CPCCWC2001A
Complete penetrations and flashings

This unit of competency specifies the outcomes required to complete the penetrations and flashings associated with wall and ceiling lining. It does not cover the technical aspects of passive fire systems.It includes planning and preparation for work, selection and safe use of tools and equipment to complete the penetrations and flashings, restoration of the integrity of the wall or ceiling, and completion of post work clean-up activities.

Application

This unit supports the attainment of skills and knowledge to safely and efficiently complete penetrations and flashings while working with others as a member of a team.


Prerequisites

CPCCOHS2001A

Apply OHS requirements, policies and procedures in the construction industry


Elements and Performance Criteria

ELEMENT

PERFORMANCE CRITERIA

1. Plan and prepare.

1.1. Work instructions and operational details are obtained using relevant information, confirmed and applied for planning and preparation purposes.

1.2. Safety (OHS) requirements are followed in accordance with safety plans and policies.

1.3. Signage and barricade requirements are identified and implemented.

1.4. Tools, plant and equipment selected to carry out tasks are consistent with the requirements of the job, checked for serviceability and any faults are rectified or reported prior to commencement.

1.5. Material quantity requirements are calculated in accordance with plans and specifications and quality requirements.

1.6. Materials appropriate to the work application are identified, obtained, prepared, safely handled and located ready for use.

1.7. Environmental requirements are identified for the project in accordance with environmental plans and regulatory obligations and applied.

2. Confirm the penetration and flashing requirement.

2.1. Type of penetration and flashing is selected to match the particular need and host materials.

2.2. Location of the penetration is identified, set out and confirmed.

2.3. Tools, plant and equipment selected to carry out tasks are consistent with the requirements of the job, checked for serviceability, and any faults are rectified or reported prior to commencement.

3. Complete the penetrations and flashings.

3.1. Penetrations are completed safely and with minimal modification or damage to the host materials.

3.2. Flashings are completed safely and with minimal modification or damage to the host materials.

3.3. Casings, housings or other terminating points are installed and connections made in accordance with state and territory requirements.

3.4. Proprietary sealants or caulking compounds are applied to restore the integrity of the wall or ceiling system.

3.5. Surfaces are prepared for finishing.

4. Clean up.

4.1. Work area is cleared and materials disposed of, reused or recycled in accordance with legislation, regulations, codes of practice and job specification.

4.2. Tools and equipment are cleaned, checked, maintained and stored in accordance with manufacturer recommendations and standard work practices.

Required Skills

Required skills

Required skills for this unit are:

communication skills to:

follow instructions

read and interpret:

documentation from a variety of sources

drawings and specifications

recognise procedures

report faults

enable clear and direct communication, using questioning to identify and confirm requirements, share information, listen and understand

use language and concepts appropriate to cultural differences

use and interpret non-verbal communication, such as hand signals

written skills to record results of checks and tests and relevant work completion procedures

evaluate own actions and make judgments about performance and necessary improvements

identifying and accurately reporting to appropriate personnel any faults in tools, equipment or materials

organisational skills, including the ability to plan and set out work

respond to change and contribute to workplace responsibilities, such as current work site environmental and sustainability frameworks and management systems

teamwork skills to work with others to action tasks and relate to people from a range of cultural and ethnic backgrounds and with varying physical and mental abilities

technological skills to:

use a range of mobile technology, such as two-way radio and mobile phones

voice and hand signals to access and understand site-specific instructions.

Required knowledge

Required knowledge for this unit is:

job safety analysis (JSA) and safe work method statements

materials storage and environmentally friendly waste management

penetration and flashing techniques

plans, drawings and specifications

processes for the calculation of material requirements

quality requirements

services locating techniques

systems and techniques for safe handling of materials

types of services and purposes for which penetrations and flashings are required

types, characteristics, uses and limitations of wall and ceiling lining materials

types, characteristics, uses and limitations of hand and power tools for wall and ceiling lining

wall and ceiling industry terminology

workplace and equipment safety requirements.

Evidence Required

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

This unit of competency could be assessed in the workplace or a close simulation of the workplace environment, provided that simulated or project-based assessment techniques fully replicate construction workplace conditions, materials, activities, responsibilities and procedures.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

A person who demonstrates competency in this unit must be able to provide evidence of the ability to:

locate, interpret and apply relevant information, standards and specifications

comply with site safety plan and OHS legislation, regulations and codes of practice applicable to workplace operations

comply with organisational policies and procedures including quality requirements

safely and effectively operate and use tools, plant and equipment

communicate and work effectively and safely with others

complete a minimum of three penetration and flashing tasks, including:

one for electrical services

one for communication services.

Context of and specific resources for assessment

This competency is to be assessed using standard and authorised work practices, safety requirements and environmental constraints.

Assessment of essential underpinning knowledge will usually be conducted in an off-site context.

Assessment is to comply with relevant regulatory or Australian standards' requirements.

Resource implications for assessment include:

workplace location or simulated workplace

hand and power tools and equipment appropriate to the completion of penetrations and flashings

realistic activities covering the mandatory task requirements

specifications and work instructions.

Assessment of this unit of competency may be in conjunction with assessment of other units commonly performed at the same time in normal job roles.

Reasonable adjustments for people with disabilities must be made to assessment processes where required. This could include access to modified equipment and other physical resources, and the provision of appropriate assessment support.

Method of assessment

Assessment methods must:

satisfy the endorsed Assessment Guidelines of the Construction, Plumbing and Services Training Package

include direct observation of tasks in real or simulated work conditions, with questioning to confirm the ability to consistently identify and correctly interpret the essential underpinning knowledge required for practical application

reinforce the integration of employability skills with workplace tasks and job roles

confirm that competency is verified and able to be transferred to other circumstances and environments.

Validity and sufficiency of evidence requires that:

competency will need to be demonstrated over a period of time reflecting the scope of the role and the practical requirements of the workplace

where the assessment is part of a structured learning experience the evidence collected must relate to a number of performances assessed at different points in time and separated by further learning and practice, with a decision on competency only taken at the point when the assessor has complete confidence in the person's demonstrated ability and applied knowledge

all assessment that is part of a structured learning experience must include a combination of direct, indirect and supplementary evidence.

Assessment processes and techniques should as far as is practical take into account the language, literacy and numeracy capacity of the candidate in relation to the competency being assessed.

Supplementary evidence of competency may be obtained from relevant authenticated documentation from third parties, such as existing supervisors, team leaders or specialist training staff.


Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Information includes:

diagrams or sketches

instructions issued by authorised organisational or external personnel

manufacturer specifications and instructions, where specified

material safety data sheets (MSDS)

memos

regulatory and legislative requirements pertaining to completion of penetrations and flashings

relevant Australian standards

safe work procedures relating to completion of penetrations and flashings

signage

verbal, written and graphical instructions

work bulletins

work schedules, plans and specifications.

Planning and preparation include:

assessment of conditions and hazards

determination of work requirements and safety plans and policies

equipment defect identification

work site inspection.

Safety (OHS) is to be in accordance with state and territory legislation and regulations and project safety plan and may include:

emergency procedures, including extinguishing fires, organisational first aid requirements and evacuation

hazard control

hazardous materials and substances

organisational first aid

PPE prescribed under legislation, regulations and workplace policies and practices

safe operating procedures, including the conduct of operational risk assessment and treatments associated with:

cutting edges

lighting

manual handling

noise, dust and ventilation

power equipment

power leads and sources

traffic control

trip hazards

work site visitors and the public

working at heights

working in confined spaces

working in proximity to others

use of firefighting equipment

use of tools and equipment

workplace environmental requirements and safety.

Tools and equipment include:

broad knives

brooms

electric screw guns

hand and power drills

hand saws

keyhole saws

measuring tapes and rules

paintbrushes

plasterboard hammers

plasterer's trowels

scaffold planks

T squares

taping knives

trestles.

Plant and equipment include:

earth leakage protection

lighting sets

power activated fasteners

power routers

power saws

small compressor air operated

small petrol or diesel engine driven generators.

Quality requirements include relevant regulations, including:

Australian standards

internal company quality policy and standards

manufacturer specifications

workplace operations and procedures.

Materials include:

beads

cement render

fibre cement sheets

finishing materials

plaster compounds

plasterboard

plasterglass sheets

water resistant plasterboard.

Environmental requirements include:

clean-up management

dust and noise

vibration

waste management.

Penetration and flashings include those required for:

communications

control joints

electrical power

plumbing.


Sectors

Unit sector

Construction


Co-Requisites

Nil


Employability Skills

This unit contains employability skills.


Licensing Information

Not Applicable