AHCARB207A
Perform ground based rigging

This unit of competency covers the process of rigging on the ground and defines the standard required to: select and examine ropes and equipment; select and use a rigging system as directed; assist with tree operations; use established methods of rigging and communicate effectively with work crew.

Application

This unit applies to work crew engaged in the process of ground based rigging and applies to the appropriate selection and use of rigging equipment and methods. Ground based rigging work requires the application of arboricultural knowledge and skills including different techniques of rigging to raise, lower, control or redirect a load in undertaking tree pruning and /or tree removal. Some discretion and judgement is required. Ground based rigging is likely to be performed under routine supervision with periodic checking by supervisors or qualified arborists and is usually done within established routines, using documented low risk work methods and procedures and according to stringent Occupational Health and Safety (OHS) guidelines. Interactive communications within the work crew are integral to the rigging process. Equipment is used and maintained in accordance with the manufacturer's specifications. Work practices are in accordance with relevant legislation and contract requirements. This unit does not cover crane operations.


Elements and Performance Criteria

ELEMENT

PERFORMANCE CRITERIA

1. Assist in the preparation of the work site

1.1. Assistance is provided to confirm the location of worksite and location of the correct tree as per the scope of works.

1.2. Required site permits and licences are obtained.

1.3. Assistance is provided to a qualified arborist in the inspection of the tree for structural defects.

1.4. Site hazards are identified; risks assessed and reported to the supervisor or qualified arborist.

1.5. The work zone is confirmed with the work crew and is monitored.

1.6. Traffic management plans for the work site are implemented as instructed.

2. Prepare for rigging

2.1. Rigging method is discussed by the work crew and determined by supervisor or qualified arborist.

2.2. Rigging method confirms the risk controls selected in accordance with established and documented low risk work methods.

2.3. Appropriate rigging equipment is selected as directed.

2.4. Rigging equipment is examined, assembled, installed and checked for equipment defects.

3. Perform rigging operations

3.1. Communication with the person cutting is commenced, instructions are received and appropriate responses are provided.

3.2. Appropriate knots are selected and tied as required.

3.3. Rigging system and environmental conditions are monitored.

3.4. Rigging is adjusted as instructed.

3.5. Load is controlled and raised, lowered or re-directed as instructed.

3.6. Load is disconnected from the rigging system and rigging equipment is checked.

3.7. The appropriate component of the rigging system is returned to the person cutting.

4. Complete rigging operations

4.1. The load is removed from the drop zone.

4.2. Rigging operations are completed as per scope of works.

4.3. Tools, equipment and machinery are cleaned, checked, and replaced if faulty or worn, and stored.

Required Skills

Required skills

technical skills sufficient to:

identify, use and maintain rigging equipment and devices on the ground

examine equipment before and during use and identify problems, defects and faults

select rigging equipment as directed

assemble a range of rigging equipment

safely operate and maintain rigging equipment

carry out rigging operations appropriate to site conditions

identify unsafe rigging practices

understand equipment terminology and names

select and tie essential knots required for rigging

operate lowering devices as required

practice rescue techniques

store and maintain rigging equipment

install a rope in a tree.

communication skills sufficient to:

use and respond to appropriate communication and interpersonal techniques and methods with colleagues and others; and,

use voice, hand and whistle signals with other operators to maintain effective and low risk rigging operations

report information about problems, defects and faults.

literacy skills sufficient to:

accurately locate and report information;

interpret written text material; and,

interpret, apply and convey information in written, diagrammatic and/or verbal form.

spatial skills sufficient to:

estimate distances and dimensions of trees and equipment

estimate the centre of gravity for balancing a load

estimate areas for safe work zones.

numeracy skills to:

understand and recognise numerical terms of equipment breaking strains, safe working loads, manufacturer's specifications and labeling

use basic geometry to measure distances and dimensions

problem solving skills sufficient to:

identify work requirements;

identifying any faults in tools, equipment or materials

recognise own limitations in identifying problems in conditions and trees for rigging

demonstrate appropriate response procedures following identification of problems; and, provide alternative rigging solutions

apply low risk work practices including the use of personal and protective equipment and control of hazards

identify hazards, assess risk and report to supervisor.

teamwork skills sufficient to:

use communications to complete complex tasks efficiently and safely

coordinate own work with others to action tasks;

to relate to people from a range of cultural and ethnic backgrounds and with varying physical and mental abilities

the ability to comply with legislation, regulations, standards, codes of practice and established safe practices and procedures for rigging.

Required knowledge

organisational and site standards, requirements, policies and procedures for rigging

types and purposes of a range of rigging equipment and devices

the use, operation and maintenance of rigging equipment in accordance with the manufacturer's specifications and recommendations

common problems with rigging and their potential consequences and solutions

established communication and management channels and protocols

the recognition of structural defects in trees

methods of using and operational principles and limitations of friction devices

procedures for recording and reporting workplace information

appropriate mathematical procedures for estimating and measuring

common rigging hazards

basic physics for load distribution, gravity, heat, potential and kinetic energy, mass, force and leverage

basic knowledge and understanding of applicable standards and Code of Practice relevant to the full range of processes for rigging

environmental protection requirements

basic anatomy, physiology and nomenclature of trees

safe working load of rigging equipment

awareness of breaking strength, safety factor and cycles to failure

signals and communication systems

first aid and rescue procedures

use of personal protection equipment.

Evidence Required

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

Critical aspects for assessment and evidence required to demonstrate competency in this unit

The evidence required to demonstrate competency in this unit must be relevant to workplace operations and satisfy holistically all of the requirements of the performance criteria and required skills and knowledge and include achievement of the following:

select and examine ropes and equipment;

select and use a rigging system as directed;

assist with tree operations;

use established methods of rigging

communicate effectively with work crew.

Context of and specific resources for assessment

Competency requires the application of work practices under work conditions. Selection and use of resources for some work sites may differ due to the regional or enterprise circumstances. There is an industry expectation for refresher training and assessment.


Range Statement

The range statement relates to the unit of competency as a whole.

Tree may include:

the range of tree species that are:

hardwood

softwood

palms and palm-like

trees that are:

alive

dead

single or multi-stemmed

leaning or straight.

Structural defects may include:

cracks

splits

cavities

decay and inclusions.

Site hazards may include:

aspects of terrain such as:

ground slope

uneven/unstable surfaces

high risk trees and tree parts

tree species characteristics

lean of tree

canopy attributes

overhead and underground services

adjacent objects such as infrastructure

existing vegetation such as ground vegetation density

excavations

traffic

hazardous materials

fires

insects and animals

other personnel and machinery.

Work zone may include:

the exclusion zone

safe drop zone

safe fall zone

traffic management zone

asset management zone area under the load

the area that the load is directed to.

Traffic may include:

pedestrian

vehicle.

Rigging method may include:

simple rope

taut line

speed line

tag-pull line

lowering

raising

cradling

tip or butt lowering

false crotch.

Rigging equipment may include:

ropes, including aspects of rope such as:

materials

construction

diameter

limits

terminations

karabiners

pulleys

slings

shackles

rapids.

Slings may be:

spliced, sewn or swaged; and may be adjustable, continuous or fixed length.

Slinging configurations could include choke or basket.

Equipment defects may include:

signs of wear, melting, burning, stretching, cracking, incompatibility, overload failure, or equipment that is cut, bent, broken or faulty.

Communication may include:

voice communications

whistles

hand signals.

Knots may include:

bowline

running bowline

bowline on a bight

blood knot

tautline

sheet bend

Prussik

figure 8

friction

alpine

timber hitch

clove hitch

half hitch.

Rigging system includes:

the assembly of all the component parts of rigging equipment. This may include mechanical advantage and friction from tree or friction devices or other fixed objects.

Environmental conditions may include:

the range of variations in weather such as wind speed and direction.

Load may include:

tree

tree parts

rigging equipment

tools.

Disconnected may include:

the method of removing the rigging such as un-clipped, untied, unscrewed, unshackled or un-hitched.


Sectors

Unit sector

Arboriculture


Employability Skills

This unit contains employability skills.


Licensing Information

Not Applicable