AURM441868B
Select and prepare tyres and wheels for motorsport applications

This unit of competency describes the skills and knowledge required to select and prepare tyres and wheels for motorsport applications to optimise handling performance.It requires the technical ability to select and prepare tyres and wheels for use on a competition vehicle, fit tyre and wheel assemblies, prepare pre-race tyre and wheels, document post-race tyre and wheel data and adjust, as required.No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.

Application

This unit applies to individuals who select and prepare tyres and wheels used in motorsports to optimise handling performance. This includes mounting wheels, conducting pre-race preparation, and post-race maintenance stock control and storage procedures.


Elements and Performance Criteria

ELEMENT

PERFORMANCE CRITERIA

1. Determine and select competition vehicle tyres and wheels

1.1. Use controlling body and category rules, supplementary regulations, component supplier specifications and team instructions to specify task requirements, including design, quality, material, equipment and quantities

1.2. Observe occupational health and safety (OHS) requirements, including regulatory requirements, equipment and system isolation requirements, and personal protection needs, throughout the work

1.3. Use regulations and specifications/tolerances to identify a competitive advantage

1.4. Check specifications for required operating conditions and seek clarification of specifications, where required

1.5. Formulate tyre and wheel requirements according to known factors

1.6. Select tyre and wheel assemblies for application against requirements and document and report to appropriate persons

2. Prepare work area and equipment

2.1. Check tooling and equipment for safe and effective operation

2.2. Clean and lay out work are for job requirements

2.3. Report problems with the work area or the operation of equipment to appropriate persons

3. Mount tyre and wheel assembly to vehicle

3.1. Clean or treat mounting surfaces and threaded components and check for damage

3.2. Select tyre and wheel assemblies from stock according to markings (i.e. scrutineers/category officials or team markings) and check against criteria for an event

3.3. Inspect tyre and wheel assemblies for serviceability

3.4. Fit tyre and wheel assemblies using mounting sequence and techniques

3.5. Tension fasteners to team/component supplier specifications and engage fastener locking device, where fitted

3.6. Check during and after installation to ensure accurate and complete fitting

3.7. Report problems with tyre and wheel assemblies to appropriate persons

4. Conduct pre-race tyre and wheel preparation

4.1. Obtain recommended start/cold pressures and optimum operating/hot pressures

4.2. Set tyre inflation pressures to specifications

4.3. Measure and document baseline tyre temperature, ambient and traction surface temperatures

4.4. Buff tyres, if specified

4.5. Fit and turn on tyre warmers, if specified (and if allowed in category rules)

5. Conduct post-race tyre and wheel maintenance

5.1. Check tyre pressures and temperatures at specified times and document data

5.2. Read tyre contact surface for handling and wear indications and document data

5.3. Question driver/rider for assessment of handling characteristics and document data

5.4. Source additional data, as required, and identify changes (if any) required to tyres and wheels prior to next race

5.5. Clean tyre contact surfaces, as required

5.6. Change tyres to different compound or pattern, as required

5.7. Change tyre pressures, as required

5.8. Tag or mark removed tyres for data audit trail

6. Clean up and complete documentation

6.1. Pack and store tyres

6.2. Assess tyre and wheel stock inventory and document and report to appropriate persons

6.3. Maintain tooling and return to storage

6.4. Complete team/component supplier documentation

Required Skills

Required skills

Required skills include:

technical skills to the level required to use workplace technology related to selecting and preparing tyres and wheels for motorsport applications, including tooling, equipment, calculators and measuring devices

communication skills to the level required to communicate ideas and information to enable clarification of requirements, coordination of work with supervisors and other workers, and to report work outcomes and problems

literacy skills to the level required to collect, organise and understand information related to selecting and preparing tyres and wheels for motorsport applications, team requirements, manufacturer/component supplier specifications and safety procedures

numeracy skills to the level required to use mathematical ideas and techniques to correctly complete measurements and calculations required during the selection and preparation of tyres and wheels for motorsport applications

problem-solving skills to the level required to use pre-checking and inspection techniques to anticipate assembly problems in order to work efficiently and effectively

team skills to the level required to work with others to foster the team by recognising dependencies and using cooperative approaches to optimise workflow and productivity

planning skills to the level required to plan and organise activities, including the preparation and layout of the worksite, and the coordination of equipment, systems and materials to avoid backtracking, workflow interruptions or wastage

Required knowledge

Required knowledge includes:

controlling body rules, category rules and supplementary regulations, manufacturer/component supplier specifications (e.g. wheel size, application and pressures both cold and hot) and team requirements/job specifications

wheel and tyre types, manufacturer/component supplier markings, function, application and limitations, including specifications, handling characteristics and manufacturer/component supplier recommendation for use

tyre and wheel serviceability inspection techniques

reading tyres for handling and wear indications

driver/rider debriefing

tyre temperature testing

tyre measurement, including stagger calculations

tyre buffing, cleaning and warming

tyre and wheel storage methods

markings by scrutineers/category officials or team markings

record keeping techniques

procedures for reporting equipment faults and component defects

OHS policies and procedures

applicable commonwealth, state or territory legislation, regulations, standards and codes of practice, including OHS, personal safety and environment, relevant to selecting and preparing tyres

Evidence Required

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

Critical aspects for assessment and evidence required to demonstrate competency in this unit

Assessors must be satisfied that the candidate can competently and consistently:

interpret and apply team requirements, controlling body and category rules and supplementary regulations

correctly apply and use safety equipment and personal protective equipment

follow task instructions, operating procedures and inspection processes to:

minimise the risk of injury to self or others

prevent damage to competition vehicle or equipment

achieve required outcomes within team time and quality standards

correctly prepare and fit tyres and wheels to a minimum of two (2) different vehicles in differing situations

comply with tyre and wheel manufacturer/component supplier recommendations for use

work effectively with others

modify activities to cater for variations in workplace context and environment.

Context of, and specific resources for assessment

The application of competency is to be assessed in the workplace or a simulated environment that reflects as far as possible the actual working environment.

Assessment is to occur using standard and authorised work practices, safety requirements and environmental constraints.

Assessment is to comply with relevant regulatory requirements, including specified Australian standards.

Where applicable, reasonable adjustment must be made to work environments and training situations to accommodate ethnicity, age, gender, demographics and disability.

The following resources should be made available:

access to competition vehicles

associated assembly tooling

related computing, operational and inventory support systems

work areas

material and equipment

information on work specifications

customer requirements

organisational procedures

safety procedures and regulations

quality standards.

Method of assessment

Assessment must satisfy the endorsed Assessment Guidelines of this Training Package.

Assessment methods must confirm consistency and accuracy of performance (over time and in a range of workplace relevant contexts) together with application of Required Skills and Knowledge.

Assessment methods must be by direct observation of tasks and include questioning on Required Skills and Knowledge to ensure its correct interpretation and application.

Assessment may be applied under project-related conditions (real or simulated) and require evidence of process.

Assessment must confirm a reasonable inference that competency is able not only to be satisfied under the particular circumstance, but is able to be transferred to other circumstances.

Competence in this unit may be assessed in conjunction with other functional units which together form part of the holistic work role.

Guidance information for assessment

Assessment processes and techniques must be culturally sensitive and appropriate to the language and literacy capacity of the candidate and the work being performed.


Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Inspection for serviceability

Inspection for serviceability may include:

checking wheel condition for damage or fatigue

valve body/pressure relief valves

ensuring inner surface of wheel is free from contaminants (e.g. oil/grease, water and dirt/gravel)

checking tyre condition for signs of damage, excessive wear and flat spots

Competitive advantage

Competitive advantage may include:

technical advantage

psychological advantage

promotional advantage

OHS requirements

OHS requirements are to be in accordance with applicable commonwealth, state or territory legislation and regulations, and organisational safety policies and procedures, and may include:

personal protective equipment and clothing, including closed-in shoes, long trousers, handling gloves and other equipment

safety equipment

first aid equipment

hazard and risk control

elimination of hazardous materials and substances

manual handling, including shifting, lifting and carrying

emergency procedures

team insurance requirements

material safety management systems

controlling body requirements

manufacturer/component supplier specifications

local safe operating procedures

Legislative requirements

Legislative requirements are to be in accordance with applicable commonwealth, state or territory legislation, regulations, certification requirements and codes of practice, and may include:

award and enterprise agreements

industrial relations

Australian standards

Australian Design Rules

confidentiality and privacy

OHS

the environment

equal opportunity

anti-discrimination

duty of care

health regulations

Tooling and equipment

Tooling and equipment may include:

pit lane/service area specified tooling

lifting devices

air tooling

torque wrenches

tyre hardness test instruments

air pressure gauges

tyre buffers and cleaners

tyre heaters

pyrometers

hand tooling

Information and procedures

Information and procedures may include:

controlling body rules, category rules and supplementary regulations

event scheduling and location details

team procedures and standards related to:

selecting and preparing tyres and wheels for motorsport applications

reporting and communication

use of tooling and equipment

emergency service contacts and team persons emergency contacts

team emergency and event procedures for accidents or injury

work instructions, including worksheets, material safety data sheets (MSDS), assembly procedures, plans, drawings, designs and checklists

manufacturer/component supplier specifications and application procedures for test equipment and material

Australian Design Rules (where applicable)

safety body publications

environmental, hazardous chemicals and dangerous goods legislation and local requirements relating to the disposal and use of fuels, lubricants, coolants and cleaning agents


Sectors

Unit sector

Motorsport


Employability Skills

This unit contains employability skills.


Licensing Information

Refer to Unit Descriptor