Application of this unit
This competency applies to operators who are required to apply knowledge of materials, product purpose and processes to the operation of injection blow moulding equipment. The key factors are the production of material meeting quality standards and product requirements and the recognition and resolving of a range of routine and non-routine problems.
The operator will:
check job sheets for work requirements
recognise hazards and taking appropriate action
start up and shut down injection blow moulding equipment
monitor injection blow moulding equipment operation and report process variations
check product for quality and conformity to specifications
discard non-conforming products, ensuring re-use where possible
identify and take action on routine process problems
complete logs and reports.
This unit does not cover die setting, refer to PMAPREP304C Change dies
Prerequisites
This unit of competency has the prerequisite of PMBPROD270A Operate injection blow moulding equipment.
ELEMENT ELEMENT | PERFORMANCE CRITERIA Performance criteria describe the required performance needed to demonstrate achievement of the element. Assessment of performance is to be consistent with the evidence guide. |
1. Plan own work requirements. | 1.1 Identify the most appropriate equipment to be used for production process, upstream and downstream operations from production plan or request. 1.2 Identify and check materials required, including additives and their amounts or percentages. 1.3 Implement measures to control identified hazards in line with procedures and duty of care. 1.4 Identify requirements for materials, quality, production and equipment checks. |
2. Start up injection blow moulding process to procedures | 2.1 Identify process settings required for product. 2.2 Set injection blow moulding process to required settings. 2.3 Check materials are correct. 2.4 Take appropriate action for non-conforming materials. 2.5 Set up date, batch and materials markings as required. 2.6 Complete pre-start checks. 2.7 Start up extrusion process. |
3. Operate and make adjustments to the injection blow moulding process to procedures. | 3.1 Operate extrusion process, noting key variables. 3.2 Monitor controls/displays/terminals for production and process data. 3.3 Take samples as required and identify product out of specification. 3.4 Monitor product/process quality. 3.5 Make adjustments to remedy faults and nonconformity as required. 3.6 Maintain continuity of process. 3.7 Adjust process to minimise scrap and trim. 3.8 Clean, adjust and lubricate equipment as required. 3.9 Pause equipment, or stop equipment in an emergency, as required. |
4. Anticipate and solve problems. | 4.1 Recognise a problem or a potential problem. 4.2 Determine problems needing priority action. 4.3 Refer problems outside area of responsibility to appropriate person, with possible causes. 4.4 Seek information and assistance as required to solve problems. 4.5 Solve problems within area of responsibility. 4.6 Follow through items initiated until final resolution has occurred. |
This describes the essential skills and knowledge and their level required for this unit.
Application of knowledge of the materials, equipment and process sufficient to recognise material and equipment conditions which may lead to out of specification production. For example foreign material in the polymer feed leading to black spots in the product.
Knowledge of organization procedures, quality requirements at each production stage and relevant regulatory requirements along with the ability to implement them within appropriate time constraints and work standards.
Application of the knowledge of managing risks using the hierarchy of controls applied to the injection blow moulding process. Application of approved hazard control, safety procedures, the use of PPE in relation to handling materials, equipment operation and clean-up.
Knowledge as a basis for solving processing and material problems, including:
characteristics of materials and behaviour in relation to heat, pressure, flow rate and time
function and operating principles of injection blow moulding equipment, machine components and ancillary equipment
impact of machine speed, temperature, pressure, time during cycles on product quality and production output
nature of mechanical, hydraulic, pneumatic, electrical and electronic principles which affect machine operation and product development
injection blow moulding cycle and the importance of machine set-up and warm-up for effective processing of materials
impact of variations in raw materials and equipment operation in relation to final product
changes to materials at various stages of production
waste management and importance of non-conforming materials
polymer properties and their interactions with process conditions
relationships between polymer properties and process conditions
changes to polymer properties to better suit process requirements
product problems related to polymer properties
product problems related to process conditions
adjustments to process conditions to meet polymer and product requirements
Competence also includes the ability to:
plan own work, including predicting consequences and identifying improvements
maintain output and product quality using appropriate instruments, controls, test information and readings
identify and describe own role and role of others involved directly in the injection blow moulding process
identify factors which may affect product quality or production output and appropriate remedies
identify when assistance is required to solve problems
quality requirements at each production stage.
Language, literacy and numeracy requirements
This unit requires the ability to read and interpret typical product specifications, job sheets and material labels as provided to operators.
Writing is required to the level of completing workplace forms and production reports.
Basic numeracy is required, eg to determine how many 2 kg, 3 kg and 5 kg bags are needed to make up a requirement for 50 kg.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, the range statement and the assessment guidelines for this training package.
Overview of assessment
A holistic approach should be taken to the assessment.
Assessors must be satisfied that the person can consistently perform the unit as a whole, as defined by the Elements, Performance Criteria and skills and knowledge.
Where the assessee does not currently posses evidence of competency in PMBPROD270B Operate injection blow moulding equipment, it may be co-assessed with this unit.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
It is essential that competence is demonstrated in the knowledge and skills defined in this unit. These may include the ability to:
identify critical materials properties and injection blow moulding process characteristics in relation to the process requirements and the end product
plan own work process within workplace procedures
explain the reasons for the steps in the process
take appropriate action to observe equipment, materials and products for out of specification results, make adjustments and identify problems to be reported.
Consistent performance should be demonstrated. For example, look to see that:
production quality and output standards are met consistently
problems are anticipated from process observations
problems are efficiently resolved
the process runs consistently and smoothly
Assessment method and context
It is preferred that assessment takes place on an industrial extruder in a work-like environment.
Competence in this unit may be assessed:
using an appropriate, industrial injection blow moulding machine
in a situation allowing for the generation of evidence of the ability to recognise, anticipate and respond to problems
by using a suitable simulation and/or a range of case studies/scenarios
through a combination of these techniques.
In all cases it is expected that practical assessment will be combined with targeted questioning to assess the underpinning knowledge and theoretical assessment will be combined with appropriate practical/simulation or similar assessment. Assessors need to be aware of any cultural issues that may affect responses to questions.
Assessment processes and techniques must be culturally appropriate and appropriate to the oracy, language and literacy capacity of the assessee and the work being performed.
Specific resources for assessment
This section should be read in conjunction with the Range Statement for this unit of competency. Resources required include suitable access to an operating plant or equipment that allows for appropriate and realistic simulation. A bank of case studies/scenarios and questions will also be required to the extent that they form part of the assessment method. Questioning may take place either in the workplace, or in an adjacent, quiet facility such as an office or lunchroom. No other special resources are required.
Access must be provided to appropriate learning and/or assessment support when required. Where applicable, physical resources should include equipment modified for people with disabilities.
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts.
Where reference is made to industry codes of practice and/or Australian/international standards, the latest version must be used.
Context
This competency applies to all injection blow moulding within the plastics and rubber industries. It includes the operation of all relevant additional equipment where that equipment is integral to the injection blow moulding process.
Procedures
All operations are performed in accordance with procedures.
Procedures include all relevant workplace procedures, work instructions, temporary instructions and relevant industry and government codes and standards.
Tools and equipment
This unit of competency includes use of equipment and tools such as:
electrical, pneumatic, mechanical, electromechanical and hydraulic injection blow moulding machines and components such as base, frame, feed hoppers and material supply mechanisms, barrel and screw plastification unit, injection blow units, die/ mould tool
additional equipment, including chillers/cooling towers, die heating equipment, hopper driers, mixing hoppers, dehumidifying driers, air compressors, dosing machines, colour blending equipment and conveyors
hand tools used in the injection blow moulding process
material loading equipment used for loading of raw materials
relevant personal protective equipment.
Hazards
Typical hazards include:
spills
dusts/vapours
slip and fall, particularly due to spilt granules
temperature
hazardous materials
manual handling hazards
equipment operations.
Problems
'Anticipate and solve problems' means resolve a wide range of routine and non-routine problems, using product and process knowledge to develop solutions to problems which do not have a known solution/a solution recorded in the procedures.
Typical process and product problems may include:
routine and non-routine product injection blow moulding faults - short mouldings, sink marks, voids, burn marks, mica and splash marks, silver streaking, blistering, flow marks, poor surface finish, warping, windows, erratic cycles, poor colour dispersion, ejection damage, colour contamination, black spots and other defects
machine malfunction
mould/tooling problems
variations in materials and/or contamination of materials
processing problems.
Variables
Key variables to be monitored include:
operating temperatures
speed
hunt or sprue break pressures
colour
cushion specification
cycle time
output rate
product weight
product integrity and general conformance to specification/sample.
Not applicable.
The required outcomes described in this unit contain applicable Employability Skills. The Employability Skills Summary of the qualification(s) in which this unit is packaged will assist in identifying Employability Skill requirements.
Not applicable.