Application
This unit of competency covers applying techniques to repair and touch up damaged surfaces.
No licensing, legislative or certification requirements apply to this unit at the time of publication.
Elements and Performance Criteria
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. | ||
1 | Prepare for work | 1.1 | Workplace information, including materials application and safety information, and material safety data sheets (MSDS), is used to inform work practices |
1.2 | Characteristics of the surface and the required surface coating are identified from work orders or instructions | ||
1.3 | Processing and application techniques, time and safety requirements are identified and used for work planning | ||
1.4 | Work health and safety (WHS) requirements, including ventilation requirements and personal protection needs, are observed throughout the work | ||
1.5 | Tools, equipment and accessories are identified and checked for safe and effective operation for the surface coating task | ||
2 | Repair surfaces | 2.1 | Surfaces are checked for contamination and correct preparation according to workplace procedures and standards |
2.2 | Products with surface or other faults are identified and assessed | ||
2.3 | Materials required for repair are selected and prepared | ||
2.4 | Repairs are completed to manufacturer standards and/or industry practices | ||
3 | Prepare for application of materials | 3.1 | Techniques for hand application of materials are identified and selected |
3.2 | Coating materials required are identified and prepared for the surface coating task | ||
3.3 | Trial applications of surface materials are made to check equipment operation, materials consistency and specified surface finish | ||
3.4 | Faults are identified and workplace procedures for rectification are followed | ||
4 | Apply surface coating | 4.1 | Surface coatings are applied according to job instructions, manufacturer specifications and workplace procedures |
4.2 | Coated products are inspected and approved for suitability for further processing | ||
4.3 | Products which do not meet quality specifications are recoated or tagged for further investigation | ||
5 | Clean work area and maintain equipment | 5.1 | Equipment used is cleaned and inspected for serviceable condition and stored appropriately |
5.2 | Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed | ||
5.3 | Work area, including painting locations, is cleaned and returned to approved condition | ||
5.4 | Workplace records are completed | ||
Evidence of Performance
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Repair and finish a minimum of four (4) damaged surfaces, including:
a strip off and re-finish
two (2) touch ups involving different repair techniques
with only one (1) being a metal surface
Maintain application equipment
Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements
Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures
Minimise wastage of resources, including materials, time and money
Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity
Evidence of Knowledge
Repair and touch up techniques
Decontamination materials, techniques and safety requirements
Identification of application techniques
Characteristics of coatings and base materials in terms of toxicity, reactivity, flammability, required viscosity and recoatability
Methods to prevent contamination of surfaces during and after surface coating
Work flow in relation to the application of surface coatings
Assessment Conditions
Assessors must:
hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors
have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification
be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.
Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.
Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.
Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.
Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.
Access is required to surface coating application equipment, coatings, other consumables and materials to be repaired.
Foundation Skills
Foundation skills essential to performance are explicit in the performance criteria of this unit of competency. Detail on appropriate performance levels for each furnishing unit of competency in reading, writing, oral communication and numeracy utilising the Australian Core Skills Framework (ACSF) are provided in the Furnishing Training Package Implementation Guide.
Range Statement
Specifies different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Range is restricted to essential operating conditions and any other variables essential to the work environment. | |
Unit context includes: | WHS requirements, including legislation, building codes, material safety management systems, hazardous and dangerous goods codes, and local safe operating procedures or equivalent work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements work requires individuals to demonstrate some discretion, judgement and problem solving in the application of surface coatings |
Techniques include: | decontamination and repair stripping wash off stoppings epoxy button lac water putty wax plugs and refinishing |
Surface faults include: | machine marks bruising pencil marks grease cross-sanding marks scratches glue marks dirt marks insect and termite holes holes knots blisters rubber marks burns or tears ropiness and foreign matter in the polish |
Surfaces include: | solid timber manufactured board metal |
Tools and equipment include: | brushes rollers soup rubbers paint trays power agitators sanders liquid containers scrapers quirk sticks sandpapers cotton rags hessian steel wool sandpaper abrasive papers |
Materials include: | lacquers paints acrylics enamels one-pot polyurethane methylated spirits pigments spirit colours |
Personal protective equipment includes: | that prescribed under legislation, regulations and enterprise policies and practices |
Information and procedures include: | workplace procedures relating to the use of tools and equipment work instructions, including job sheets, cutting lists, plans, drawings and designs workplace procedures relating to reporting and communication manufacturer specifications and operational procedures |
Sectors
Furniture finishing