This unit supports the attainment of skills and knowledge required for competent workplace performance in the wide variety of flooring technology operations. The competency applies to an on site environment and involves application of skills and knowledge at a sub-trade worker level. These skills and knowledge are to be used within the scope of the individual's job and authority.

Nil

ELEMENT

PERFORMANCE CRITERIA

1. Prepare for the work

1.1. Applicable legislative, OHS and organisational requirements relevant to edge sanding oftimber flooring are verified and complied with

1.2. Instructions and/or plans are read and interpreted to identify process required to complete work tasks

1.3. Timber flooring is checked for contamination and moisture content

1.4. Timber flooring condition is assessed and the extent of floor preparation required to meet job specifications is confirmed

1.5. Timber flooring is inspected for suitability for sanding operations and any pre-sanding tasks are completed

1.6. Mechanical fixings are removed avoiding damage to equipment and surfaces

1.7. Tools, equipment and materials are selected and checked prior to use to ensure that they are appropriate for the work, serviceable and in a safe condition

1.8. The job site is isolated and/or encapsulated to contain dust fallout from sanding operation

1.9. Sequence of work is planned, including the starting point, to ensure efficiency and quality of installation

2. Edge sanding operations

2.1. Edge sanding equipment is set up in accordance with manufacturer instructions and operating procedures

2.2. Emergency stops, gauges, guards and controls are identified and checked

2.3. Equipment settings and adjustments are made and checked

2.4. Sanding papers are selected

2.5. Trial runs are conducted to check machine operations and quality of finished work

2.6. Sanding papers are attached, routinely checked and changed as required

2.7. Edge sanding is completed systematically and effectively within the minimum required timeframe

2.8. Routine lubrication and adjustments to the equipment are completed as required

2.9. Finished timber flooring is cleaned, inspected and any imperfections are rectified following workplace procedures

3. Complete housekeeping

3.1. Unused materials are stored or recycled as required

3.2. Tools and equipment are cleaned and stored appropriately

3.3. Work area is cleaned and rubbish disposed of appropriately

3.4. Workplace documentation is completed

Required skills

collect, organise and understand information related to work orders, basic plans and safety procedures

communicate ideas and information to enable confirmation of work requirements and specifications, coordination of work with site supervisor, other workers and customers, and the reporting of work outcomes and problems

work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity

use pre-checking and inspection techniques to anticipate problems related to edge sanding of timber floors to avoid re-work and wastage

recognise and respond to circumstances outside instructions or personal competence

plan and organise activities, including the preparation and layout of the worksite and the obtaining of equipment and materials to avoid any back tracking, work flow interruptions or wastage

use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate other material requirements

clarify and confirm work instructions

plan work within given task parameters

accept responsibility for given tasks

set, monitor and satisfy personal work goals

satisfy the competency requirements for the job

maintain current knowledge of:

tools and materials

edge sanding techniques

seek learning opportunities

use the limited workplace technology related to the edge sanding of timber floors including tools, equipment, calculators and measuring devices.

Required knowledge

State or Territory OHS legislation, regulations, standards and codes of practice relevant to edge sand timber flooring

organisational and site standards, requirements, policies and procedures for edge sanding of timber flooring

characteristics, requirements and techniques for timber flooring edge sanding

types and uses of relevant tools and equipment used to conduct edge sanding operations

workplace safety system requirements related to edge sanding timber flooring

types of tools and equipment and procedures for their safe use, operation and maintenance

characteristics of materials, products and defects

set up and operation of equipment

products assembly techniques

procedures for the recording, reporting and maintenance of workplace records and information

appropriate mathematical procedures for estimation and measurement

environmental protection requirements

established communication channels and protocols

problem identification and resolution.

The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

Comply with legislation, regulations, standards, codes of practice and established safe practices and procedures for edge sanding timber floors

Interpret work order and locate relevant information

Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment

Follow work instructions, operating procedures and inspection practices to:

prevent damage to goods, equipment and products

maintain required production output and product quality

minimise the risk of injury to self and others

Complete a minimum of two timber flooring preparations requiring edge sanding timber flooring:

to grade the surface

to remove cupping, ridges, high points or deep scratches along the edges of the room, in corners or areas of reduced access such as wardrobes etc.

to blend the floor boards into the body of course and fine sanded timber floor

Work effectively with others

Modify activities to cater for variations in workplace context and environment

Context of, and specific resources for assessment

The application of competency is to be assessed in the workplace or realistically simulated workplace

Assessment is to occur under standard and authorised work practices, safety requirements and environmental constraints

Assessment of essential underpinning knowledge, other than confirmatory questions, will usually be conducted in an off-site context

Assessment is to comply with relevant regulatory or Australian Standards requirements

The following resources should be made available:

workplace location or simulated workplace

materials and equipment relevant to edge sanding timber floors

specifications and work instructions

Method of assessment

Assessment must satisfy the endorsed assessment guidelines of the Furnishing Industry Training Package

Assessment methods must confirm consistency and accuracy of performance (over time and in a range of workplace relevant contexts) together with application of underpinning knowledge

Assessment methods must be by direct observation of tasks and include questioning on underpinning knowledge to ensure its correct interpretation and application

Assessment may be applied under project related conditions (real or simulated) and require evidence of process

Assessment must confirm a reasonable inference that competency is able not only to be satisfied under the particular circumstance, but is able to be transferred to other circumstances

Assessment may be in conjunction with assessment of other units of competency

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Legislative requirements

are to be in accordance with applicable legislation from all levels of government that affect organisational operation. Requirements may include but not be limited to award and enterprise agreements, industrial relations, Australian Standards, confidentiality and privacy, OHS, the environment, equal opportunity, anti-discrimination, relevant industry codes of practice, duty of care and heritage

OHS requirements

are to be in accordance with Commonwealth, State or Territory legislation and regulations, organisational safety policies and procedures. Requirements may include but not be limited to the use of personal protective equipment and clothing, fire fighting equipment, First Aid equipment, hazard and risk control and elimination, control of hazardous materials and substances, manual handling including lifting and carrying

Organisational requirements

may include but not be limited to legal, organisational and site guidelines, policies and procedures relating to own role and responsibility, quality assurance, procedural manuals, quality and continuous improvement processes and standards, OHS, emergency and evacuation, ethical standards, recording and reporting, access and equity principles and practices, equipment use, maintenance and storage, environmental management (waste disposal, recycling and re-use guidelines)

Edge sanding of timber flooring

is to include removal of mechanical fixings, punching of nails, sanding the timber flooring to grade the surface to remove cupping, ridges, high points or deep scratches along the edges of the room, in corners or areas of reduced access such as wardrobes etc. The pattern of sanding should overlap and blend the floor boards into the body of the sanded floor

Instructions

Workplace procedures relating to the use and operation of tools and equipment

Workplace instructions, instructions, including job sheets, plans, drawings and designs

Workplace procedures relating to reporting and communications

Manufacturer instructions for the use of equipment and materials

Mechanical fixings

are to include tacks, nails, staples and screws

Tools and equipment

are to include hammer, scrapers, punches, brooms, vacuums, leads and dust masks

Materials

are to include but are not limited to sanding belts, sanding paper, sanding discs, oil and lubricants

Edge sanding equipment

may include disc, orbital or belt sanders, using a full range of grit papers depending on the sanding process required, oil and lubricants

Unit sector

Flooring Technology

Floor Preparation

This unit contains employability skills.