UEENEEH122A
Fault find and repair remote control apparatus

1)Scope:1.1) DescriptorThis unit covers fault finding and repair in remote control apparatus and devices. The unit encompasses safe working practices, interpreting circuit diagrams, applying knowledge of remote control to logical fault finding procedures, conducting repairs, safety and functional testing and completing the necessary service documentation.

Application

2)

This unit is intended for competency development entry-level employment based programs incorporated in approved contracts of training or approved training programs. It may also used to augment previously acquired competencies.


Prerequisites

Prerequisite Unit(s)

4)

Competencies

4.1)

Granting competency in this unit shall be made only after competency in the following unit(s) has/have been confirmed.

UEENEEE101A

Apply Occupational Health and Safety regulations, codes and practices in the workplace

UEENEEE102A

Fabricate, assemble and dismantle utilities industry components

UEENEEH102A

Repairs basic electronic apparatus faults by replacement of components

UEENEEH111A

Troubleshoot single phase input d.c. power supplies

UEENEEH112A

Troubleshoot digital sub-systems

UEENEEH113A

Troubleshoot amplifier circuits

UEENEEH138A

Fault find and repair complex power supplies

AND

UEENEEH114A

Troubleshoot resonance circuits in an electronic apparatus

UEENEEE104A

Solve problems in d.c. circuits

UEENEEH169A

Solve problems in basic electronic circuits

OR

UEENEEE104A

Solve problems in d.c. circuits

UEENEEG101A

Solve problems in electromagnetic devices and related circuits

UEENEEG102A

Solve problems in low voltage a.c. circuits

For the full prerequisite chain details for this unit please refer to Table 2 in Volume 1, Part 2

Literacy and numeracy skills

4.2)

Participants are best equipped to achieve competency in this unit if they have reading, writing and numeracy skills indicated by the following scales. Description of each scale is given in Volume 2, Part 3 ‘Literacy and Numeracy’

Reading

3

Writing

3

Numeracy

3


Elements and Performance Criteria

ELEMENT

PERFORMANCE CRITERIA

1

Prepare to find and repair faults.

1.1

OHS procedures for a given work area are identified, obtained and understood.

1.2

OHS risk control measures and procedures are followed in preparation for the work.

1.3

The nature of the fault is obtained from documentation, work supervisor and customer to establish the scope of work to be undertaken.

1.4

Advice is sought from the work supervisor to ensure the work is co-ordinated effectively with others.

1.5

Sources of materials that may be required for the work are established in accordance with established procedures.

1.6

Tools, equipment and testing devices needed to carry out the work are obtained in accordance with established procedures and checked for correct operation and safety.

2

Find and repair faults.

2.1

OHS risk control measures and procedures for carrying out the work are followed.

2.2

Apparatus is checked as being isolated where necessary in strict accordance OHS requirements and procedures.

2.3

Fault finding is approached methodically drawing on knowledge of remote control apparatus using measured and calculated values of operating parameters and referenced to manufacturer’s specifications.

2.4

Equipment components are dismantled where necessary and parts stored to protect them against loss or damage.

2.5

Faulty components are rechecked and their fault status confirmed.

2.6

Faulty components are readjusted or replace in accordance with established procedures.

2.7

Effectiveness of the repaired component is tested in accordance with established procedures.

2.8

Apparatus is reassembled, finally tested and prepared for return to customer.

2.9

Unexpected situations are dealt with safely and with the approval of an authorised person.

2.10

Fault finding and repair activities are carried out efficiently without waste of materials or damage to apparatus and the surrounding environment or services and using sustainable energy practices.

3

Completion and report fault finding and repair activities.

3.1

OHS work completion risk control measures and procedures are followed.

3.2

Work area is cleaned and made safe in accordance with established procedures.

3.3

Written justification is made for repairs to apparatus including components and materials used.

3.4

Acceptance that the reported fault(s) have been repaired is sought from an appropriate person in accordance with established procedures.

Required Skills

8) This describes the essential skills and knowledge and their level, required for this unit.

Evidence shall show that knowledge has been acquired of safe working practices and finding and repairing faults in remote control apparatus.

All knowledge and skills detailed in this unit should be contextualised to current industry practices and technologies.

KS01-EH122A Hand held remote control units

Evidence shall show an understanding of hand held remote control unit fault finding and repair, applying safe working practices and relevant Standards, Codes and Regulations to an extent indicated by the following aspects:

T1. Remote control requirements

Specifications

multiple systems

code formats

bit sync

system address

commands, timing (clock accuracy)

modulation system

infrared system

transmission errors

methods used to reduce battery power

key scanning and displays

T2. Data monitoring

Points

timing and amplitude specifications

triggering of serial data

data/graticule alignment

identify and decode start bits

system address bits, command bits

stop bits

load and other bits

T3. Remote control measurements

battery voltage range, stand-by current and transmit current

DC voltage and waveforms on IC pins

Frequencies

T4. System controller requirements including remote, local, main housekeeping.

T5. Methods of inter-chip data communications

T6. Fault identification and repair

Evidence Required

9) The evidence guide provides advice on assessment and must be read in conjunction with the Performance Criteria, Required Skills and Knowledge, the Range Statement and the Assessment Guidelines for this Training Package. .

The Evidence Guide forms an integral part of this unit. It must be used in conjunction with all parts of the unit and performed in accordance with the Assessment Guidelines of this Training Package.

Overview of Assessment

9.1)

Longitudinal competency development approaches to assessment, such as Profiling, require data to be reliably gathered in a form that can be consistently interpreted over time. This approach is best utilised in Apprenticeship programs and reduces assessment intervention. It is the Industry-preferred model for apprenticeships. However, where summative (or final) assessment is used it must include the application of the competency in the normal work environment or, at a minimum, the application of the competency in a realistically simulated work environment. It is recognised that, in some circumstances, assessment in part or full can occur outside the workplace. However, it must be in accord with industry and regulatory policy.

Methods chosen for a particular assessment will be influenced by various factors. These include the extent of the assessment, the most effective locations for the assessment activities to take place, access to physical resources, additional safety measures that may be required and the critical nature of the competencies being assessed.

The critical safety nature of working with electricity, electrical equipment, gas or any other hazardous substance/material carries risk in deeming a person competent. Sources of evidence need to be ‘rich’ in nature to minimise error in judgment.

Activities associated with normal everyday work influence decisions about how/how much the data gathered will contribute to its ‘richness’. Some skills are more critical to safety and operational requirements while the same skills may be more or less frequently practised. These points are raised for the assessors to consider when choosing an assessment method and developing assessment instruments. Sample assessment instruments are included for Assessors in the Assessment Guidelines of this Training Package.

Critical aspects of evidence required to demonstrate competency in this unit

9.2)

Before the critical aspects of evidence are considered all prerequisites shall be met.

Evidence for competence in this unit shall be considered holistically. Each Element and associated performance criteria shall be demonstrated on at least two occasions in accordance with the ‘Assessment Guidelines – UEE11’. Evidence shall also comprise:

A representative body of work performance demonstrated within the timeframes typically expected of the discipline, work function and industrial environment. In particular this shall incorporate evidence that shows a candidate is able to:

Implement Occupational Health and Safety workplace procedures and practices, including the use of risk control measures as specified in the performance criteria and range statement

Apply sustainable energy principles and practices as specified in the performance criteria and range statement

Demonstrate an understanding of the essential knowledge and associated skills as described in this unit. It may be required by some jurisdictions that RTOs provide a percentile graded result for the purpose of regulatory or licensing requirements.

Demonstrate an appropriate level of skills enabling employment

Conduct work observing the relevant Anti Discrimination legislation, regulations, polices and workplace procedures

Demonstrated consistent performance across a representative range of contexts from the prescribed items below:

Find and repair faults in remote control apparatus as described in 8) and including:

A

Using methodical fault finding techniques.

B

Finding faults efficiently.

C

Remove/adjusting/replacing components without damage.

D

Testing equipment operation.

E

Providing written justification for the repairs and obtain acceptance of repairs.

F

Dealing with unplanned events by drawing on essential knowledge and skills to provide appropriate solutions incorporated in a holistic assessment with the above listed items.

Note:

Successful completion of relevant vendor training may be used to contribute to evidence on which competency is deemed. In these cases the alignment of outcomes of vendor training with performance criteria and critical aspects of evidence shall be clearly identified.

Context of and specific resources for assessment

9.3)

This unit should be assessed as it relates to normal work practice using procedures, information and resources typical of a workplace. This should include:

OHS policy and work procedures and instructions.

Suitable work environment, facilities, equipment and materials to undertake actual work as prescribed by this unit.

These should be part of the formal learning/assessment environment.

Note:

Where simulation is considered a suitable strategy for assessment, conditions must be authentic and as far as possible reproduce and replicate the workplace and be consistent with the approved industry simulation policy.

The resources used for assessment should reflect current industry practices in relation to finding and repairing fault in remote control apparatus

Method of assessment

9.4)

This unit shall be assessed by methods given in Volume 1, Part 3 ‘Assessment Guidelines’.

Note:

Competent performance with inherent safe working practices is expected in the industry to which this unit applies. This requires that the specified essential knowledge and associated skills are assessed in a structured environment which is primarily intended for learning/assessment and incorporates all necessary equipment and facilities for learners to develop and demonstrate the essential knowledge and skills described in this unit.

Concurrent assessment and relationship with other units

9.5)

For optimisation of training and assessment effort, competency development in this unit may be arranged concurrently with unit:

UEENEEH112A

Troubleshoot digital sub-systems

UEENEEH113A

Troubleshoot amplifiers in an electronic apparatus

UEENEEH115A

Develop software solutions for microcontroller based systems

UEENEEH138A

Fault find and repair complex power supplies

The critical aspects of occupational health and safety covered in unit UEENEEE101A and other discipline specific occupational health and safety units shall be incorporated in relation to this unit.


Range Statement

10) This relates to the unit as a whole providing the range of contexts and conditions to which the performance criteria apply. It allows for different work environments and situations that will affect performance.

This unit shall be demonstrated in relation to finding and repairing at least four faults in two different types of remote control devices.

Generic terms used throughout this Vocational Standard shall be regarded as part of the Range Statement in which competency is demonstrated. The definition of these and other terms that apply are given in Volume 2, Part 2.1.


Sectors

Not applicable.


Employability Skills

5)

This unit contains Employability Skills

The required outcomes described in this unit of competency contain applicable facets of Employability Skills. The Employability Skills Summary of the qualification in which this unit of competency is packaged will assist in identifying Employability Skill requirements.


Licensing Information

License to practice

3)

The skills and knowledge described in this unit do not require a license to practice in the workplace provided equipment is not connected to installation wiring at voltage above 50 V a.c. or 120 V d.c. However other conditions may apply in some States/Territories subject to regulations related to electrical work.

Practice in the workplace and during training is also subject to regulations directly related to occupational health and safety and where applicable contracts of training such as apprenticeships.

Note:

1. Compliance with permits may be required in various jurisdictions and typically relates to the operation of plant, machinery and equipment such as elevating work platforms, powder operated fixing tools, power operated tools, vehicles, road signage and traffic control, lifting equipment and the like. Permits may also be required for some work environments such as confined spaces, working aloft, near live electrical apparatus and site rehabilitation.

2. Compliance may be required in various jurisdictions relating to currency in First Aid, confined space, lifting and risk safety measures.