Application
This unit of competency covers wet cleaning concrete sub-floors using high and low pressure water cleaning applications relating to sub-floor preparation.
Licensing, legislative or certification requirements may apply to this unit and relevant state/territory and local government agencies should be consulted to determine any necessary certification or licensing for undertaking flooring work. Access to construction sites requires certification of general induction training specified by the National Code of Practice for Induction for Construction Work (ASCC 2007).
Elements and Performance Criteria
Elements describe the essential outcomes. | Performance criteria describe the performance needed to demonstrate achievement of the element. | ||
1 | Identify wet cleaning operations | 1.1 | Applicable work health and safety (WHS), legislative and organisational requirements relevant to the application of wet cleaning methods are verified and complied with |
1.2 | Types of wet cleaning equipment and their functions are identified from relevant information sources and Australian Standards | ||
1.3 | Sources of power supply are recognised | ||
2 | Select wet cleaning method | 2.1 | Wet cleaning method, equipment and attachments are selected consistent with the needs of the job |
2.2 | Wet cleaning equipment is checked for serviceability and safety and any faults are corrected or processed for repair | ||
2.3 | Sequence of work is planned to ensure efficiency and quality of sub-floor cleaning | ||
3 | Prepare sub-floor for cleaning | 3.1 | Appropriate personal protective equipment is selected, correctly fitted and used |
3.2 | Fittings and fixtures are removed from the sub-floor | ||
3.3 | Sub-floor is cleared of loose debris and dirt, and cleaned | ||
3.4 | A safe flooring technology work environment is established and maintained | ||
4 | Clean the floor | 4.1 | The start point is established and work plan implemented |
4.2 | Perimeter is cleaned using appropriate method and equipment | ||
4.3 | Main area is cleaned to the required standard using the most appropriate available equipment in accordance with manufacturer specifications | ||
4.4 | Floor area is inspected and re-worked as required | ||
5 | Complete housekeeping | 5.1 | Tools and equipment are cleaned and stored appropriately |
5.2 | Work area is cleaned and rubbish disposed of appropriately | ||
5.3 | Workplace documentation is completed | ||
Evidence of Performance
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection processes to:
minimise the risk of injury to self or others
prevent damage to goods, equipment and products
maintain required production output and product quality
Adopt and carry out correct procedures prior to and during the application of each of the following wet cleaning methods:
high and low water pressure cleaning
detergent cleaning
acid etching
Apply ventilation standards
Complete operator maintenance on wet cleaning high and low water pressure equipment
Use mathematical ideas and techniques to correctly complete measurements, calculate area and estimate material requirements
Communicate ideas and information to enable confirmation of work requirements and specifications and the reporting of work outcomes and problems, interpret basic plans and follow safety procedures
Avoid backtracking, work flow interruptions or wastage
Work with others and in a team by recognising dependencies and using cooperative approaches to optimise work flow and productivity
Evidence of Knowledge
State or territory WHS legislation, regulations, standards and codes of practice relevant to the use of wet cleaning methods
Australian Standards, including AS/NZS 2455.1:2007 Textile floor coverings - Installation practice – General, and AS 1884-2012 Floor coverings - Resilient sheet and tiles - Installation practices
Organisational and site standards, requirements, policies and procedures for the use of wet cleaning methods
Types and characteristics of high and low water pressure, including requirements for their safe use, operation and maintenance
High and low water pressure equipment attachments, their uses, limitations and maintenance requirements
Environmental protection requirements
Established communication channels and protocols
Relevant problem identification and resolution
Assessment Conditions
Assessors must:
hold training and assessment competencies as determined by the National Skills Standards Council (NSSC) or its successors
have vocational competency in the furnishing industry at least to the level being assessed with broad industry knowledge and experience, usually combined with a relevant industry qualification
be familiar with the current skills and knowledge used and have relevant, current experience in the furnishing industry.
Assessment methods must confirm consistency of performance over time rather than a single assessment event and in a range of workplace relevant contexts.
Assessment must be by observation of relevant tasks with questioning on underpinning knowledge and, where applicable, multimedia evidence, supervisor’s reports, projects and work samples.
Assessment is to be conducted on single units of competency or in conjunction with other related units of competency. Foundation skills are integral to competent performance in the unit and should not be assessed separately.
Assessment must occur on the job or in a workplace simulated facility with relevant process, equipment, materials, work instructions and deadlines.
Access is required to access to high and low pressure wet cleaning equipment and manufacturer/user instructions and/or manuals.
Foundation Skills
Foundation skills essential to performance are explicit in the performance criteria of this unit of competency. Detail on appropriate performance levels for each furnishing unit of competency in reading, writing, oral communication and numeracy utilising the Australian Core Skills Framework (ACSF) are provided in the Furnishing Training Package Implementation Guide.
Range Statement
Specifies different work environments and conditions that may affect performance. Essential operating conditions that may be present (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) are included. Range is restricted to essential operating conditions and any other variables essential to the work environment. | |
Unit context includes: | WHS requirements, including legislation, building codes, material safety management systems, hazardous and dangerous goods codes, and local safe operating procedures or equivalent work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements work requires individual to demonstrate some discretion, judgement and problem solving |
Wet cleaning methods include: | high and low pressure water hosing detergent cleaning acid etching |
Types of wet cleaning equipment include: | low pressure sprayer booster pump air compressor hand held lance plastic sprinkling can mop stiff broom floor scrubber disc machine equipment with abrasive bristle brushes power washer suitable nozzle tips pressure rated hoses wet/dry vacuum squeegee run-off protection |
Sources of power supply include: | single or three-phase propane |
Attachments include: | wet/dry vacuum attachment suitable nozzle tips run-off protection |
Fault reporting includes: | identifying any faults in the operation of wet cleaning equipment verbal or written reporting |
Fittings and fixtures include: | nails door stops gripper strips metal mouldings |
Australian Standards include: | AS/NZS 2455.1:2007 Textile floor coverings - Installation practice - General AS 1884-2012 Floor coverings - Resilient sheet and tiles - Installation practices |
Personal protective equipment includes: | that prescribed under legislation, regulations and enterprise policies and practices |
Information and procedures include: | workplace procedures relating to the use of tools and equipment work instructions, including job sheets, cutting lists, plans, drawings and designs workplace procedures relating to reporting and communication manufacturer specifications and operational procedures |
Sectors
Flooring technology