for work

2.1

Work sequence is determined in a logical order to suit the job and workplace procedures

2.2

Tools, equipment and materials are selected and checked prior to use to ensure they are appropriate for the work, serviceable and in a safe condition

2.3

Components of the shower screen/wardrobe door are checked against specifications or job order for size, quantity, finish and profile

3

Fabricate and install shower screen/wardrobe door

3.1

If required, aluminium frame is fabricated in accordance with workplace procedures or industry practice

3.2

Fittings are attached to screen in accordance with workplace procedures or industry practice

3.3

Shower screen/wardrobe door is installed in shower opening/wardrobe in accordance with workplace procedures or industry practice

3.4

Shower screen is waterproof sealed in accordance with workplace procedures or industry practice

4

Complete work

4.1

Shower screen/wardrobe door is inspected for quality of work and repaired, re-fabricated or reinstalled, as required, in accordance with workplace procedures

4.2

Material which can be reused is collected and stored and waste and scrap material are removed for disposal or recycling, as required

4.3

Work area is cleaned and rubbish disposed of, as appropriate

4.4

Tools, equipment and unused materials are cleaned and removed and stored appropriately

4.5

Workplace documentation is completed in accordance with workplace requirements including calculating the cost of glass, fittings, materials and labour

Interpret work order and locate and apply relevant information

Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment

Identify materials used in the work process

Follow work instructions, operating procedures and inspection processes to:

minimise the risk of injury to self or others

prevent damage to goods, equipment and products

maintain required production output and product quality

Measure for fabrication and installation of two (2) of the following in accordance with AS 3740:2010 Waterproofing of domestic wet areas:

sliding shower door

pivot shower door

semi-frameless and frameless shower screens

Measure for installation of wardrobe doors:

working from product specification data sheets identifying and selecting product materials

selecting glass in accordance with AS 1288:2006 Glass in buildings - Selections and installation

fabricating frame and sash components, including cutting, tooling and drilling

identifying, selecting and installing component hardware, including weather seals, wheels, hinges, guides and handles

assembling frames, including glass and gaskets

Install shower screens and wardrobe doors

Calculate the cost of shower screens and wardrobe doors

Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements

Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures

Avoid backtracking, work flow interruptions or wastage

Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity

Work flow requirements in relation to the fabrication and installation of shower screens and wardrobe doors

Characteristics of materials used and uses of products produced

Workplace safety system requirements related to the fabrication and installation of shower screens and wardrobe doors

Correct identification of equipment, processes and procedures

Relevant Australian Standards

Submission Requirements

List each assessment task's title, type (eg project, observation/demonstration, essay, assignment, checklist) and due date here

Assessment task 1: [title]      Due date:

(add new lines for each of the assessment tasks)

Assessment Tasks

Copy and paste from the following data to produce each assessment task. Write these in plain English and spell out how, when and where the task is to be carried out, under what conditions, and what resources are needed. Include guidelines about how well the candidate has to perform a task for it to be judged satisfactory.

Elements describe the essential outcomes.

Performance criteria describe the performance needed to demonstrate achievement of the element.

1

Identify work requirements

1.1

Work requirements for the type of shower screen/wardrobe door to be fabricated and installed are identified from work instructions, including the identification of its pattern or plan

1.2

Work health and safety (WHS) requirements for fabrication and installation of shower screens and wardrobe doors, including personal protective equipment, are observed throughout the work

1.3

The process for fabricating and installing shower screens and wardrobe doors is identified

1.4

Glass fixing method and joining devices or materials are identified in accordance with specifications or type of materials to be used and Australian Standards

1.5

Quantities of materials required are calculated from plans/work instructions or by measuring the fixture opening

1.6

Tools and equipment appropriate to the fixing method are identified

2

Prepare for work

2.1

Work sequence is determined in a logical order to suit the job and workplace procedures

2.2

Tools, equipment and materials are selected and checked prior to use to ensure they are appropriate for the work, serviceable and in a safe condition

2.3

Components of the shower screen/wardrobe door are checked against specifications or job order for size, quantity, finish and profile

3

Fabricate and install shower screen/wardrobe door

3.1

If required, aluminium frame is fabricated in accordance with workplace procedures or industry practice

3.2

Fittings are attached to screen in accordance with workplace procedures or industry practice

3.3

Shower screen/wardrobe door is installed in shower opening/wardrobe in accordance with workplace procedures or industry practice

3.4

Shower screen is waterproof sealed in accordance with workplace procedures or industry practice

4

Complete work

4.1

Shower screen/wardrobe door is inspected for quality of work and repaired, re-fabricated or reinstalled, as required, in accordance with workplace procedures

4.2

Material which can be reused is collected and stored and waste and scrap material are removed for disposal or recycling, as required

4.3

Work area is cleaned and rubbish disposed of, as appropriate

4.4

Tools, equipment and unused materials are cleaned and removed and stored appropriately

4.5

Workplace documentation is completed in accordance with workplace requirements including calculating the cost of glass, fittings, materials and labour

Specifies different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Range is restricted to essential operating conditions and any other variables essential to the work environment.

Unit context includes:

WHS requirements, including legislation, building codes, material safety management systems, hazardous and dangerous goods codes, and local safe operating procedures or equivalent

work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements

work requires individuals to demonstrate some discretion, judgement and problem solving

Shower screens are glass panels and include:

framed

semi-frameless and frameless screens

sliding screens

pivot screens and returns

Materials include:

aluminium shower screen and wardrobe extrusions

laminated

toughened and organic coated glass

vinyl backed mirror

textured vinyl board

glazing and bump rubbers

shower screen

wardrobe hardware

sealants

Tools and equipment include:

power saws

pneumatic equipment

hydraulic and manual presses

tooling

drills

screwdrivers and rubber mallets and general glazing tools

spirit and laser levels

Fittings include:

wheels

hinges

handles

pivot blocks

corner blocks

fasteners

Personal protective equipment includes:

that prescribed under legislation, regulation and enterprise policies and practices:

gauntlets

gloves

safety glasses

hard hats

safety footwear

aprons and overalls

Information and procedures include:

workplace procedures relating to the use of tools and equipment and personal protective equipment

work instructions, including job sheets, cutting lists, plans, drawings and designs

workplace procedures relating to reporting and communication

manufacturer specifications and operational procedures

AS 1288:2006 Glass in buildings - Selection and installation

AS 3740:2010 Waterproofing of domestic wet areas

Copy and paste from the following performance criteria to create an observation checklist for each task. When you have finished writing your assessment tool every one of these must have been addressed, preferably several times in a variety of contexts. To ensure this occurs download the assessment matrix for the unit; enter each assessment task as a column header and place check marks against each performance criteria that task addresses.

Observation Checklist

Tasks to be observed according to workplace/college/TAFE policy and procedures, relevant legislation and Codes of Practice Yes No Comments/feedback
Work requirements for the type of shower screen/wardrobe door to be fabricated and installed are identified from work instructions, including the identification of its pattern or plan 
Work health and safety (WHS) requirements for fabrication and installation of shower screens and wardrobe doors, including personal protective equipment, are observed throughout the work 
The process for fabricating and installing shower screens and wardrobe doors is identified 
Glass fixing method and joining devices or materials are identified in accordance with specifications or type of materials to be used and Australian Standards 
Quantities of materials required are calculated from plans/work instructions or by measuring the fixture opening 
Tools and equipment appropriate to the fixing method are identified 
Work sequence is determined in a logical order to suit the job and workplace procedures 
Tools, equipment and materials are selected and checked prior to use to ensure they are appropriate for the work, serviceable and in a safe condition 
Components of the shower screen/wardrobe door are checked against specifications or job order for size, quantity, finish and profile 
If required, aluminium frame is fabricated in accordance with workplace procedures or industry practice 
Fittings are attached to screen in accordance with workplace procedures or industry practice 
Shower screen/wardrobe door is installed in shower opening/wardrobe in accordance with workplace procedures or industry practice 
Shower screen is waterproof sealed in accordance with workplace procedures or industry practice 
Shower screen/wardrobe door is inspected for quality of work and repaired, re-fabricated or reinstalled, as required, in accordance with workplace procedures 
Material which can be reused is collected and stored and waste and scrap material are removed for disposal or recycling, as required 
Work area is cleaned and rubbish disposed of, as appropriate 
Tools, equipment and unused materials are cleaned and removed and stored appropriately 
Workplace documentation is completed in accordance with workplace requirements including calculating the cost of glass, fittings, materials and labour 

Forms

Assessment Cover Sheet

MSFGG3015 - Fabricate and install shower screens and wardrobe doors
Assessment task 1: [title]

Student name:

Student ID:

I declare that the assessment tasks submitted for this unit are my own work.

Student signature:

Result: Competent Not yet competent

Feedback to student

 

 

 

 

 

 

 

 

Assessor name:

Signature:

Date:

Assessment Record Sheet

MSFGG3015 - Fabricate and install shower screens and wardrobe doors

Student name:

Student ID:

Assessment task 1: [title] Result: Competent Not yet competent

(add lines for each task)

Feedback to student:

 

 

 

 

 

 

 

 

Overall assessment result: Competent Not yet competent

Assessor name:

Signature:

Date:

Student signature:

Date: