NTISthis.com

Evidence Guide: UEENEEG103A - Install low voltage wiring and accessories

Student: __________________________________________________

Signature: _________________________________________________

Tips for gathering evidence to demonstrate your skills

The important thing to remember when gathering evidence is that the more evidence the better - that is, the more evidence you gather to demonstrate your skills, the more confident an assessor can be that you have learned the skills not just at one point in time, but are continuing to apply and develop those skills (as opposed to just learning for the test!). Furthermore, one piece of evidence that you collect will not usualy demonstrate all the required criteria for a unit of competency, whereas multiple overlapping pieces of evidence will usually do the trick!

From the Wiki University

 

UEENEEG103A - Install low voltage wiring and accessories

What evidence can you provide to prove your understanding of each of the following citeria?

Prepare to install wiring and accessories.

  1. OHS procedures for a given work area are identified, obtained and understood.
  2. Health and safety risks are identified and established risk control measures and procedures in preparation for the work are followed.
  3. Safety hazards that have not previously been identified are noted and established risk control measures are implemented.
  4. Installation of wiring is prepared in consultation with other affected by the work and sequenced appropriately.
  5. The nature and location of the work is determined from documentation or other appropriate person to establish the scope of work to be undertaken.
  6. Cable routes are planned within the constraints of the building structure, significants and requirements.
  7. Material needed for the installation work is obtained in accordance with established procedures and checked against job requirements.
  8. Tools, equipment and testing devices needed to for the installation work are obtained in accordance with established procedures and checked for correct operation and safety.
  9. Preparatory work is checked to ensure no damage has occurred and complies with requirements.
OHS procedures for a given work area are identified, obtained and understood.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Health and safety risks are identified and established risk control measures and procedures in preparation for the work are followed.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Safety hazards that have not previously been identified are noted and established risk control measures are implemented.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Installation of wiring is prepared in consultation with other affected by the work and sequenced appropriately.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

The nature and location of the work is determined from documentation or other appropriate person to establish the scope of work to be undertaken.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Cable routes are planned within the constraints of the building structure, significants and requirements.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Material needed for the installation work is obtained in accordance with established procedures and checked against job requirements.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Tools, equipment and testing devices needed to for the installation work are obtained in accordance with established procedures and checked for correct operation and safety.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Preparatory work is checked to ensure no damage has occurred and complies with requirements.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Install wiring and accessories.

  1. OHS risk control measures and procedures for carrying out the work are followed.
  2. The need to test or measure live is determined in strict accordance with OHS requirements and when necessary conducted within established safety procedures.
  3. Circuits/machines/plant are checked as being isolated where necessary in strict accordance OHS requirements and procedures.
  4. Wiring and accessories are installed to comply with technical standards and job specifications and requirements with sufficient excess to affect terminations.
  5. Accessories are installed straight and square in the required locations and within acceptable tolerances.
  6. Cables and conductors are terminated at accessories in accordance with manufacture's specifications and regulatory requirements.
  7. Ongoing compliance and safety inspection of installed wiring systems and testing of installed circuits is undertaken.
  8. Defects revealed through on-going compliance and safety inspection and tests are rectified.
  9. Cable installation and termination is carried out efficiently without unnecessary waste of materials or damage to apparatus, circuits or the surrounding environment and using sustainable energy practices.
  10. Unexpected situations are dealt with safely and with the approval of an authorised person.
OHS risk control measures and procedures for carrying out the work are followed.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

The need to test or measure live is determined in strict accordance with OHS requirements and when necessary conducted within established safety procedures.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Circuits/machines/plant are checked as being isolated where necessary in strict accordance OHS requirements and procedures.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Wiring and accessories are installed to comply with technical standards and job specifications and requirements with sufficient excess to affect terminations.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Accessories are installed straight and square in the required locations and within acceptable tolerances.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Cables and conductors are terminated at accessories in accordance with manufacture's specifications and regulatory requirements.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Ongoing compliance and safety inspection of installed wiring systems and testing of installed circuits is undertaken.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Defects revealed through on-going compliance and safety inspection and tests are rectified.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Cable installation and termination is carried out efficiently without unnecessary waste of materials or damage to apparatus, circuits or the surrounding environment and using sustainable energy practices.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Unexpected situations are dealt with safely and with the approval of an authorised person.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Completion and report installation activities.

  1. OHS work completion risk control measures and procedures are followed.
  2. Work site is cleaned and made safe in accordance with established procedures.
  3. 'As-installed' cables/wiring and accessories is documented and an appropriate person or persons notified in accordance with established procedures.
OHS work completion risk control measures and procedures are followed.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Work site is cleaned and made safe in accordance with established procedures.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

'As-installed' cables/wiring and accessories is documented and an appropriate person or persons notified in accordance with established procedures.

Completed
Date:

Teacher:
Evidence:

 

 

 

 

 

 

 

Assessed

Teacher: ___________________________________ Date: _________

Signature: ________________________________________________

Comments:

 

 

 

 

 

 

 

 

Instructions to Assessors

Evidence Guide

9) The evidence guide provides advice on assessment and must be read in conjunction with the Performance Criteria, Required Skills and Knowledge, the Range Statement and the Assessment Guidelines for this Training Package.

The Evidence Guide forms an integral part of this unit. It must be used in conjunction with all parts of this unit and performed in accordance with the Assessment Guidelines of this Training Package.

Overview of Assessment

9.1)

Longitudinal competency development approaches to assessment, such as Profiling, require data to be reliably gathered in a form that can be consistently interpreted over time. This approach is best utilised in Apprenticeship programs and reduces assessment intervention. It is the Industry's preferred model for apprenticeships. However, where summative (or final) assessment is used it is to include the application of the competency in the normal work environment or, at a minimum, the application of the competency in a realistically simulated work environment. It is recognised that, in some circumstances, assessment in part or full can occur outside the workplace. However, it must be in accordance with industry and regulatory policy.

Methods chosen for a particular assessment will be influenced by various factors. These include the extent of the assessment, the most effective locations for the assessment activities to take place, access to physical resources, additional safety measures that may be required and the critical nature of the competencies being assessed.

The critical safety nature of working with electricity, electrical equipment, gas or any other hazardous substance/material carries risk in deeming a person competent. Sources of evidence need to be 'rich' in nature to minimise error in judgment.

Activities associated with normal every day work have a bearing on the decision as to how much and how detailed the data gathered will contribute to its 'richness'. Some skills are more critical to safety and operational requirements while the same skills may be more or less frequently practised. These points are raised for the assessors to consider when choosing an assessment method and developing assessment instruments. Sample assessment instruments are included for Assessors in the Assessment Guidelines of this Training Package.

Critical aspects of evidence required to demonstrate competency in this unit

9.2)

Before the critical aspects of evidence are considered all prerequisites shall be met.

Evidence for competence in this unit shall be considered holistically. Each element and associated performance criteria shall be demonstrated on at least two occasions in accordance with the 'Assessment Guidelines - UEE07'. Evidence shall also comprise:

A representative body of work performance demonstrated within the timeframes typically expected of the discipline, work function and industrial environment. In particular this shall incorporate evidence that shows a candidate is able to:

Implement Occupational Health and Safety workplace procedures and practices including the use of risk control measures as specified in the performance criteria and range statement

Apply sustainable energy principles and practices as specified in the performance criteria and range statement

Demonstrate an understanding of the essential knowledge and associated skills as described in this unit. It may be required by some jurisdictions that RTOs provide a percentile graded result for the purpose of regulatory or licensing requirements.

Demonstrate an appropriate level of skills enabling employment

Conduct work observing the relevant Anti Discrimination legislation, regulations, polices and workplace procedures

Demonstrated consistent performance across a representative range of contexts from the prescribed items below:

Install wiring and accessories for low voltage circuits as described as described in 8) and including:

A

Reading and interpreting drawings related to cable layouts, cable schedules and apparatus locations.

B

Planning cable routes and obtaining installation materials.

C

Sequencing the installation effectively with other affected by the work.

D

Routing, placing and securing cables in compliance with requirements.

E

Placing and securing accessories accurately.

F

Maintaining fire integrity.

G

Terminating cable and conductors to comply with requirements.

H

Undertaking on-going compliance and safety inspection and testing of installed circuits.

I

Rectifying any defects revealed through on-going inspection and testing

J

Correctly documenting 'as-installed' cables/wiring and accessories.

K

Dealing with unplanned events

Context of and specific resources for assessment

9.3)

This unit should be assessed as it relates to normal work practice using procedures, information and resources typical of a workplace. This should include:

OHS policy and work procedures and instructions.

Suitable work environment, facilities, equipment and materials to undertake actual work as prescribed by this unit.

These should be part of the formal learning/assessment environment.

Note:

Where simulation is considered a suitable strategy for assessment, conditions must be authentic and as far as possible reproduce and replicate the workplace and be consistent with the approved industry simulation policy.

The resources used for assessment should reflect current industry practices in relation to installing wiring and accessories for low voltage circuits.

Method of assessment

9.4)

This unit shall be assessed by methods given in Volume 1, Part 3 'Assessment Guidelines'.

Note:
Competent performance with inherent safe working practices is expected in the industry to which this unit applies. This requires assessment in a structured environment which is primarily intended for learning/assessment and incorporates all necessary equipment and facilities for learners to develop and demonstrate the essential knowledge and skills described in this unit.

Concurrent assessment and relationship with other units

9.5)

For optimisation of training and assessment effort, competency development in this unit may be arranged concurrently with unit:

UEENEEG104A

Install appliances, switchgear and associated accessories for low voltage electrical installations

Required Skills and Knowledge

7) This describes the essential skills and knowledge and their level, required for this unit.

Evidence shall show that knowledge has been acquired of safe working practices and installing wiring and accessories for low voltage circuits.

All knowledge and skills detailed in this unit should be contextualised to current industry standards, technologies and practices.

KS01-EG103A Installation of wiring systems

Evidence shall show an understanding of the installation of wiring systems that comply with standards to an extent indicated by the following aspects:

T1 Standards, codes and requirements applicable to the installation of wiring systems encompassing:

Cables and methods of mechanical protection and support

Protection against and from other services.

Prohibited cable locations

Building codes affecting the installation of cables in buildings, structures and premises (limitation on penetration of structural elements, maintenance of fire protection integrity, and wiring above suspected ceilings)

Issues affecting electrical installations in heritage buildings and premises (limitation on penetration of structural and finished elements, accessing cable routes, types and colour of exposed accessories).

T2 Use of other installation standards called up by the Wiring Rules for special situations encompassing:

standards that apply to Electromedical treatment areas.

additional requirements for construction and demolition sites.

Relocatable installations and their site supply

additional requirements for caravan park.

additional requirements for marinas and pleasure craft at low voltage.

additional requirements for shows and carnivals.

T3 Hazardous areas encompassing:

Conditions that apply in an areas that require them to be classified as a ‘Hazardous area’.

Responsibility for classifying a hazardous area

Awareness of standards called up by the Wiring Rules for selection of equipment and installations in Hazardous areas. (AS/NZS 3000 requirements for hazardous areas).

T4 Requirement for the installation of cables and accessories in damp situations and ELV installations encompassing:

restricted zones around baths, showers, fixed water containers, pools, sauna heaters and fountains/water features for given installations.

selecting equipment suitable for installation in given damp situations.

voltage range that defines extra-low voltage.

'Separated extra-low voltage (SELV) system' and a 'Protected extra-low voltage (PELV) system".

AS/NZS 3000 requirements for selecting extra-low voltage systems and devices for a range of installations and conditions.

T5 Aerial cabling encompassing:

Describe the types of aerial cabling.

State the AS/NZS 3000 and local supply authority requirements for aerial cabling.

Termination of aerial cables in accordance with AS/NZS 3000 and local requirements.

installation of consumers mains for connection via overhead consumers terminals in accordance with AS/NZS 3000 and local requirements.

Testing of installed cables compliance with Australian Standards

T6 Underground cabling encompassing:

Describe permissible underground cabling systems.

Identify other underground services.

State the AS/NZS 3000 and local supply authority requirements for underground cabling.

List the advantages and disadvantages of underground wiring systems

selection of underground consumers mains in accordance with AS/NZS 3000 and local requirements

T7 Techniques for installing cables and wiring systems encompassing:

Typical cable routes through buildings, structures and premises.

Application of wiring accessories

Drawing-in, placing and fixing of cables

Cable and conductor terminations

Maintaining fire rating integrity.

Inspecting and testing installed and terminated cables to ensure they comply with continuity and insulation resistance and are safe to connect to the supply.

Range Statement

8) This relates to the unit as a whole providing the range of contexts and conditions to which the performance criteria apply. It allows for different work environments and situations that will affect performance.

This unit shall be demonstrated in relation to at least three different types of cable enclosure/support systems in combination with four different cable types and circuits for five different purposes as listed below.

Wiring systems enclosures and supports:

Metallic conduit

Non-metallic conduit

Trunking

Duct

Cable tray/ladder

Catenary

Posts/poles/struts

Cable types:

Thermoplastic insulated cable (TPI)

Flat thermoplastic sheathed (TPS)

Circular thermoplastic sheathed (TPS)

Steel wire armoured (SWA)

Fire rated cable ( HT or HF or MIMS)

Flexible cables

Aerial cable

Circuit purpose:

Consumers mains

Submains

Alternative supply

Lighting;

Socket outlets

Single phase fixed appliance

Single phase motor

Three phase motor

Control

Generic terms used throughout this Vocational Standard shall be regarded as part of the Range Statement in which competency is demonstrated. The definition of these and other terms that apply are given in Volume 2, Part 2.1.