NTISthis.com

Evidence Guide: CPCCCO3050A - Carry out high performance concreting

Student: __________________________________________________

Signature: _________________________________________________

Tips for gathering evidence to demonstrate your skills

The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!

From the Wiki University

 

CPCCCO3050A - Carry out high performance concreting

What evidence can you provide to prove your understanding of each of the following citeria?

Plan and prepare.

  1. Work instructions, work health and safety (WHS) requirements and other information relevant to the work are identified, confirmed and applied for planning and preparation purposes.
  2. Plant, tools and equipment consistent with job requirements are selected and checked for serviceability, and faults are rectified and reported before work begins.
  3. Material quantity requirements are identified and calculated according to plans, specifications and quality requirements.
  4. Materials appropriate to the work application are obtained, prepared, safely handled and located ready for use.
  5. Environmental requirements are identified for the project according to environmental plans and regulatory requirements.
Work instructions, work health and safety (WHS) requirements and other information relevant to the work are identified, confirmed and applied for planning and preparation purposes.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Plant, tools and equipment consistent with job requirements are selected and checked for serviceability, and faults are rectified and reported before work begins.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Material quantity requirements are identified and calculated according to plans, specifications and quality requirements.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Materials appropriate to the work application are obtained, prepared, safely handled and located ready for use.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Environmental requirements are identified for the project according to environmental plans and regulatory requirements.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Assessed

Teacher: ___________________________________ Date: _________

Signature: ________________________________________________

Comments:

 

 

 

 

 

 

 

 

Instructions to Assessors

Evidence Guide

The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

This unit of competency could be assessed by undertaking a range of tasks in the workplace or a close simulation of the workplace environment, provided that simulated or project-based assessment techniques fully replicate construction workplace conditions, materials, activities, responsibilities and procedures.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

A person should demonstrate the ability to:

complete planning, preparation, placement, finishing and curing of 10 square metres of high performance concrete to engineer’s specifications

locate, interpret and apply relevant information, standards and specifications relating to carrying out high performance concreting

comply with site safety plans and procedures

comply with organisational policies and procedures relating to carrying out high performance concreting while maintaining quality requirements outlined in job specifications

safely and effectively operate and use plant, tools and equipment required to carry out high performance concreting

communicate and work effectively and safely with others.

Context of and specific resources for assessment

Assessment of this unit:

must be in the context of the work environment

may be conducted in an off-site context, provided it is realistic and sufficiently rigorous to cover all aspects of workplace performance, including task skills, task management skills, contingency management skills and job role environment skills

must meet relevant compliance requirements.

Resource implications for assessment include:

an induction procedure

realistic tasks or simulated tasks covering the mandatory task requirements

tools and equipment appropriate to applying safe work practices

support materials appropriate to activity

workplace instructions relating to safe work practices and addressing hazards and emergencies

research resources and industry-related systems information

safety data sheets.

Method of assessment

Assessment for this unit must verify the practical application of the required skills and knowledge, using a combination of the following methods:

direct observation of tasks in real or simulated work conditions

questioning to confirm the ability to consistently identify and correctly interpret the essential underpinning knowledge required for practical application

review of relevant authenticated documentation from third parties, such as existing supervisors, team leaders or specialist training staff.

Guidance information for assessment

This unit could be assessed on its own or in combination with other units relevant to the job function.

Reasonable adjustments for people with disabilities must be made to assessment processes where required. This could include access to modified equipment and other physical resources, and the provision of appropriate assessment support.

Assessment processes and techniques should, as far as is practical, take into account the language, literacy and numeracy capacity of the candidate in relation to the competency being assessed.

Required Skills and Knowledge

Required skills

learning skills to:

evaluate own actions and make judgments about performance and necessary improvements

respond to change, such as differences in work site, and environmental and quality requirements

numeracy skills to:

check levels of lubricants in tools

calculate and confirm correct quantities of materials for work tasks

oral communication skills to:

enable clear and direct communication, using questioning to identify and confirm requirements, and share information

report work site hazards to appropriate personnel, including faults in tools, equipment or materials

use language and concepts appropriate to cultural differences

reading skills to:

interpret documentation, including drawings and specifications

understand written instructions, procedures and signage

interpret manufacturer instructions for safely handling tools and equipment

writing skills to complete pre-operational checklists and equipment fault forms

Required knowledge

general construction terminology

processes for calculating material requirements

properties, strength and performance of concrete:

placement, finishing and curing techniques

concrete testing techniques

high performance concrete materials and techniques

quality requirements:

internal organisational quality policy and standards

manufacturer specifications where specified

relevant regulations and Australian standards

workplace operations and procedures

substructure construction

processes for material storage and environmentally friendly waste management

types, characteristics, uses and limitations of plant, tools and equipment used in carrying out high performance concreting

types, location and use of relevant safety information:

job safety analyses (JSA) and safe work method statements (SWMS)

safety data sheets (SDS)

safety manuals and instructions for plant, tools and equipment

signage

environmental and work site safety plans

workplace and equipment safety requirements

Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Work health and safety requirements must comply with state and territory legislation and regulations and project safety plan, and may include:

assistance of others or the use of manual or mechanical lifting devices with handling activities where size, weight or other issues, such as disability, are a factor

emergency procedures, including extinguishing fires, organisational first aid requirements, and evacuation procedures

hazard control

hazardous materials and substances

personal protective equipment (PPE) prescribed under legislation, regulations and workplace policies and practices

safe operating procedures, including the conduct of operational risk assessment and treatments associated with:

earth leakage boxes

lighting

power cables, including overhead service trays, cables and conduits

restricted access barriers

surrounding structures

traffic control

trip hazards

work site visitors and the public

working at heights

working in confined spaces

working in proximity to others

working outdoors in warm climates

use of firefighting equipment

use of tools and equipment

workplace environmental requirements and safety.

Information may include:

instructions issued by authorised organisational and external personnel

memos

regulatory and legislative requirements relating to carrying out high performance concreting, including relevant Australian standards

safe work procedures relating to carrying out high performance concreting

safety data sheets

signage

verbal, written and diagrammatical instructions, including manufacturer specifications and instructions where specified

work bulletins

work schedules, plans and specifications.

Planning and preparation must include:

assessing conditions and hazards

determining work requirements and safety plans and procedures

identifying and rectifying equipment defects

inspecting work sites.

Tools and equipment:

must include:

bull floats

composite floats

immersion vibrators

magnesium floats

power floats

rakes

screed boards

shovels

steel trowels

vibrating screeds

may include:

bolt cutters

brooms

concrete kibbles

curing compounds applicators

edging tools

measuring tapes

nips

tarpaulins and covers

tremmies

wheelbarrows

wooden floats.

Quality requirements must include:

internal organisational quality policy and standards

manufacturer specifications where specified

relevant regulations and Australian standards

workplace operations and procedures.

Materials:

must include high performance concrete

may include:

curing compounds

a range of specialist additives.

Environmental requirements may include:

clean-up management

dust and noise control

vibration management

waste management.

High performance concrete includes the following applications:

airport runways

bridges

columns

cooling towers

dams

foundation supports for high rise facilities

foundations

gutters

hardstands

kerbs

pathways

pits

plinths

roadways

slabs

stairs

tunnels

walls.

Concrete placing methods may include:

kibble

pumping equipment

shovelling

tremmies

truck-placed

vibrating

wheelbarrows.

Screeding:

must include a hand screed

may include:

a mechanical vibrating screed

magic screeds.

Finishing techniques may include:

broom finished

brushed

bull float

mechanical trowelling machine

steel trowel

wood float.