List the assessment methods to be used and the context and resources required for assessment. Copy and paste the relevant sections from the evidence guide below and then re-write these in plain English.
1. Plan and prepare for air drilling | 1.1 Access, interpret and apply conduct air drilling documentation, and ensure the work activity is compliant 1.2 Obtain, read, interpret, clarify and confirm work requirements 1.3 Identify and address potential risks, hazards and environmental issues and implement control measures 1.4 Select and wear personal protective equipment appropriate for work activities 1.5 Communicate and coordinate activities with others throughout the work activity 1.6 Obtain and interpret emergency procedures, and be prepared for fire/accident/emergency |
2. Inspect and maintain air drilling equipment | 2.1 Carry out pre-start and start up procedures 2.2 Ensure restraining devices are not damaged or worn and are correctly fitted 2.3 Fit or replace restraining devices 2.4 Inspect and maintain the cyclone in safe and serviceable condition 2.5 Ensure mounting and security of cyclone is adequate for safe operation, particularly when down hole water may result in release of energy 2.6 Maintain dust suppression systems to ensure minimal emission of airborne dust and integrity of sample quality 2.7 Inspect pressure relief valves to ensure they have not been tampered with |
3. Drill using air drilling methods | 3.1 Identify, select and apply rig operational controls 3.2 Select and use appropriate drill rod and drill string components given hole specification and anticipated ground conditions 3.3 Operate make-up and break-out equipment 3.4 Select and use appropriate type and size of in-hole tools given hole specification and anticipated ground conditions 3.5 Drill/open-up hole collar as required to suit given ground conditions and hole specification 3.6 Install drill hole collar casing and seal at the hole collar 3.7 Install outside hole return collar device, if required, given hole specification of open or reverse circulation drill hole 3.8 Operate drill rod and pipe handling equipment 3.9 Add and remove drill rods or casing and other in-hole equipment 3.10 Monitor and adjust air pressure and other drilling parameters to achieve maximum performance 3.11 Monitor and control down hole water conditions to ensure integrity of the hole, drill cuttings and sample quality 3.12 Monitor and control discharge from outside hole return collar device 3.13 Calculate depth of hole |
4. Select and use drilling additives | 4.1 Identify ground conditions requiring the use of drilling additives 4.2 Select appropriate drilling additives to suit ground conditions 4.3 Preparing required drilling additives 4.4 Use drilling additives to achieve required results |
5. Take samples | 5.1 Select and check sample devices to ensure client sample quantity and quality specifications are met 5.2 Clean or supervise the cleaning of sample devices 5.3 Monitor splitting, bagging, presentation, and marking of samples to ensure client specifications are met 5.4 Identify and promptly rectify sample blockages affecting or having the potential to affect sample quality 5.5 Clear sample delivery hose blockages safely 5.6 Clear outside return hole blockages of collared holes as required 5.7 Supervise drill crew and ensure all sampling tasks are carried out correctly and safely |
6. Respond to problems | 6.1 Monitor drill cuttings or sample quality, quantity and air return 6.2 Identify possible problems in equipment or process 6.3 Determine possible cause(s) of problems 6.4 Rectify problem(s) using appropriate solution within area of responsibility 6.5 Follow through items initiated until final resolution has occurred 6.6 Report problems outside area of responsibility to designated person |
7. Complete equipment maintenance and housekeeping | 7.1 Supervise the use of specified personal protective equipment when using grinders or bit sharpening equipment 7.2 Supervise the selection and correct fitting grinding disks, wheels and stones 7.3 Monitor wear of in-hole tools 7.4 Check, maintain, and/or replace compressed air hoses and hose fittings or clamps 7.5 Supervise the correct sharpening and maintenance of in-hole tools 7.6 Inspect, dismantle, replace worn or damaged components and reassemble in-hole equipment 7.7 Carry out shutdown and secure equipment 7.8 Ensure housekeeping activities are completed 7.9 Process records |
Evidence is required to be collected that demonstrates a candidate’s competency in this unit. Evidence must be relevant to the roles within this sector’s work operations and satisfy all of the requirements of the performance criteria of this unit and include evidence that the candidate:
locates and applies relevant documentation, policies and procedures
implements the requirements, procedures and techniques for the safe, effective and efficient completion of air drilling including:
applying prescribed thread form torque parameters during make-up of down hole equipment and consumables
applying correct internal and external calipers, vernier, rule and or tape measure for identification of drill pipe/rod diameter wear limits, measurement of bits/shrouds and other down hole equipment
applying correct measurement of drill string length
applying methods for calculating hole depth
works effectively with others to undertake and complete air drilling tasks that meets all of the required outcomes including:
complying with written and verbal reporting requirements and procedures
communicating clearly and concisely with others to receive and clarify work instructions
communicating clearly and concisely with others to resolve coordination requirements prior to commencing and during work activities
demonstrates completion of the conduction of air drilling that safely, effectively and efficiently meets all of the required outcomes on more than one (1) occasion including:
fitting/replacingg must demonstrate knowledge restraining devices
ensure mounting and security of cyclone is adequate for safe operation, particularly when down hole water may result in release of energy
maintaining dust suppression systems to ensure minimal emission of airborne dust and integrity of sample quality
selecting and using appropriate drill rod and drill string components given hole specification and anticipated ground conditions
drilling/open-up hole collar as required to suit given ground conditions and hole specification
installing drill hole collar casing and seal at the hole collar
monitoring and adjusting air pressure and other drilling parameters to achieve maximum performance
monitoring and controlling down hole water conditions to ensure integrity of the hole, drill cuttings and sample quality
monitoring and controlling discharge from outside hole return collar device
calculating depth of hole
selecting appropriate drilling additives to suit ground conditions
preparation of required drilling additives
selecting and checking sample devices to ensure client sample quantity and quality specifications are met
monitoring splitting, bagging, presentation, and marking of samples to ensure client specifications are met
supervising drill crew and ensuring all sampling tasks are carried out correctly and safely
The candidate must demonstrate knowledge in conducting air drilling through:
accessing, interpreting and applying the organisation and site requirements and procedures for:
work, health and safety
environmental issues
operating drill rig
housekeeping
understanding the importance to match like threads with like threads on all threaded components and make up torque requirements applicable to thread form in use
understanding the relationship between pressure, volume, hole diameter, pipe diameter and calculation of up hole velocity
understanding the drill pipe, rod and thread form wear limit parameters
understanding the need for correct hole collaring, use of casing and collar sealing techniques
complying with the TC bit sharpening procedures
identifying the potential problems related to inaccurate measurement and usage sequence of ground engaging consumables and related down hole components
identifying the hazard control measures to enable safe use of compressed air
identifying the importance of sample quantity
understanding the role that drill cuttings blockages play in affecting sample quality
identifying the safe procedures to clear down and up hole drill cuttings blockages within the outside hole return, down hole equipment and up hole sample system and/or hose
identifying the critical need for correct fitting inspection and maintenance replacement of restraining devices
identifying the hazards associated with the collection of high velocity drilling cuttings
identifying the reasons for checking inner tubes and inner tube sealing devices in RC drill pipe
identifying the hazards associated with wire-line operations and applicable control measures
identifying the various thread forms used in air drilling
identifying the various in-hole tools and correct application given ground conditions
identifying the need for managing uncontaminated samples
being prepared for fire/accident/emergency