NTISthis.com

Evidence Guide: PMC552057B - Finish casting operation

Student: __________________________________________________

Signature: _________________________________________________

Tips for gathering evidence to demonstrate your skills

The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!

From the Wiki University

 

PMC552057B - Finish casting operation

What evidence can you provide to prove your understanding of each of the following citeria?

Adjust and level mould and accessories

  1. Ensure position of mould base is level and stabilised according to standard operating procedures
  2. Adjust level of pipes and other accessories already fitted as required
Ensure position of mould base is level and stabilised according to standard operating procedures

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Adjust level of pipes and other accessories already fitted as required

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Position and fit reinforcement and accessories

  1. Place reinforcement in green concrete according to work as required
  2. Place fittings/accessories in concrete to specification
Place reinforcement in green concrete according to work as required

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Place fittings/accessories in concrete to specification

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Top up mould and finish

  1. Top up and cover mould according to work instructions
  2. Finish and patch product to specification
  3. Clean mould and work site as required by good occupational hygiene practices
Top up and cover mould according to work instructions

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Finish and patch product to specification

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Clean mould and work site as required by good occupational hygiene practices

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Rectify routine problems

  1. Identify the range of faults that can occur during the operation
  2. Determine and rectify fault causes by procedures/work instructions
  3. Identify and rectify equipment failure causes in accordance with procedures/work instructions
  4. Ensure appropriate records and log books of equipment operations are maintained to meet procedures/work instructions
  5. Identify non-routine problems and report to designated person
Identify the range of faults that can occur during the operation

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Determine and rectify fault causes by procedures/work instructions

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Identify and rectify equipment failure causes in accordance with procedures/work instructions

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Ensure appropriate records and log books of equipment operations are maintained to meet procedures/work instructions

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Identify non-routine problems and report to designated person

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Control hazards

  1. Identify hazards from the job to be done
  2. Identify other hazards in the work area
  3. Assess the risks arising from those hazards
  4. Implement measures to control those risks in line with procedures
Identify hazards from the job to be done

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Identify other hazards in the work area

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Assess the risks arising from those hazards

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Implement measures to control those risks in line with procedures

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Assessed

Teacher: ___________________________________ Date: _________

Signature: ________________________________________________

Comments:

 

 

 

 

 

 

 

 

Instructions to Assessors

Evidence Guide

The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.

Overview of assessment

The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

It is essential that the process be understood and that the importance of critical material properties, mixing variables, topping up and fitting of accessories is known. Competence must be demonstrated in the ability to recognise and analyse potential situations requiring action and then in implementing appropriate corrective action.

Consistent performance should be demonstrated. In particular look to see that:

reinforcing is fitted according specification

accessories are fitted as required by work instructions

moulded product is level, according to specification.

Competence must be demonstrated in the operation of all ancillary equipment to the level required for this unit of competency.

Context of and specific resources for assessment

Assessment will require access to an operating plant over an extended period of time, or a suitable method of gathering evidence of operating ability over a range of situations.

Assessment will occur over a range of situations which will include disruptions to normal, smooth operation.

Simulation or case studies/scenarios may be required to allow for timely assessment of parts of this unit of competency. Simulation should be based on the actual plant and will include 'walk-throughs' of the relevant competency components. A bank of scenarios/case studies/what ifs and questions will be required to probe the reasoning behind observable actions.

Method of assessment

Individual enterprises may choose to add prerequisites and co-requisites relevant to their processes.

Guidance information for assessment

Assessment processes and techniques must be culturally appropriate and appropriate to the language and literacy capacity of the candidate and the work being performed.

Required Skills and Knowledge

Required skills

Required skills include:

recognising conditions which will lead to out of specification product and taking appropriate action

implementing the enterprise's procedures within time constraints and in a manner relevant to the correct use of the equipment

conveying information relevant to the operation clearly and effectively

maintaining appropriate levels of quality assurance

reading and numeracy to interpret workplace documents and technical information

Required knowledge

Required knowledge includes:

topping up and finishing process

principles of concrete mixing

principles of reinforcing concrete to specification

principles of fitting accessories to specification

principles of concrete product finishing

underlying causes of faults such as precipitated by:

material

mixing

finishing

Range Statement

The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.

Procedures

All operations are performed in accordance with standard procedures and work instructions

Typical accessories

Typical accessories may include:

hooks

pipes

rubber tubing

Typical veneering

Typical veneering may include:

screeding

floating

helicopter floating

brushing

Occupational health and safety (OHS)

The identification and control of hazards and the application of OHS is to be in accordance with current, applicable legislation and regulations, and company procedures. All work is carried out at all times in accordance with these requirements