CPCPCM2043A

Carry out WHS requirements

1

Prepare for work.

1.1

Plans and specifications are obtained and fixture position is determined.

1.2

Work health and safety (WHS) andenvironmental requirements associated with installing sewage discharge pipes are adhered to throughout the work.

1.3

Quality assurance requirements are identified and adhered to according to workplace requirements.

1.4

Tasks are planned and sequenced in conjunction with others involved in or affected by the work and statutory and regulatory authorities’ requirements.

1.5

Tools and equipmentfor installing sewage discharge pipes, including personal protective equipment, are selected and checked for serviceability.

1.6

Work area is prepared to support efficient installation of sewage discharge pipes.

2

Identify installation requirements.

2.1

Position of discharge pipes is determined according to plans and specifications, relevant Australian standards, site requirements and other relevant information and does not cause damage or interference to surrounding structures.

2.2

Quantity and type of materials required are calculated from design drawings and specifications and comply with relevant Australian standards and authorities' requirements.

2.3

Allowances for fabrication and assembly are determined and transferred.

2.4

Materials and equipment are identified, ordered and collected according to workplace procedures.

2.5

Materials and equipment are checked for compliance with relevant Australian standards, docket and order forms, and for acceptable condition.

2.6

Sustainability principles and concepts are observed when preparing for and undertaking work process.

3

Install and test pipe system.

3.1

Pipe systemis set out to comply with plans, specifications and relevant Australian standards.

3.2

Fixings and supports are installed to manufacturer recommendations, job plans and specifications, and relevant Australian standards.

3.3

Pipes are installed and jointed according to relevant Australian standards, without damage or distortion to pipework, surrounding environment and other services.

3.4

Pipe system is tested to comply with relevant Australian standards and adjusted.

4

Clean up.

4.1

Work area is cleared and materials disposed of, reused or recycled according to legislation, regulations, codes of practice and job specification.

4.2

Tools and equipment are cleaned, checked, maintained and stored according to manufacturer recommendations and workplace procedures.

4.3

Documentation is completed according to workplace requirements.

Required skills

communication skills to:

access information

enable clear and direct communication, using questioning to identify and confirm requirements, share information, listen and understand

follow instructions

identify requirements

report faults

use language and concepts appropriate to cultural differences

use and interpret non-verbal communication, such as hand signals

literacy skills to:

complete workplace documentation

read and interpret:

documentation from a variety of sources

plans and specifications

record plans

numeracy skills to apply measurements and calculations

planning and organising skills to:

plan and sequence tasks with others

plan and set out work

teamwork skills to work with others to action tasks and relate to people from a range of cultural and ethnic backgrounds and with varying physical and mental abilities

technical skills to identify and accurately report to appropriate personnel any faults in tools, equipment or materials

technology skills to:

access and understand site-specific instructions in a variety of media

use mobile communication technology

Required knowledge

characteristics and application of different materials, pipe fittings and supports, including fixing and joining techniques

job safety analysis (JSA) and safe work method statements (SWMS)

levelling and alignment processes

process of installing sewage discharge pipes

processes for accessing information and for calculating material requirements

properties and characteristics of sewage, including temperature implications and discharges

relevant statutory requirements related to installing discharge pipes

SI system of measurements

standards applicable to the installation

workplace and equipment safety requirements

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

This unit of competency could be assessed in the workplace or a close simulation of the workplace environment providing that simulated or project-based assessment techniques fully replicate plumbing and services workplace conditions, materials, activities, responsibilities and procedures.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

A person who demonstrates competency in this unit must be able to provide evidence of:

locating, interpreting and applying relevant information, Australian standards and specifications to install sewage discharge pipes

applying safety requirements throughout the work sequence, including electrical safety requirements and the use of personal protective clothing and equipment

given the plans and specifications and using any two approved materials, installing two fixture discharge pipes:

direct to a below-ground drain

direct to drain via elevated pipework, which includes at least one expansion fitting

waste fixture to a drain via a gully (a combination of soil and waste fixtures must be included), ensuring:

application of sustainability principles and concepts

correct identification of location, design and details of proposed installations

correct selection and use of appropriate processes, tools and equipment

completion of all work to specification

compliance with regulations, relevant Australian standards and organisational quality procedures and processes

communicating and working effectively and safely with others.

Context of and specific resources for assessment

This competency is to be assessed using standard and authorised work practices, safety requirements and environmental constraints.

Assessment of essential underpinning knowledge will usually be conducted in an off-site context.

Assessment is to comply with relevant regulatory or Australian standards’ requirements.

Resource implications for assessment include:

an induction procedure and requirement

realistic tasks or simulated tasks covering the minimum task requirements

relevant specifications and work instructions

tools and equipment appropriate to applying safe work practices

support materials appropriate to activity

workplace instructions relating to safe working practices and addressing hazards and emergencies

material safety data sheets

research resources, including industry-related systems information.

Reasonable adjustments for people with disabilities must be made to assessment processes where required. This could include access to modified equipment and other physical resources, and the provision of appropriate assessment support.

Method of assessment

Assessment methods must:

satisfy the endorsed Assessment Guidelines of the Construction, Plumbing and Services Training Package

include direct observation of tasks in real or simulated work conditions, with questioning to confirm the ability to consistently identify and correctly interpret the essential underpinning knowledge required for practical application

reinforce the integration of employability skills with workplace tasks and job roles

confirm that competency is verified and able to be transferred to other circumstances and environments.

Validity and sufficiency of evidence requires that:

competency will need to be demonstrated over a period of time reflecting the scope of the role and the practical requirements of the workplace

where the assessment is part of a structured learning experience the evidence collected must relate to a number of performances assessed at different points in time and separated by further learning and practice, with a decision on competency only taken at the point when the assessor has complete confidence in the person's demonstrated ability and applied knowledge

all assessment that is part of a structured learning experience must include a combination of direct, indirect and supplementary evidence.

Assessment processes and techniques should as far as is practical take into account the language, literacy and numeracy capacity of the candidate in relation to the competency being assessed.

Supplementary evidence of competency may be obtained from relevant authenticated documentation from third parties, such as existing supervisors, team leaders or specialist training staff.

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Work health and safety is to be according to commonwealth, state and territory legislation and regulations and may include:

handling of materials

hazard control

personal protective clothing and equipment prescribed under legislation, regulations and workplace policies and practices

safe operating procedures, including recognising and preventing hazards associated with:

dirt mounds

electricity

hazardous materials and substances

other machines

recently filled trenches

surrounding structure and facilities

traffic control

trip hazards

underground services

use of tools and equipment

work site visitors and the public

working at heights

working in confined spaces

working in proximity to others

use of firefighting equipment

use of first aid equipment

workplace environment and safety.

Environmental requirements cover water quality management and may include:

clean-up protection

stormwater protection

waste management.

Quality assurance requirements may include:

environment policy

Environment Protection Authority (EPA)

internal company quality assurance policy and risk management strategy

International Standards Organisation

site safety plan

workplace operations and procedures.

Statutory and regulatory authorities include:

commonwealth, state or territory, and local authorities administering applicable Acts, regulations and codes of practice.

Tools and equipment may include:

dropsaw

hacksaw

hand and power tools

heating equipment

lifting and load shifting equipment, including:

chain blocks

elevated work platforms

forklifts

hand trolleys

hoists and jacks

limited height scaffolding

rollers

measuring equipment

threading and bending equipment.

Information may include:

charts and hand drawings

instructions issued by authorised organisational or external personnel

job drawings

manufacturer specifications and instructions

material safety data sheets (MSDS)

memos

organisation work specifications and requirements

plans and sketches

regulatory and legislative requirements, particularly those pertaining to:

building codes

WHS and environmental requirements

plumbing regulations

relevant Australian standards

safe work procedures relating to installing sewage discharge pipes

signage

verbal, written and graphical instructions

work bulletins

work schedules, plans and specifications.

Materials may include:

any material authorised for use.

Sustainability principles and concepts:

cover the current and future social, economic and environmental use of resources

may include:

efficient energy use

efficient use and recycling of material

correct handling of hazardous materials

disposing of waste material to ensure minimal environmental impact

selecting appropriate components to ensure minimal environmental impact.

Pipe systems may include:

direct or indirect to drains

direct to stack

elevated pipework.

Functional area

Unit sector

Plumbing and services