Application
This unit of competency covers fabricating synthetic solid surface furniture and furnishing products.
No licensing, legislative or certification requirements apply to this unit at the time of publication.
Elements and Performance Criteria
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. | ||
1 | Prepare for work | 1.1 | Work instructions are used to determine job requirements, including design, tolerances, process, materials, finish and quantity |
1.2 | Fabrication sequence is planned | ||
1.3 | Procedures are determined for checking quality at each stage of the process | ||
1.4 | Work health and safety (WHS) requirements, including personal protection needs, are observed throughout the work | ||
1.5 | Suitable work area is selected for the task | ||
1.6 | Preparatory drawings and set-outs for tasks are completed | ||
1.7 | Cutting list for components is developed | ||
1.8 | Materials are selected following work instructions | ||
1.9 | Tools and equipment suitable for fabrication are identified and checked for safe and effective operation | ||
2 | Complete fabrication | 2.1 | Materials are set out and prepared according to work instructions and components are marked according to industry practices |
2.2 | Tools, machines and equipment are used in accordance with safety requirements and manufacturer specifications | ||
2.3 | Components are fabricated and checked against set-outs for accuracy tolerances, fit and distortion | ||
2.4 | Doors, drawers, shelves or decorative treatments are fitted as required | ||
2.5 | Product is prepared for final finish, including the removal of bruises, scratches, dents and marks | ||
2.6 | Product is checked against plans at identified checkpoints | ||
3 | Finalise operation and maintain equipment | 3.1 | Work area is cleaned, hand and/or power tools and equipment are cleaned, maintained and stored in accordance with workplace procedures |
3.2 | Machinery is cleaned and left in a safe mode | ||
3.3 | Faulty and/or defective equipment is tagged and reported in accordance with workplace practices | ||
3.4 | Unused hardware is collected and stored for re-use or disposal following workplace procedures | ||
3.5 | Waste and scrap materials are dealt with following workplace procedures |
Evidence of Performance
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment or products
maintain required production output and product quality
Fabricate a minimum of three (3) synthetic solid surface material products, including at least one (1) full benchtop
Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements
Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures
Minimise wastage of resources, including materials, time and money
Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity
Evidence of Knowledge
Types, characteristics, uses and limitations of synthetic solid surface materials
Interpretation of plan representation of furniture design
Preparation of drawings and set-outs
Identification of hand and/or power tools, materials, machines, equipment, processes and procedures
Work flow in relation to furniture production
Assessment Conditions
Assessors must:
hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors
have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification
be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.
Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.
Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.
Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.
Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.
Access is required to plans, hand and/or power tools, machines, equipment, materials and a work area.
Foundation Skills
Foundation skills essential to performance are explicit in the performance criteria of this unit of competency. Detail on appropriate performance levels for each furnishing unit of competency in reading, writing, oral communication and numeracy utilising the Australian Core Skills Framework (ACSF) are provided in the Furnishing Training Package Implementation Guide.
Range Statement
Specifies different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Range is restricted to essential operating conditions and any other variables essential to the work environment. | |
Synthetic solid surface products include: | acrylic or polyester sheet-based materials |
Synthetic solid surface products include: | benchtops edges sinks bowls other containers and waterproof wall treatments |
Unit context includes: | WHS requirements, including legislation, building codes, material safety management systems, hazardous substances and dangerous goods code, and local safe operating procedures work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements work involves reading and interpreting plans, developing set-outs, using hand and/or power tools, equipment and operating machinery |
Tools and equipment include: | measuring tapes or rulers hammers mallets squares bevels chisels planes hand saws power saws power drills/screwdrivers air compressor and hoses clamps screwdrivers pincers |
Machines include: | panel saws routers edge moulders point to point heat applicators sanding and buffing machines |
Materials include: | synthetic solid surface materials timber manufactured board glues screws nails dowels knockdown fittings |
Personal protective equipment includes: | that prescribed under legislation, regulations and enterprise policies and practices |
Information and procedures include: | workplace procedures relating to the use of tools and equipment work instructions, including job sheets, cutting lists, plans, drawings and designs workplace procedures relating to reporting and communication manufacturer specifications and operational procedures |
Sectors
Furniture Making