NTISthis.com

Evidence Guide: FWPWPP2209 - Saw products from continuous ply

Student: __________________________________________________

Signature: _________________________________________________

Tips for gathering evidence to demonstrate your skills

The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!

From the Wiki University

 

FWPWPP2209 - Saw products from continuous ply

What evidence can you provide to prove your understanding of each of the following citeria?

Prepare for cutting

  1. Review work order and where required check with appropriate personnel.
  2. Select appropriate personal protective and other equipment and check for operational effectiveness.
  3. Obtain type and quantity of continuous ply to be cut from storage location.
  4. Plan material cutting patterns and saw set-up sequences in line with work order.
Review work order and where required check with appropriate personnel.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Select appropriate personal protective and other equipment and check for operational effectiveness.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Obtain type and quantity of continuous ply to be cut from storage location.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Plan material cutting patterns and saw set-up sequences in line with work order.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Cut continuous ply to size

  1. Use equipment in line with organisational safety procedures, manufacturer’s instructions and environmental protection practices.
  2. Mark material and set stops in preparation for cutting.
  3. Set-up ply on in-feed and feed systems, check and regularly adjust rate.
  4. Follow cutting sequence and patterns to produce required quantity.
  5. Check cuts for length or angle within set tolerance.
  6. Dispose of incorrect cuts, off cuts and defective material in line with environmental protection practices.
  7. Stack material safely in designated location in line with work order.
Use equipment in line with organisational safety procedures, manufacturer’s instructions and environmental protection practices.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Mark material and set stops in preparation for cutting.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Set-up ply on in-feed and feed systems, check and regularly adjust rate.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Follow cutting sequence and patterns to produce required quantity.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Check cuts for length or angle within set tolerance.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Dispose of incorrect cuts, off cuts and defective material in line with environmental protection practices.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Stack material safely in designated location in line with work order.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Complete operator maintenance

  1. Follow organisational safety procedures to lock out equipment.
  2. Check saw blades for bluntness or damage.
  3. Remove and replace saw blades in line with manufacturer's recommendations.
  4. Dispose of used blades in line with environmental protection practices.
  5. Keep work area clear of dust and debris in line with organisational safety procedures.
  6. Record and report production outcomes, equipment faults and maintenance requirements to appropriate personnel.
Follow organisational safety procedures to lock out equipment.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Check saw blades for bluntness or damage.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Remove and replace saw blades in line with manufacturer's recommendations.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Dispose of used blades in line with environmental protection practices.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Keep work area clear of dust and debris in line with organisational safety procedures.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Record and report production outcomes, equipment faults and maintenance requirements to appropriate personnel.

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Assessed

Teacher: ___________________________________ Date: _________

Signature: ________________________________________________

Comments:

 

 

 

 

 

 

 

 

Instructions to Assessors

Evidence Guide

Elements describe the essential outcomes.

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold italicised text is used, further information is detailed in the range of conditions.

1. Prepare for cutting

1.1 Review work order and where required check with appropriate personnel.

1.2 Select appropriate personal protective and other equipment and check for operational effectiveness.

1.3 Obtain type and quantity of continuous ply to be cut from storage location.

1.4 Plan material cutting patterns and saw set-up sequences in line with work order.

2. Cut continuous ply to size

2.1 Use equipment in line with organisational safety procedures, manufacturer’s instructions and environmental protection practices.

2.2 Mark material and set stops in preparation for cutting.

2.3 Set-up ply on in-feed and feed systems, check and regularly adjust rate.

2.4 Follow cutting sequence and patterns to produce required quantity.

2.5 Check cuts for length or angle within set tolerance.

2.6 Dispose of incorrect cuts, off cuts and defective material in line with environmental protection practices.

2.7 Stack material safely in designated location in line with work order.

3. Complete operator maintenance

3.1 Follow organisational safety procedures to lock out equipment.

3.2 Check saw blades for bluntness or damage.

3.3 Remove and replace saw blades in line with manufacturer's recommendations.

3.4 Dispose of used blades in line with environmental protection practices.

3.5 Keep work area clear of dust and debris in line with organisational safety procedures.

3.6 Record and report production outcomes, equipment faults and maintenance requirements to appropriate personnel.

Required Skills and Knowledge

Elements describe the essential outcomes.

Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold italicised text is used, further information is detailed in the range of conditions.

1. Prepare for cutting

1.1 Review work order and where required check with appropriate personnel.

1.2 Select appropriate personal protective and other equipment and check for operational effectiveness.

1.3 Obtain type and quantity of continuous ply to be cut from storage location.

1.4 Plan material cutting patterns and saw set-up sequences in line with work order.

2. Cut continuous ply to size

2.1 Use equipment in line with organisational safety procedures, manufacturer’s instructions and environmental protection practices.

2.2 Mark material and set stops in preparation for cutting.

2.3 Set-up ply on in-feed and feed systems, check and regularly adjust rate.

2.4 Follow cutting sequence and patterns to produce required quantity.

2.5 Check cuts for length or angle within set tolerance.

2.6 Dispose of incorrect cuts, off cuts and defective material in line with environmental protection practices.

2.7 Stack material safely in designated location in line with work order.

3. Complete operator maintenance

3.1 Follow organisational safety procedures to lock out equipment.

3.2 Check saw blades for bluntness or damage.

3.3 Remove and replace saw blades in line with manufacturer's recommendations.

3.4 Dispose of used blades in line with environmental protection practices.

3.5 Keep work area clear of dust and debris in line with organisational safety procedures.

3.6 Record and report production outcomes, equipment faults and maintenance requirements to appropriate personnel.

A person demonstrating competency in this unit must satisfy all of the elements, performance criteria and foundation skills of this unit. If a specific volume or frequency is not stated below, then evidence must be provided that the following requirements have been performed on at least one occasion:

produce sawn panels from continuous ply in line with individual work orders prescribing different lengths and tolerances and number of panels for each job

across the above jobs, complete cutting patterns and sequences for single straight cuts and angles requiring one cutting pass set for multiple cuts of the same size

for each of the above jobs, stack batches of sawn panels in storage location according to common length

after each of the above jobs, complete operator maintenance on the saw used.

A person competent in this unit must be able to demonstrate knowledge of:

environmental protection practices for forest products factory settings:

reducing water and energy use

cleaning plant, tools and equipment

disposing of, recycling and reusing timber ply and other waste

storage layout and categories for:

raw materials

stacking finished panels

typical continuous ply defects and how they affect ability to produce quality sawn panels:

warp

wane

cupping

shakes

insect defects

knots

resin pockets

cutting patterns and sequences for single straight cuts and angles requiring one cutting pass

range of industry standard lengths, tolerances and applicable terminology

purpose, features and operation of equipment used to saw products from continuous ply:

measuring equipment

power operated, manually controlled docking and trimming saws with carriages

saws with adjustable angle

saws with one or multiple blades

bandsaws

panel saws

table saws

bench saws

feed systems with rollers which support continuous ply

methods for assessing saw blade condition and completing and basic non-specialist repair and maintenance for saws

organisational procedures specific to sawing products from continuous ply:

workplace health and safety with particular emphasis on equipment lock out and use of personal protective equipment

communication reporting lines

recording and reporting production outcomes, equipment faults and maintenance requirements.

Range Statement

Not Applicable