This unit supports the attainment of skills and knowledge required for competent workplace performance in leadlight and stained glass operations. The requirement to plan, fabricate and install residential lead light and stained glass windows and doors applies to a workshop and onsite environment and involves application of skills and knowledge at a tradesperson level. These skills and knowledge are to be used within the scope of the individual's job and authority. |
Nil | ||
ELEMENT | PERFORMANCE CRITERIA |
1. Plan to fabricate and install | 1.1. Applicable OHS, legislative and organisational requirements relevant to lead light and stained glass operations are verified and complied with 1.2. The process for fabricating and installing lead light and stained glass windows and doors is identified 1.3. Types and quantities of materials required are calculated from plans or work instructions or by measuring the fixture opening 1.4. Cutting lists are prepared from plans, work instructions or measurements of opening to suit the window or door to be installed 1.5. Fittings, fixings and joining devices or materials are selected 1.6. Tools and equipment appropriate to the fixing method are identified |
2. Prepare to fabricate and install | 2.1. Work sequence is determined in a logical order to suit the job 2.2. Tools, equipment and materials are selected and checked prior to use to ensure that they are appropriate for the work, serviceable and in a safe condition 2.3. Components of the lead light and stained glass window or door are checked against specifications or job order |
3. Fabricate and install | 3.1. Materials are cut to cutting list requirements 3.2. Components of lead light and stained glass window or door are assembled 3.3. Fittings are installed to window or door in accordance with workplace procedures or industry practice 3.4. Window or door is installed |
4. Finalise the installation | 4.1. Installed window or door is inspected for quality of work and repaired, re-fabricated or re-installed as required 4.2. Waste and scrap material is removed for disposal/recycling as required 4.3. Work area is cleaned and rubbish disposed of as appropriate 4.4. Tools, equipment and unused materials are cleaned and removed and stored appropriately 4.5. Workplace records are maintained |
|
Required skills |
collect, organise and understand materials technology and information related to the fabrication and installation of residential lead light and stained glass communicate ideas and information to enable confirmation of work requirements and specifications, coordination of work with site supervisor, other workers and customers, and the reporting of work outcomes and problems maintain quality records related to the fabrication and installation of residential lead light and stained glass work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity identify, anticipate and respond to faults in the fabrication and installation of residential lead light and stained glass recognise and respond to circumstances outside instructions or personal competence plan and organise activities including the preparation and layout of own worksite and the obtaining and use of tools and materials to avoid any backtracking, work flow interruptions or wastage use mathematical ideas and techniques to correctly complete measurements, calculate area and volume, estimate work and material requirements clarify and confirm work instructions plan own work within the given task parameters accept responsibility for given tasks set, monitor and satisfy personal work goals satisfy the competency requirements for the job maintain current knowledge of tools and materials maintain current knowledge of the fabrication and installation of residential lead light and stained glass seek learning opportunities use the workplace technology related to the fabrication and installation of residential lead light and stained glass including computers, measuring devices and recording systems |
Required knowledge |
State or Territory OHS legislation, regulations, standards and codes of practice relevant to the full range of processes for lead light and stained glass operations lead light and stained glass windows and doors construction terminology and techniques organisational and site standards, requirements, policies and procedures for fabrication and installation of lead light and stained glass windows and doors types of glass and other materials used in the lead light and stained glass industry, their characteristics, properties, uses and limitations environmental protection requirements relating to the disposal of waste material established communication channels and protocols problem identification and resolution storage systems and labelling procedures for the recording, reporting and maintenance of workplace records and information appropriate mathematical procedures for estimation and measurement |
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package. | |
Critical aspects for assessment and evidence required to demonstrate competency in this unit | Read and interpret a work/job specification Identify a range of lead light and stained glass windows and doors detailing their uses and limitations Identify and explain the properties of lead light and stained glass windows and doors Identify the likely impact of various environmental effects on lead light and stained glass windows and doors Fabricate and install residential lead light and stained glass window and residential lead light and stained glass door Comply with legislation, regulations, standards, codes of practice and established safe practices and procedures for the fabrication and installation of lead light and stained glass windows and doors Communicate effectively and work safely with others in the work area |
Context of, and specific resources for assessment | The application of competency is to be assessed in the workplace or realistically simulated workplace Assessment is to occur under standard and authorised work practices, safety requirements and environmental constraints Assessment of essential underpinning knowledge, other than confirmatory questions, will usually be conducted in an off-site context Assessment is to comply with relevant regulatory or Australian Standards requirements The following resources should be made available: workplace location or simulated workplace materials and equipment relevant to fabricating and installing lead light and stained glass windows or doors specifications and work instructions |
Method of assessment | Assessment must satisfy the endorsed assessment guidelines of the Furnishing Industry Training Package Assessment methods must confirm consistency and accuracy of performance (over time and in a range of workplace relevant contexts) together with application of underpinning knowledge Assessment methods must be by direct observation of tasks and include questioning on underpinning knowledge to ensure its correct interpretation and application Assessment may be applied under project related conditions (real or simulated) and require evidence of process Assessment must confirm a reasonable inference that competency is able not only to be satisfied under the particular circumstance, but is able to be transferred to other circumstances Assessment may be in conjunction with assessment of other units of competency |
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included. | |
OHS requirements | are to be in accordance with Commonwealth, State or Territory legislation and regulations, organisational safety policies and procedures. Requirements may include but not be limited to the use of personal protective equipment and clothing, fire fighting equipment, First Aid equipment, hazard and risk control and elimination of hazardous materials and substances, manual handling including lifting and carrying. |
Legislative requirements | are to be in accordance with applicable legislation from all levels of government that affect organisational operation. Requirements may include but not be limited to award and enterprise agreements, industrial relations, Australian Standards, confidentiality and privacy, OHS, the environment, equal opportunity, anti-discrimination, relevant industry codes of practice, duty of care and heritage. |
Organisational requirements | may include but not be limited to legal, organisational and site guidelines, policies and procedures relating to own role and responsibility, quality assurance, procedural manuals, quality and continuous improvement processes and standards, OHS, emergency and evacuation, ethical standards, recording and reporting, access and equity principles and practices, equipment use, maintenance and storage, environmental management (waste disposal, recycling and re-use guidelines) |
Windows | may include sliding, double hung, casement and awning windows and double glazed windows |
Doors | may include sliding, hinged and bi-fold doors |
Materials | may include but are not limited to aluminium alloys and steel, fasteners, plastics, sealants, tapes, vinyl's, gaskets, timber reveals and flashings may include hardware includes locks, wheels, stays, hinges, springs and balances and any component required for the operation of residential windows and doors may include lead lighting or stained glass panels, annealed glass, safety glass, patterned glass, tinted, heat reflective and insulated glass units |
Tools and equipment | may include assembly benches, drop and up-cut saws, pneumatic, hydraulic and manual presses, frame and sash tooling, copy routers, end millers, crimpers, electric and pneumatic powered drills and screwdrivers, pop rivet guns, glue guns and general hand tools |
Records | may include but not be limited to the product type, size, inspection, inspection outcomes, quality outcomes and storage locations |
Unit sector | Lead Light and Stained Glass |
This unit contains employability skills. |
Not applicable.