CPCPFS3012A
Install distribution and range pipes

This unit of competency specifies the outcomes required to install distribution and range pipes to carry all commonly used fire extinguishing agents, above and below ground.

Application

Site location for work application may be either domestic or commercial, and may be a new work site or an existing structure being renovated, extended, restored or maintained.



Elements and Performance Criteria

ELEMENT

PERFORMANCE CRITERIA

1. Prepare for work.

1.1. Approved plans and specifications are obtained from relevant authority.

1.2. Safety (OHS) requirements associated with installing distribution and range pipes, and workplace environmental requirements, are adhered to throughout the work.

1.3. Quality assurance requirements are identified and adhered to in accordance with workplace requirements.

1.4. Tasks are planned and sequenced in conjunction with others involved in or affected by the work.

1.5. Tools and equipment for installing distribution and range pipes, including personal protective equipment, are selected and checked for serviceability.

1.6. Work area is prepared to support efficient installation of distribution and range pipes.

2. Identify installation requirements.

2.1. System requirements are identified from job design criteria, specifications and standards.

2.2. Quantities of materials required are calculated from plans and specifications.

2.3. Allowances for fabrication and assembly are correctly determined and transferred.

2.4. Materials and equipment are identified, ordered and collected in accordance with workplace procedures.

2.5. Materials and equipment are checked for compliance with standards, docket and order form, and for acceptable condition.

3. Install and test piping system.

3.1. Pipework is set out in accordance with drawings, specifications and job instructions.

3.2. Pipe supports and fixings are installed to plans, manufacturer specifications and extinguishing materials.

3.3. Piping and materials are installed in accordance with the design drawings, job specifications and standards.

3.4. Mechanical jointing systems are compliant with standards.

3.5. Pipes are subjected to pressure testing in accordance with standards or job specification.

3.6. Test data is recorded in format required by the job specifications and quality assurance procedures.

3.7. Installation is backfilled in accordance with specifications.

4. Clean up.

4.1. Work area is cleared, with materials disposed of or recycled in accordance with state or territory statutory and regulatory authority legislation.

4.2. Tools and equipment are cleaned, checked, maintained and stored in accordance with manufacturer recommendations and workplace procedures.

4.3. Information is accessed and documentation completed in accordance with regulatory authorities and workplace requirements.

Required Skills

Required skills

Required skills for this unit are:

communication skills to:

access information

complete workplace documentation

determine requirements

enable clear and direct communication, using questioning to identify and confirm requirements, share information, listen and understand

follow and give instructions

plan and sequence tasks with others

read and interpret:

documentation from a variety of sources

drawings and specifications

record test results in writing

use language and concepts appropriate to cultural differences

use and interpret non-verbal communication, such as hand signals

identifying and accurately reporting to appropriate personnel any faults in tools, equipment or materials

installing and testing above ground distribution and range pipe system, fitted with branches, to supply water to a sprinkler system

numeracy skills to apply measurements and calculations

organisational skills, including the ability to plan and set out work

teamwork skills to work with others to action tasks and relate to people from a range of cultural and ethnic backgrounds and with varying physical and mental abilities

technological skills to:

access and understand site-specific instructions in a variety of media

use mobile communication technology.

Required knowledge

Required knowledge for this unit is:

accessing information and the processes for calculating material requirements

characteristics and application of different pipe fittings and fixture supports, including fixing and joining techniques

excavation processes and procedures

job safety analysis (JSA) and safe work method statements (SWMS)

levelling and alignment processes

materials relevant to installation of distribution and range pipes

pressure test systems and procedures

process of installing and testing distribution and range pipes

relevant statutory and authority requirements related to installation of distribution and range pipes

SI system of measurement

structural systems, building materials and building services

workplace and equipment safety requirements.

Evidence Required

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

This unit of competency could be assessed in the workplace or a close simulation of the workplace environment providing that simulated or project-based assessment techniques fully replicate plumbing and services workplace conditions, materials, activities, responsibilities and procedures.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

A person who demonstrates competency in this unit must be able to provide evidence of:

locating, interpreting and applying relevant information, standards and specifications to install and test distribution and range pipes

applying safety requirements throughout the work sequence, including the use of personal protective clothing and equipment

as a minimum the ability to, given the plans and specifications of an automated fire sprinkler system, install and test distribution and range pipes to provide a free-flowing and leak-free water supply to at least three branches to design criteria and standards, ensuring:

correct identification of location, design and details of proposed installation

correct selection and use of appropriate processes, tools and equipment

completing all work to specification

compliance with regulations, standards and organisational quality procedures and processes

communicating and working effectively and safely with others.

Context of and specific resources for assessment

This competency is to be assessed using standard and authorised work practices, safety requirements and environmental constraints.

Assessment of essential underpinning knowledge will usually be conducted in an off-site context.

Assessment is to comply with relevant regulatory or Australian standards' requirements.

Resource implications for assessment include:

an induction procedure and requirement

realistic tasks or simulated tasks covering the minimum task requirements

relevant specifications and work instructions

tools and equipment appropriate to applying safe work practices

support materials appropriate to activity

workplace instructions relating to safe working practices and addressing hazards and emergencies

material safety data sheets

research resources, including industry related systems information.

Reasonable adjustments for people with disabilities must be made to assessment processes where required. This could include access to modified equipment and other physical resources, and the provision of appropriate assessment support.

Method of assessment

Assessment methods must:

satisfy the endorsed Assessment Guidelines of the Construction, Plumbing and Services Training Package

include direct observation of tasks in real or simulated work conditions, with questioning to confirm the ability to consistently identify and correctly interpret the essential underpinning knowledge required for practical application

reinforce the integration of employability skills with workplace tasks and job roles

confirm that competency is verified and able to be transferred to other circumstances and environments.

Validity and sufficiency of evidence requires that:

competency will need to be demonstrated over a period of time reflecting the scope of the role and the practical requirements of the workplace

where the assessment is part of a structured learning experience the evidence collected must relate to a number of performances assessed at different points in time and separated by further learning and practice, with a decision on competency only taken at the point when the assessor has complete confidence in the person's demonstrated ability and applied knowledge

all assessment that is part of a structured learning experience must include a combination of direct, indirect and supplementary evidence.

Assessment processes and techniques should as far as is practical take into account the language, literacy and numeracy capacity of the candidate in relation to the competency being assessed.

Supplementary evidence of competency may be obtained from relevant authenticated documentation from third parties, such as existing supervisors, team leaders or specialist training staff.


Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Safety (OHS) is to be in accordance with commonwealth, state and territory legislation and regulations and may include:

handling of materials

hazard control

personal protective clothing and equipment prescribed under legislation, regulations and workplace policies and practices

safe operating procedures, including recognising and preventing hazards associated with:

hazardous materials and substances

service lines

surrounding structures and facilities

trip hazards

use of tools and equipment

work site visitors and the public

working at heights

working in proximity to others

use of firefighting equipment

use of first aid equipment

workplace environment and safety.

Distribution and range pipes may be installed:

above and below ground.

Environmental requirements cover water quality management and may include:

clean-up protection

stormwater protection

waste management.

Quality assurance requirements may include:

Australian standards

Environment Protection Authority (EPA)

internal company quality assurance policy and risk management strategy

International Standards Organisation

site safety plan

workplace operations and procedures.

Tools and equipment may include:

angle grinders

bending equipment

chain blocks

cutting and threading equipment

elevated work platforms

forklifts

hand and power tools

hand excavation tools

hand trolleys

hoists and jacks

ladders

lifting and load shifting equipment

measuring equipment

mechanical excavation equipment

rollers

scaffolds

testing equipment

welding equipment.

Materials include:

any approved materials.

Extinguishing materials include:

foam

gases

powder

water.

Statutory and regulatory authorities include:

state or territory statutory authority

statutory gasfitting authority

statutory plumbing authority.

Information may include:

charts and hand drawings

diagrams or sketches

instructions issued by authorised organisational or external personnel

manufacturer specifications and instructions

material safety data sheets (MSDS)

memos

organisation work specifications and requirements

regulatory and legislative requirements, particularly those pertaining to:

building codes

OHS and environmental requirements

plumbing regulations

relevant Australian standards

safe work procedures relating to installing distribution and range pipes

signage

verbal, written and graphical instructions

work bulletins

work schedules, plans and specifications.


Sectors

Unit sector

Plumbing and services


Co-Requisites

Nil


Employability Skills

This unit contains employability skills.


Licensing Information

Not Applicable