Application
The unit applies to draping fabric with special considerations to fit balance, and inter-construction requirements of the jacket as an over-garment. Included, is the use of partial flat pattern construction or blocks to complement the drape, such as with the development of sleeves and collars. Draping may be for a one off garment that goes from drape to garment or a prototype that goes from drape to flat pattern for small volume production. Draping is performed on a body form such as a mannequin or model. Work is supervised and may be conducted in small to large scale enterprises and may involve individual and team-related activities. The application of this unit is according to OHS practices of the enterprise and workplace practices, which may include: requirements prescribed by legislation, awards agreements and conditions of employment standard operating procedures work instructions oral, written and visual communication quality practices, including responsibility for maintenance of own work quality and contribution to quality improvement of team or section output housekeeping tasks related to environmental protection, waste disposal, pollution control, and recycling This unit requires skills in planning and organising to plan and prepare for draping. Initiative and enterprise and problem solving skills are applied to conduct drape, make modifications and finalise drape. Communication skills are used to take measurements and record specifications. Self management skills are used to ensure results meet quality standards and design brief. |
Prerequisites
Prerequisites |
Elements and Performance Criteria
ELEMENT | PERFORMANCE CRITERIA |
1 Prepare draping tools and equipment | 1.1 Work area is set up according to OHS practices and specifications for work. 1.2 Draping tools and equipment are selected and prepared. 1.3 Body form that is one size larger than actual size is selected. 1.4 Body form is prepared by applying additional padding required of the design, eg shoulder pads. 1.5 Body reference points are marked with tape on body form. |
2 Prepare working drawings | 2.1 Design lines are identified and plotted on body form using narrow tape. 2.2 Working drawing is developed. 2.3 Measurements are checked. |
3 Prepare fabric for draping | 3.1 Dimensions of fabric pieces required for drape are estimated according to chosen design. 3.2 Warp, weft and bias grains of fabric are identified. 3.3 Fabric handling qualities are identified. |
4 Plan drape | 4.1 Requirements for adding design ease for movement are identified. 4.2 Requirements for manipulating dart excess are identified. 4.3 Seam positioning is planned. 4.4 Drape plan is developed. |
5 Perform draping | 5.1 Fabric is pinned on body form relating reference points and fabric grains. 5.2 Fabric is moulded and manipulated on body form according to the design, fit and design schematic. 5.3 Ease is added to allow for movement. 5.4 If a requirement of chosen design, fullness or volume is incorporated into draping. 5.5 Fabric is smoothed and manipulated over contours of over-garments and along sketch design lines. 5.6 Darts and seams are formed and pinned for pattern creation or garment construction. 5.7 Collars or built-up necklines are draped according to the design. 5.8 Cut-on or set-in sleeves are partially flat-constructed or designed then placed on the drape. 5.9 Reference points are pinned. 5.10 Sleeve design is incorporated into drape. 5.11 Front, back and sleeve drapes are prepared for truing. 5.12 Truing is performed. |
6 Finalise draping | 6.1 Drape is removed from body form. 6.2 Drape is finalised and directed to next production process. |
Required Skills
This describes the essential skills and knowledge and their level, required for this unit. |
Demonstrates knowledge of: principles and concepts of pattern making customer and workplace requirements cost efficiency in relation to pattern making range of typical garment fabrics, including weight and other characteristics flat pattern construction cutting and garment construction OHS practices, including hazard identification and control measures quality practices workplace practices recording and reporting practices |
Demonstrates skills to: interpret design brief or specifications interpret and apply defined procedures and motor skills consistently achieve quality and production output requirements read, interpret and follow information on work specifications, standard operating procedures and work instructions, and other reference material maintain accurate records communicate within the workplace sequence operations meet specifications clarify and check task-related information carry out work according to OHS practices |
Evidence Required
The Evidence Guide provides advice on assessment and must be read in conjunction with the Performance Criteria, Required Skills and Knowledge, the Range Statement and the Assessment Guidelines for the Training Package. | |
Critical aspects of evidence | Demonstrates skills and knowledge to: prepare tools, equipment and fabric pieces prepare design schematics develop a draping plan carry out the draping on the dress form finalise the drape for next process |
Consistency in performance | Consistently applies skills and knowledge when: organising work completing tasks identifying improvements using workplace practices using OHS practices recording and reporting accidents and incidents assessing operational readiness of equipment used and work processes recognising and adapting to cultural differences in the workplace, including modes of behaviour and interactions completing work systematically with attention to detail without damage to goods and equipment |
Resource implications | Access is required to real or appropriately simulated situations, including work areas, materials and equipment, and to information on workplace practices and OHS practices. |
Context for assessment | Assessment may occur on the job or in an appropriately simulated environment. |
Interdependent assessment | This unit may be assessed independently or in combination with other relevant units. |
Range Statement
The Range Statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the Performance Criteria, is detailed below. Add any essential operating conditions that may be present with training and assessment depending on the work situation, needs if the candidate, accessibility of the item, and local industry and regional contexts. | ||||
Legislative/regulatory requirements | All work must comply with relevant Federal and State or Territory legislative or regulatory requirements. | |||
OHS practices | OHS practices must include hazard identification and control, risk assessment and implementation of risk reduction measures specific to the tasks described by this unit and may include: manual handling techniques standard operating procedures personal protective equipment safe materials handling taking of rest breaks ergonomic arrangement of workplaces following marked walkways safe storage of equipment housekeeping reporting accidents and incidents other OHS practices relevant to the job and enterprise | |||
Draping tools and equipment may include: | body form narrow tape shoulder pads tape measure pen/pencil scissors square rule marker pens hole punch pins fashion triangle French curve pattern notcher weights | |||
Design schematics are: | the design lines as depicted in the fashion illustration that are then transferred onto the dress form using narrow tape | |||
Structured over-garments must include: | jacket or overcoat with set-in or cut-on sleeve collar lining creative and intricate styling | |||
Structured over-garments may include: | jackets/overcoats with set-in sleeves jackets/overcoats with cut-on sleeves - such as raglans and kimonos jackets/overcoats with volume-draped panels jackets/overcoats with cut-on collars | |||
Fabric must be: | the fabric of the final garment or a fabric that has the same handle or drape | |||
Fabric handling qualities may include: | fall stretch stability drape | |||
Drape plan may include | adding fullness (pleats, tucks, gathers) multiple darts/division of darts symmetric and/or asymmetric design features cowls, twists, knots |
Sectors
Sector | Fashion Design and Technology |
Employability Skills
This unit contains employability skills. |
Licensing Information
Not applicable.