2)

This unit is intended as an additional competency to relevant competencies previously acquired. It is suitable for employment-based programs under an approved contract of training at the aligned AQF 4 level or higher.

Prerequisite Unit(s)

4)

Competencies

4.1)

Granting competency in this unit shall be made only after competency in the following unit(s) has/have been confirmed.

UEENEEH118A Fault find and repair electronic apparatus

For the full prerequisite chain details for this unit please refer to Table 2 in Volume 1, Part 2

Literacy and numeracy skills

4.2)

Participants are best equipped to achieve competency in this unit if they have reading, writing and numeracy skills indicated by the following scales. Description of each scale is given in Volume 2, Part 3 ‘Literacy and Numeracy’

Reading

4

Writing

4

Numeracy

4

ELEMENT

PERFORMANCE CRITERIA

1

Prepare to diagnose and rectify faults

1.1

OHS procedures for a given work area are obtained and understood.

1.2

Established OHS risk control measures and procedures are followed in preparation for the work.

1.3

Safety hazards that have not previously been identified are documented and risk control measures devised and implemented in consultation with appropriate personnel.

1.4

The extent of faults is determined from reports and other documentation and from discussion with appropriate personnel.

1.5

Appropriate personnel are consulted to ensure the work is co-ordinated effectively with others involved on the work site.

1.6

Tools, equipment and testing devices needed to diagnose faults are obtained in accordance with established procedures and checked for correct operation and safety.

2

Diagnose and rectify faults

2.1

OHS risk control measures and procedures for carrying out the work are followed.

2.2

The need to test or measure live is determined in strict accordance with OHS requirements and when necessary conducted within established safety procedures.

2.3

Circuits/machines/plant are checked as being isolated where necessary in strict accordance OHS requirements and procedures.

2.4

Logical diagnostic methods are applied to diagnose camera circuit’s faults employing measurements of circuit operating parameters referenced to camera operating specifications.

2.5

Suspected fault scenarios are tested as being the source of camera circuit problems.

2.6

Faults in the electronic components of the camera circuits are rectified to raise camera circuits to its operation standard.

2.7

Circuits are tested to verify that the camera operates as intended and to specified requirements.

2.8

Decisions for dealing with unexpected situations are made from discussions with appropriate persons and consistent with job specifications and requirements.

2.9

Diagnosis and rectification activities are carried out efficiently without waste of materials or damage to apparatus and the surrounding environment or services and using sustainable energy practices.

3

Complete and report fault diagnosis and rectification activities

3.1

OHS work completion risk control measures and procedures are followed.

3.2

Work site is made safe in accordance with established safety procedures.

3.3

Rectification of faults is documented in accordance with established procedures.

3.4

Appropriate person or persons notified, in accordance with established procedures, that camera circuit faults have been rectified.

8) This describes the essential skills and knowledge and their level, required for this unit.

Evidence shall show that knowledge has been acquired of safe working practices and diagnosing and rectifying faults in camera circuits.

All knowledge and skills detailed in this unit should be contextualised to current industry practices and technologies.

KS01-EH178A Camera circuits and equipment diagnostics

Evidence shall show an understanding of camera circuits and equipment diagnostics, applying safe working practices and relevant Standards, Codes and Regulations to an extent indicated by the following aspects:

T1. Camcorders and digital cameras encompassing:

Operation of camera circuits

Recording media, standards and formats

Pick up tubes and charge coupled devices

Operation of optical transducers, lenses

Colour separation techniques and signal processing

Charge coupled devices

Mechanics and adjustments

Power supplies and batteries

MPEG capability

T2. Camera circuit diagnosis encompassing:

Sub-system components (i.e. functional blocks) and their operating parameters

Environment factors effecting system performance

Typical faults, their symptoms and cause.

Fault diagnosis procedures and testing

Sub-system adjustments

T3. OHS enterprise responsibilities encompassing:

Provisions of relevant health and safety legislation

Principles and practice of effective occupational health and safety management

Management arrangements relating to regulatory compliance

Enterprise hazards and risks, control measures and relevant expertise required

Characteristics and composition of workforce and their impact on occupational health and safety management

Relevance of enterprise management systems to occupational health and safety management

Analysis of working environment and design of appropriate occupational health and safety management systems

Analysis of relevant data and evaluation of occupational health and safety system effectiveness

Assess resources to establish and maintain occupational health and safety management systems.

9) The evidence guide provides advice on assessment and must be read in conjunction with the Performance Criteria, Required Skills and Knowledge, the Range Statement and the Assessment Guidelines for this Training Package. .

The Evidence Guide forms an integral part of this unit. It must be used in conjunction with all parts of the unit and performed in accordance with the Assessment Guidelines of this Training Package.

Overview of Assessment

9.1)

Longitudinal competency development approaches to assessment, such as Profiling, require data to be reliably gathered in a form that can be consistently interpreted over time. This approach is best utilised in Apprenticeship programs and reduces assessment intervention. It is the Industry-preferred model for apprenticeships. However, where summative (or final) assessment is used it must include the application of the competency in the normal work environment or, at a minimum, the application of the competency in a realistically simulated work environment. It is recognised that, in some circumstances, assessment in part or full can occur outside the workplace. However, it must be in accord with industry and regulatory policy.

Methods chosen for a particular assessment will be influenced by various factors. These include the extent of the assessment, the most effective locations for the assessment activities to take place, access to physical resources, additional safety measures that may be required and the critical nature of the competencies being assessed.

The critical safety nature of working with electricity, electrical equipment, gas or any other hazardous substance/material carries risk in deeming a person competent. Sources of evidence need to be ‘rich’ in nature to minimise error in judgment.

Activities associated with normal everyday work influence decisions about how/how much the data gathered will contribute to its ‘richness’. Some skills are more critical to safety and operational requirements while the same skills may be more or less frequently practised. These points are raised for the assessors to consider when choosing an assessment method and developing assessment instruments. Sample assessment instruments are included for Assessors in the Assessment Guidelines of this Training Package.

Critical aspects of evidence required to demonstrate competency in this unit

9.2)

Before the critical aspects of evidence are considered all prerequisites shall be met.

Evidence for competence in this unit shall be considered holistically. Each Element and associated performance criteria shall be demonstrated on at least two occasions in accordance with the ‘Assessment Guidelines – UEE11’. Evidence shall also comprise:

A representative body of work performance demonstrated within the timeframes typically expected of the discipline, work function and industrial environment. In particular this shall incorporate evidence that shows a candidate is able to:

Implement Occupational Health and Safety workplace procedures and practices, including the use of risk control measures as specified in the performance criteria and range statement

Apply sustainable energy principles and practices as specified in the performance criteria and range statement

Demonstrate an understanding of the essential knowledge and associated skills as described in this unit. It may be required by some jurisdictions that RTOs provide a percentile graded result for the purpose of regulatory or licensing requirements.

Demonstrate an appropriate level of skills enabling employment

Conduct work observing the relevant Anti Discrimination legislation, regulations, polices and workplace procedures

Demonstrated consistent performance across a representative range of contexts from the prescribed items below:

Diagnose and rectify faults in camera circuits as described in 8) and including:

Applying logical diagnostic methods.

Using fault scenarios to test the source of circuit faults.

Identifying the cause faults using logical diagnostic methods.

Rectifying faults effectively.

Verifying that the camera operates correctly.

Documenting fault rectification.

Dealing with unplanned events by drawing on essential knowledge and skills to provide appropriate solutions incorporated in a holistic assessment with the above listed items.

Note:

Successful completion of relevant vendor training may be used to contribute to evidence on which competency is deemed. In these cases the alignment of outcomes of vendor training with performance criteria and critical aspects of evidence shall be clearly identified.

Context of and specific resources for assessment

9.3)

This unit should be assessed as it relates to normal work practice using procedures, information and resources typical of a workplace. This should include:

OHS policy and work procedures and instructions.

Suitable work environment, facilities, equipment and materials to undertake actual work as prescribed by this unit.

These should be part of the formal learning/assessment environment.

Note:

Where simulation is considered a suitable strategy for assessment, conditions must be authentic and as far as possible reproduce and replicate the workplace and be consistent with the approved industry simulation policy.

The resources used for assessment should reflect current industry practices in relation to diagnosing and rectifying faults in camera circuits.

Method of assessment

9.4)

This unit shall be assessed by methods given in Volume 1, Part 3 ‘Assessment Guidelines’.

Note:

Competent performance with inherent safe working practices is expected in the industry to which this unit applies. This requires that the specified essential knowledge and associated skills are assessed in a structured environment which is primarily intended for learning/assessment and incorporates all necessary equipment and facilities for learners to develop and demonstrate the essential knowledge and skills described in this unit.

Concurrent assessment and relationship with other units

9.5)

There are no concurrent assessment recommendations for this unit.

The critical aspects of occupational health and safety covered in unit UEENEEE101A and other discipline specific occupational health and safety units shall be incorporated in relation to this unit.

10) This relates to the unit as a whole providing the range of contexts and conditions to which the performance criteria apply. It allows for different work environments and situations that will affect performance.

This unit shall be demonstrated using a representative range of camera circuits by diagnosing and rectifying at least four circuit faults in two different types of cameras.

Generic terms used throughout this Vocational Standard shall be regarded as part of the Range Statement in which competency is demonstrated. The definition of these and other terms that apply are given in Volume 2, Part 2.1.

5)

This unit contains Employability Skills

The required outcomes described in this unit of competency contain applicable facets of Employability Skills. The Employability Skills Summary of the qualification in which this unit of competency is packaged will assist in identifying Employability Skill requirements.

License to practice

3)

The skills and knowledge described in this unit do not require a license to practice in the workplace provided equipment is not connected to installation wiring at voltage above 50 V a.c. or 120 V d.c. However other conditions may apply in some States/Territories subject to regulations related to electrical work.

Practice in the workplace and during training is also subject to regulations directly related to occupational health and safety and where applicable contracts of training such as apprenticeships.

Note:

1. Compliance with permits may be required in various jurisdictions and typically relates to the operation of plant, machinery and equipment such as elevating work platforms, powder operated fixing tools, power operated tools, vehicles, road signage and traffic control, lifting equipment and the like. Permits may also be required for some work environments such as confined spaces, working aloft, near live electrical apparatus and site rehabilitation.

2. Compliance may be required in various jurisdictions relating to currency in First Aid, confined space, lifting and risk safety measures