The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!
From the Wiki University
What evidence can you provide to prove your understanding of each of the following citeria?
Prepare to dismantle engine block and sub-assemblies
|
|
Nature and scope of work requirements are identified and confirmed Completed |
Evidence:
|
OH&S requirements and personal protection needs are observed throughout the work Completed |
Evidence:
|
Procedures and information such as workshop manuals, specifications, and tooling, are sourced Completed |
Evidence:
|
Method options are analysed and those most appropriate to the circumstances are selected and prepared Completed |
Evidence:
|
Support equipment is identified and prepared Completed |
Evidence:
|
Engine block and sub-assemblies are cleaned Completed |
Evidence:
|
Dismantle engine block and sub-assemblies
|
|
Correct information is accessed and interpreted from manufacturer/component supplier specifications Completed |
Evidence:
|
Engine block and sub-assemblies are dismantled using approved methods and tooling/equipment Completed |
Evidence:
|
Engine block and sub-assemblies are dismantled without causing damage to any component or system Completed |
Evidence:
|
Component parts are cleaned in preparation for evaluation Completed |
Evidence:
|
Dismantling/cleaning activities are carried out according to industry regulations/guidelines and enterprise procedures/ policies Completed |
Evidence:
|
Determine repair procedures
|
|
Correct information is accessed and interpreted from manufacturer/component supplier specifications Completed |
Evidence:
|
Engine block and sub-assembly components are measured against manufacturer/component supplier specifications and tolerances Completed |
Evidence:
|
Inspection/measurement/testing is completed without causing damage to any component or system Completed |
Evidence:
|
Engine block and sub-assembly components are evaluated against measurements, tests and inspections made Completed |
Evidence:
|
Repair requirements are identified and reported according to enterprise policy and procedures Completed |
Evidence:
|
Repair requirements are completed according to enterprise and manufacturer/component supplier requirements Completed |
Evidence:
|
Workplace documentation is completed and dealt with relevant to inspection/measurement/testing outcomes Completed |
Evidence:
|
Inspection/measurement/testing activities are carried out according to industry regulations/guidelines, OH&S legislation, legislation and enterprise procedures/policies Completed |
Evidence:
|
Prepare to assemble engine block
|
|
OH&S requirements and personal protection needs are observed throughout the work Completed |
Evidence:
|
Procedures and information such as workshop manuals and specifications, and tooling, are sourced Completed |
Evidence:
|
Method options are analysed and those most appropriate to the circumstances are selected and prepared Completed |
Evidence:
|
Technical and/or calibration requirements for assembly are sourced and support equipment is identified and prepared Completed |
Evidence:
|
Measuring equipment is accessed Completed |
Evidence:
|
Check tolerances
|
|
Correct tolerances are obtained using manufacturer/ component supplier specifications Completed |
Evidence:
|
Tolerances are checked without causing damage to any component or system Completed |
Evidence:
|
Tasks carried out to comply within established industry guidelines Completed |
Evidence:
|
Assemble engine block and sub-assemblies/fit cylinder head(s)
|
|
Engine block and sub-assemblies are assembled and cylinder head(s) fitted without causing damage to any component or system Completed |
Evidence:
|
Assembly and fitting is carried out to comply with manufacturer/component supplier specifications and established industry guidelines and Australian Standards Completed |
Evidence:
|
Assembly and fitting activities are carried out according to industry regulations/guidelines, OH&S legislation, legislation and enterprise procedures/policies Completed |
Evidence:
|
Carry out testing and adjustment procedures
|
|
Testing and adjustment are carried out to comply with manufacturer/component supplier specifications, established industry guidelines and Australian Standards Completed |
Evidence:
|
Tests and adjustments are performed using industry approved procedures and equipment Completed |
Evidence:
|
Tests and adjustments are completed without causing damage to any component or system Completed |
Evidence:
|
Testing and adjustment activities are carried out according to industry regulations/guidelines, OH&S legislation, legislation and enterprise procedures/policies Completed |
Evidence:
|
Prepare equipment for use or storage
|
|
Work performed is documented and completed Completed |
Evidence:
|
Final inspection is made to ensure safety features are in place Completed |
Evidence:
|
Equipment is cleaned for use or storage to workplace expectations Completed |
Evidence:
|
Job card is processed in accordance with workplace procedures Completed |
Evidence:
|