NTISthis.com

Evidence Guide: UEEEC0026 - Enter and verify programs for fire protection systems

Student: __________________________________________________

Signature: _________________________________________________

Tips for gathering evidence to demonstrate your skills

The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!

From the Wiki University

 

UEEEC0026 - Enter and verify programs for fire protection systems

What evidence can you provide to prove your understanding of each of the following citeria?

Prepare to enter operating instructions

  1. Work health and safety (WHS)/occupational health and safety (OHS) requirements and workplace procedures for a given work area are identified and applied
Work health and safety (WHS)/occupational health and safety (OHS) requirements and workplace procedures for a given work area are identified and applied

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

WHS/OHS risk control measures and procedures are followed in preparation for the work

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Safety hazards that have not previously been identified are assessed, reported and advice on risk control measures sought from work supervisor

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Extent of programming work is determined from job specifications and in consultation with appropriate person/s

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Tools, equipment and testing devices needed to carry out fire protection work activities are obtained and checked for correct operation and safety

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Fire protection device installation is checked for compliance with job specification, industry standards and regulations

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Enter software operating instructions

  1. WHS/OHS risk control measures and workplace procedures for carrying out the work are followed
WHS/OHS risk control measures and workplace procedures for carrying out the work are followed

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Circuits/machines/plant are checked and isolated in accordance with WHS/OHS requirements and workplace procedures

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Status of each function of the fire protection device is entered and their parameters set in accordance with manufacturer programming instructions

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Entered data is checked as meeting those specified by work activity and job specifications

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Unplanned situations are responded to in accordance with workplace procedures in a manner that minimises risk to personnel and equipment

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Programming is carried out efficiently without waste of materials and energy or damage to apparatus, the surrounding environment or other services

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Test fire protection device operation and report findings

  1. Fire protection device operation is tested in accordance with WHS/OHS requirements and workplace procedures
Fire protection device operation is tested in accordance with WHS/OHS requirements and workplace procedures

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Operating anomalies are identified and corrected in accordance with workplace procedure

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

WHS/OHS work completion risk control measures and workplace procedures are followed

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Worksite is cleaned and made safe in accordance with workplace procedures

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Work completion is reported and appropriate person/s notified in accordance with workplace procedure

Completed
Date:

Teacher:		 Evidence:

 

 

 

 

 

 

 

Assessed

Teacher: ___________________________________ Date: _________

Signature: ________________________________________________

Comments:

 

 

 

 

 

 

 

 

Instructions to Assessors

Required Skills and Knowledge

Evidence required to demonstrate competence in this unit must be relevant to and satisfy all of the requirements of the elements, performance criteria and range of conditions on at least two separate occasions and include:

apply sustainable energy principles and practices

applying relevant work health and safety (WHS)/occupational health and safety (WHS/OHS) requirements, including using risk control measures

correcting programming anomalies

dealing with unplanned events/situations in accordance with workplace procedures in a manner that minimises risk to personnel and equipment

entering functions and parameters correctly

identifying non-compliance conditions of device installation

performing program backups, version controls and documentation

testing and verifying device operation

understanding required operating functions and parameters.

Evidence required to demonstrate competence in this unit must be relevant to and satisfy all of the requirements of the elements, performance criteria and range of conditions and include knowledge of:

fire protection systems programming methods

input devices, including conventional alarm zones, analogue or analogue addressable fire detectors, flow switch connections or switch connections

logic times, including software programs that control the operation of non-latching detectors and timer periods before operation of fire system suppression systems

output devices, including shutdown signal, door or system release controls and solenoid valve controls

program backup, version control and documentation requirements

program loading methods and relevant information technology

program testing methods

relevant manufacturer specifications

relevant job safety assessments or risk mitigation processes

relevant WHS/OHS legislated requirements

relevant workplace documentation

relevant workplace policies and procedures

system interface controls, including verify signals to remote control and indicating equipment, building monitoring systems, paging system and colour graphics

system variables, including standard software functions that operate smoke detector controls, dual zone alarm configurations, alarm and fault global functions

vender programming codes and functions, including:

input/output (I/O) instructions

variables

timers

limitations of vender software.

Range Statement

Range is restricted to essential operating conditions and any other variables essential to the work environment.

Non-essential conditions may be found in the UEE Electrotechnology Training Package Companion Volume Implementation Guide.

Entering and verifying programs for fire protection systems must include at least the following:

two types of microprocessor fire protection control and indicating equipment with:

at least 50 input devices

at least 20 output devices

at least 1 system interface control

at least 2 logic timers

system variables